3 V to 5 V Single Supply, 200 kSPS, 12-Bit, Parallel Sampling ADC Features:Specified for VDD of 3 V to 5.5 V Read-Only Operation AD7854200 kSPS; AD7854L100 kSPS System and Self-Calibration Flexible Parallel Interface12-Bit Parallel/8-Bit Parallel (AD7854) 28-Lead DIP, SOIC and SSOP Packages (AD7854) Low Power:- Normal OperationAD7854: 15 mW (VDD = 3 V)AD7854L: 5.5 mW (VDD = 3 V)- Automatic Power-Down AfterConversion (25 W)AD7854: 1.3 mW 10 kSPSAD7854L: 650 W 10 kSPS

10-Bit, 100 MSPS+ TxDAC D/A Converter Features: Member of Pin-Compatible TxDAC Product Family 125 MSPS Update Rate 10-Bit Resolution Excellent Spurious Free Dynamic Range Performance SFDR to Nyquist @ 40 MHz Output: 52 dBc Differential Current Outputs: 2 ma to 20 mA Edge-Triggered Latches See datasheet for additional features

16-Bit 160 MSPS 2x/4x/8x Interpolating Dual TxDAC+ D/A Converter Features: 16-bit resolution, 160 MSPS/400 MSPS input/output data rate Selectable 2×/4×/8× interpolating filter Programmable channel gain and offset adjustment fS/4, fS/8 digital quadrature modulation capability Fully compatible SPI® port Direct IF transmission mode for 70 MHz + IFs Enables image rejection architecture See datasheet for additional features

Dual, 12-Bit, 1 GSPS, Digital-to-Analog Converter Features: Low power: 1.0 W @ 1 GSPS, 600 mW @ 500 MSPS, full operating conditions Single carrier W-CDMA ACLR = 80 dBc @ 80 MHz IF Analog output: adjustable 8.7 mA to 31.7 mA, RL = 25 Ω to 50 Ω Novel 2×, 4×, and 8× interpolator/coarse complex modulator allows carrier placement anywhere in DAC bandwidth Auxiliary DACs allow control of external VGA and offset control Multiple chip synchronization interface High performance, low noise PLL clock multiplier Digital inverse sinc filter 100-lead, exposed paddle TQFP

Broadband Modem Mixed-Signal Front End Features: Low cost, 3.3 V CMOS MxFE® for broadband modems 10-bit digital-to-analog converter (DAC) 2×/4× interpolation filter 250 MSPS DAC update rate 10-bit, 75 MSPS ADC Low noise RxPGA Dual channel muxed input 6 dB input overload attenuator −12 dB to +48 dB (without attenuator) Third-order programmable low-pass filter Flexible digital datapath interface Half-duplex and full-duplex operation Programmable delay Tx driver disable signal Various power-down/reduction modes Internal clock multiplier (PLL) 2 auxiliary programmable clock outputs 64-lead LFCSP

1 MSPS, 14-Bit, Simultaneous Sampling SAR ADC with PGA and Four Comparators Features: Dual, simultaneous sampling, 14-bit, 2-channel ADC True differential analog inputs Programmable gain stage: ×1, ×2, ×3, ×4, ×6, ×8, ×12, ×16, ×24, ×32, ×48, ×64, ×96, ×128 Throughput rate per ADC 1 MSPS for AD7264 Analog input impedance: >1 GΩ Wide input bandwidth −3 dB bandwidth: 1.7 MHz at gain = 2 4 on-chip comparators SNR: 78 dB typical at gain = 2, 71 dB typical at gain = 32 Device offset calibration System gain calibration On-chip reference: 2.5 V −40°C to +105°C operation High speed serial interface Compatible with SPI, QSPI™, MICROWIRE™, and DSP 48-lead LFCSP and LQFP packages

+3/+5 Volt Serial-Input Micropower 10-Bit DAC Features: Micropower - 100 µA Single Supply - 2.7 V to 5.5 V Operation Compact 1.75 mm Height SO-8 Package and 1.1 mm Height TSSOP-8 Package AD7390 - 12-Bit Resolution AD7391 - 10-Bit Resolution SPI and QSPI Serial Interface Compatible with Schmitt Trigger Inputs

20-Bit A/D Converter Features: Monolithic 16-Bit ADC 0.0015% Linearity Error On-Chip Self-Calibration Circuitry Programmable Low-Pass Filter 0.1 Hz to 10 Hz Corner Frequency 0 V to +2.5 V or 2.5 V Analog Input Range 4 kSPS Output Data Rate Flexible Serial Interface Ultralow Power

CMOS, 24-Bit Sigma-Delta, Signal Conditioning ADC with Matched RTD Excitation Currents Features: Charge-Balancing ADC 24 Bits, No Missing Codes ±0.0015% Nonlinearity 2-Channel Programmable Gain Front End Gains from 1 to 128 1 Differential Input 1 Single-Ended Input Low-Pass Filter with Programmable Filter Cutoffs Ability to Read/Write Calibration Coefficients RTD Excitation Current Sources Bidirectional Microcontroller Serial Interface Internal/External Reference Option Single- or Dual-Supply Operation Low Power (25 mW typ) with Power-Down Mode (7 mW typ)

10-Bit, 8-Channel, 350 kSPS, Serial A/D Converter Features: 10-Bit ADC with 2.3 µs Conversion Time The AD7812 has Eight Single-Ended Inputs that Can Be Configured as Seven Pseudo Differential Inputs with Respect to a Common, or as Four Independent Pseudo Differential Channels Onboard Track and Hold Onboard Reference 2.5 V ± 2.5% Operating Supply Range: 2.7 V to 5.5 V Specifications at 2.7 V-3.6 V and 5 V ± 10% DSP-/Microcontroller-Compatible Serial Interface High Speed Sampling and Automatic Power-Down Modes Package Address Pin on the AD7811 and AD7812 Allows Sharing of Serial Bus in Multipackage Applications Input Signal Range: 0 V to VREF Reference Input Range: 1.2 V to VDD