Precision Analog Microcontroller, 12-Bit Analog I/O, ARM7TDMI MCU with Enhanced IRQ Handler Features:Analog I/O Multichannel, 12-bit, 1 MSPS ADC Up to 12 ADC channels Fully differential and single-ended modes 0 V to VREF analog input range 12-bit voltage output DACs 4 DAC outputs available On-chip voltage reference On-chip temperature sensor Voltage comparatorMicrocontroller ARM7TDMI core, 16-bit/32-bit RISC architecture JTAG port supports code download and debugClocking options Trimmed on-chip oscillator (±3%) External watch crystal External clock source up to 44 MHz 41.78 MHz PLL with programmable divider Memory 62 kB Flash/EE memory, 8 kB SRAM In-circuit download, JTAG-based debug Software-triggered in-circuit reprogrammability Vectored interrupt controller for FIQ and IRQ 8 priority levels for each interrupt type Interrupt on edge or level external pin inputsOn-chip peripherals 2× fully I2C-compatible channels SPI (20 Mbps in master mode, 10 Mbps in slave mode) With 4-byte FIFO on input and output stages Up to 20 GPIO pins - Digital only GPIOs are 5 V tolerant 3× general-purpose timers Watchdog timer (WDT) Programmable logic array (PLA) 16 PLA elements 16-bit, 5-channel PWM

Integrated Precision Battery Sensor for Automotive Features:HIGH PRECISION ADCS Dual channel, simultaneous sampling, 16-bit, Σ-Δ ADCs Programmable ADC throughput from 1 Hz to 8 kHz On-chip 5 ppm/°C voltage reference Current channel Fully differential, buffered input Programmable gain from 1 to 512 ADC input range: −200 mV to +300 mV Digital comparators, with current accumulator feature Voltage channel Buffered, on-chip attenuator for 12 V battery inputs Temperature channel External and on-chip temperature sensor optionsMICROCONTROLLER ARM7TDMI® core, 16-/32-bit RISC architecture 20.48 MHz PLL with programmable divider PLL input source On-chip precision oscillator On-chip low power oscillator External (32.768 kHz) watch crystal JTAG port supports code download and debugMEMORY 96-kB Flash/EE memory, 6-kB SRAM 10,000-cycle Flash/EE endurance, 20-year Flash/EE retention In-circuit download via JTAG and LINON-CHIP PERIPHERALS SAEJ2602/LIN 1.3/LIN 2.0-compatible (slave) support via UART with hardware synchronization Flexible wake-up I/O pin, master/slave SPI® serial I/O 9-pin GPIO port, 3× general-purpose timers Wake-up and watchdog timers Power supply monitor, on-chip power-on-resetPOWER Operates directly from 12 V battery supply Current consumption Normal mode 10 mA at 10 MHz Low power monitor modePACKAGE AND TEMPERATURE RANGE 48-lead, 7 mm × 7 mm LFCSP Fully specified for −40°C to +115°C operation

Hot Swappable Dual I2C Isolator Features: Bidirectional I2C communication Open-drain interfaces Suitable for hot swap applications 30 mA current sink capability 1000 kHz operation 3.0 V to 5.5 V supply/logic levels 8-lead, RoHS compliant SOIC package See datasheet for additional features

3.75 kV, 6-Channel, SPIsolator Digital Isolator for SPI with Delay Clock Features: Supports up to 40 MHz SPI clock speed in delay clock mode Supports up to 17 MHz SPI clock speed in 4-wire mode 4 high speed, low propagation delay, SPI signal isolation channels 2 data channels at 250 kbps Delayed compensation clock line 20-lead SSOP with 5.1 mm creepage High temperature operation: 125°C High common-mode transient immunity: >25 kV/μs Safety and regulatory approvals UL recognition per UL 1577 3750 V rms for 1 minute CSA Component Acceptance Notice 5A VDE certificate of conformity DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 VIORM = 565 V peak

