Temperature Sensor with Alert Outputs Features:Converts Remote or Internal Diode Temperature to Analog VoltageAdjustable Overtemperature and Undertemperature ThresholdsVoltage Output Proportional to Temperature±1°C Remote Temperature Accuracy±2°C Internal Temperature AccuracyBuilt-In Series Resistance CancellationOpen Drain Alert Outputs2.25V to 5.5V Supply Voltage1.8V Reference Voltage Output200μA Quiescent Current10-Lead 3mm × 3mm DFN Package

Industrial Temperature Sensors TEMP PRB SUBMERS 10C +150C

The MAX6581 precision multichannel temperature sensor monitors its own temperature and the temperatures of up to seven external diode-connected transistors. All temperature channels have programmable alert and overtemperature thresholds. When the measured temperature of a channel crosses the respective threshold, a status bit is set in one of the status registers. Two open-drain alarm outputs (active-low ALERT and active-low OVERT) assert corresponding to these bits in the status register(s). Resistance cancellation is available for all channels and compensates for high series resistance in circuit-board traces and thermal diodes. The 2-wire serial interface accepts SMBus protocols (write byte, read byte, send byte, and receive byte) for reading the temperature data and programming the alarm thresholds. The MAX6581 is specified for an operating temperature range of -40°C to +125°C and is available in a 24-pin, 4mm × 4mm thin QFN package with an exposed pad.ApplicationsData CommunicationsDesktop ComputersNotebook ComputersServersWorkstations

The DS7505 low-voltage (1.7V to 3.7V) digital thermometer and thermostat provides 9-, 10-, 11-, or 12-bit digital temperature readings over a -55°C to +125°C range with ±0.5°C accuracy over a -0°C to +70°C range. A 9-bit resolution mode is software compatible with the LM75.The DS7505 thermostat has a dedicated open-drain output (O.S.) and programmable fault tolerance, which allows the user to define the number of consecutive error conditions that must occur before O.S. is activated. There are two thermostatic operating modes that control thermostat operation based on user-defined trip points (TOS and THYST) that are stored in EEPROM registers.ApplicationsAny Thermally Sensitive SystemCellular Base StationsMedical EquipmentNetworking EquipmentOffice Equipment

The DS7505 low-voltage (1.7V to 3.7V) digital thermometer and thermostat provides 9-, 10-, 11-, or 12-bit digital temperature readings over a -55°C to +125°C range with ±0.5°C accuracy over a -0°C to +70°C range. A 9-bit resolution mode is software compatible with the LM75.The DS7505 thermostat has a dedicated open-drain output (O.S.) and programmable fault tolerance, which allows the user to define the number of consecutive error conditions that must occur before O.S. is activated. There are two thermostatic operating modes that control thermostat operation based on user-defined trip points (TOS and THYST) that are stored in EEPROM registers.ApplicationsAny Thermally Sensitive SystemCellular Base StationsMedical EquipmentNetworking EquipmentOffice Equipment

This low-voltage (1.7V to 3.7V) digital thermometerand thermostat provides 9, 10, 11, or 12-bit digitaltemperature readings over a -55°C to +125°C rangewith ±2°C accuracy over a -25°C to +100°C range. Atpower-up, the DS75LX defaults to 9-bit resolution forsoftware compatibility with the LM75. Communicationwith the DS75LX is achieved through a simple 2-wireserial interface. Three tri-state address pins allow upto 27 DS75LX devices to operate on the same 2-wirebus, which greatly simplifies distributed temperature-sensingapplications.The DS75LX thermostat has a dedicated open-drainoutput (O.S.) and programmable fault tolerance,which allow the user to define the number ofconsecutive error conditions that must occur beforeO.S. is activated. There are two thermostaticoperating modes that control thermostat operationbased on user-defined trip-points (TOS and THYST).ApplicationsAny Thermally Sensitive SystemCellular Base StationsServersTelecom Switches and Routers