3.75 kV RMS Digital Isolators for Isolated USB 2.0 High, Full, and Low Speed Features: USB 2.0 signaling with automatic detection of low, full, and high speed connections 1.5 Mbps, 12 Mbps, and 480 Mbps data rates Bidirectional USB isolator for upstream and downstream ports Redriving and high speed data retiming for input jitter removal and an open eye Flexible clock input options 4.5 V to 5.5 V VBUSx or 3 V to 3.6V operation on each side 21 mA typical idle, low or full speed mode supply current 48 mA typical idle, high speed mode supply current Ultra low power standby in USB 2.0 suspend (L2) or disconnect 1.7 mA typical low power standby, upstream supply current 20 μA typical low power standby, downstream supply current ±6000 V IEC 61000-4-2 ESD protection across the isolation barrier Passed CISPR32/EN55032 Class B emissions High common-mode transient immunity: 50 kV/μs typical Safety and regulatory approvals (pending) UL (pending): 3750 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A (pending) IEC 62368-1, IEC 61010-1, and IEC60601-1 VDE certificate of conformity (pending) DIN V VDE V 0884-11 (VDE V 0884-11):2017-01 VIORM = 849 VPEAK (working voltage) Operating temperature range: −55°C to +125°C Compact 20-lead SSOP with 5.3 mm creepage and clearance

Isolated Switch Regulator with Integrated Feedback Features:Isolated PWM feedback with built in compensationPrimary side transformer driver for up to 2.5 W output power with 5 V input voltageRegulated adjustable output: 3.3 V to 24 VUp to 80% efficiency200 kHz to 1 MHz adjustable oscillatorSoft start function at power-upPulse-by-pulse overcurrent protectionThermal shutdown5000 V rms isolation High common-mode transient immunity: >25 kV/s16-lead SOIC package with 8.3 mm creepageHigh temperature operation: 105C

11 A High Voltage Isolated Bipolar Gate Driver with Fault Detection, Miller Clamp Features: 11 A short-circuit source current (0 Ω gate resistance) 9 A short-circuit sink current (0 Ω gate resistance) 4.61 A peak current (2 Ω gate resistance) Output power device resistance: <1 Ω Output voltage range up to 30 V Multiple UVLO options on VDD2 Grade A: 14.5 V (typical) UVLO on VDD2 positive going threshold Grade B and Grade C: 11.5 V (typical) UVLO on VDD2 positive going threshold VDD1 input voltage range from 2.5 V to 6 V Desaturation protection Soft shutdown on desaturation fault Multiple desaturation detect comparator voltages Grade B: 9.2 V (typical) Grade A and Grade C: 3.5 V (typical) Miller clamp output with gate sense input Isolated fault and ready functions Low propagation delay: 75 ns (typical) Operating temperature range: −40°C to +125°C Creepage distance: 8.3 mm minimum CMTI: 100 kV/μs Safety and regulatory approvals (pending) 5000 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A DIN V VDE V 0884-11 VIORM = 2150 V peak

Quad-Channel Isolators with Integrated DC-to-DC Converter (3:1 directionality) Features: isoPower integrated, isolated dc-to-dc converter 100 mA output supply AEC-Q100 qualified for automotive applications ADuM6421AW (ADuM6423AW pending) Meets CISPR 32/EN55032 Class B emission limits up to 5 Mbps at a full load on a 2-layer PCB Quad dc to 100 Mbps signal isolation channels 28-lead, fine pitch, SOIC with 8.3 mm minimum creepage High temperature operation: 125°C maximum High common-mode transient immunity: 100 kV/μs Safety and regulatory approvals (pending) UL recognition (pending) 5000 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A (pending) VDE V 0884-11 certificate of conformity (pending) VIORM = 566 V peak CQC certification per GB4943.1-2011 (pending)

Low Noise, Wide Bandwidth, MEMS Accelerometer Features: Single, in plane axis accelerometer with analog output Full-scale range: ±100 g Linear frequency response range: dc to 23 kHz typical (3 dB point) Resonant frequency: 42 kHz typical Ultralow noise density: 75 μg/√Hz Overrange sensing plus dc coupling allows fast recovery time Complete electromechanical self test Single-supply operation Output voltage ratiometric to supply Low power consumption: 1.0 mA typical Power saving standby operation mode with fast recovery RoHS compliant −40°C to +125°C operating temperature range 32-lead, 5 mm × 5 mm × 1.80 mm LFCSP package See datasheet for additional features

200 g Range, 3-Axis Digital Accelerometer Features: ±200 g measurement range Low power: 170 μA in measurement mode and 17 μA in standby mode at VS = 2.5 V (typical) User selectable bandwidth up to 3200 Hz ODR Fixed 13-bit output resolution Supply voltage range: 2.0 V to 3.6 V Embedded memory management system with FIFO technology minimizes host processor load Shock event detection Activity/inactivity monitoring SPI (3- or 4-wire) and I2C digital interfaces Wide temperature range: −40 to +125°C 10,000 g shock survival Pb free and RoHS compliant Small and thin: 32-lead, 5 mm × 5 mm × 1.45 mm LFCSP AEC-Q100 qualified for automotive applications