This low-voltage (1.7V to 3.7V) digital thermometerand thermostat provides 9, 10, 11, or 12-bit digitaltemperature readings over a -55°C to +125°C rangewith ±2°C accuracy over a -25°C to +100°C range. Atpower-up, the DS75LX defaults to 9-bit resolution forsoftware compatibility with the LM75. Communicationwith the DS75LX is achieved through a simple 2-wireserial interface. Three tri-state address pins allow upto 27 DS75LX devices to operate on the same 2-wirebus, which greatly simplifies distributed temperature-sensingapplications.The DS75LX thermostat has a dedicated open-drainoutput (O.S.) and programmable fault tolerance,which allow the user to define the number ofconsecutive error conditions that must occur beforeO.S. is activated. There are two thermostaticoperating modes that control thermostat operationbased on user-defined trip-points (TOS and THYST).ApplicationsAny Thermally Sensitive SystemCellular Base StationsServersTelecom Switches and Routers

The MAX6629–MAX6632 are local digital temperature sensors with an SPI-compatible serial interface. The temperature is converted to a 12-bit + sign word with a resolution of 0.0625°C/LSB. An extended temperature range provides useful readings up to +150°C.These sensors are 3-wire serial interface SPI compatible, allowing the MAX6629–MAX6632 to be readily connected to a variety of microcontrollers (µCs). The MAX6629–MAX6632 are read-only devices, simplifying their use in systems where only temperature data is required.All four digital temperature sensors require very little supply current, making them ideal for portable systems. The MAX6631/MAX6632 perform a temperature-to-digital conversion once every 8s and require minimal average supply current, 32µA (typ). The MAX6629/MAX6630 perform a conversion once every 0.5s and require only 200µA (typ) supply current. Any of these temperature sensors can perform conversions more often—up to approximately four conversions per second by reading the conversion results more often.ApplicationsCellularHard Disk DriveHVACsIndustrial ControlSystems

The MAX6680/MAX6681 are precise, two-channel digital thermometers. Each accurately measures the temperature of its own die and one remote PN junction and reports the temperature on a 2-wire serial interface. The remote junction can be a diode-connected transistor like the low-cost NPN type 2N3904 or PNP type 2N3906. The remote junction can also be a common-collector PNP, such as a substrate PNP of a microprocessor.The MAX6680/MAX6681 include pin-programmable default temperature thresholds for the active-low OVERT output, which provides fail-safe clock throttling or system shutdown. In addition, the devices are pin programmable to select whether the active-low OVERT output responds to either the local, remote, or both temperatures.The 2-wire serial interface accepts standard System Management Bus (SMBus™) commands such as Write Byte, Read Byte, Send Byte, and Receive Byte to read the temperature data and program the alarm thresholds and conversion rate. The MAX6680/MAX6681 can function autonomously with a programmable conversion rate, which allows the control of supply current and temperature update rate to match system needs. For conversion rates of 4Hz or less, the remote sensor temperature can be represented in extended mode as 10 bits + sign with a resolution of 0.125°C. When the conversion rate is 8Hz, output data is 7 bits + sign with a resolution of 1°C. The MAX6680/MAX6681 also include an SMBus timeout feature to enhance system reliability.The MAX6681 is an upgrade to the MAX6654. The MAX6680/MAX6681 remote accuracy is ±1°C with no calibration needed. They are available in a 16-pin QSOP package and operate throughout the -55°C to +125°C temperature range.ApplicationsDesktop ComputersNotebook ComputersServersThin ClientsWorkstations

MAX6685/MAX6686 are dual-output temperature switches that use an external diode-connected transistor as a sensing element. These devices have two logic outputs (THIGH and TLOW). THIGH asserts a logic signal when the remote temperature crosses the factory-programmed, +120°C, or +125°C upper trip threshold. TLOW is asserted when the remote temperature exceeds the lower threshold, which is controlled by pins S1 and S2. The lower thresholds are available in two ranges in 5°C increments. The two ranges are +40°C to +80°C and +75°C to +115°C. Hysteresis for both outputs to be deasserted is typically 5°C.THIGH is an open-drain, active-low output for both the MAX6685 and the MAX6686. TLOW is a CMOS push-pull, active-high output for the MAX6685 and is an open-drain, active-low output for the MAX6686. They are available in a space-saving 8-pin µMAX package.ApplicationsCPU Temperature ProtectionFan ControlFPGA Temperature ProtectionMultichip Modules