12-Bit Power Amplifier Current Controller with ADC, DACs, Temperature and Current Sensors Features: 4 closed-loop power amplifier (PA) drain current controllers Built-in PA protection, sequencing, and alert features Compatible with both depletion mode and enhancement mode power amplifiers Highly integrated 4 uncommitted 12-bit analog-to-digital converter (ADC) inputs ±0.5 LSB typical integral nonlinearity (INL) Eight 12-bit voltage digital-to-analog converters (DACs) 1.3 μs maximum settling 4 high-side current sense amplifiers, ±0.1% gain error 2 external temperature sensor inputs, ±1.1°C accuracy Internal temperature sensor, ±1.25°C accuracy 2.5 V on-chip reference Flexible monitoring and control ranges ADC input ranges: 0 V to 1.25 V, 0 V to 2.5 V, and 0 V to 5 V Bipolar DAC ranges: 0 V to +5 V, −4 V to +1 V, and −5 V to 0 V Bipolar DAC reset and clamping relative to VCLAMPx voltage Unipolar DAC ranges: 0 V to 5 V, 2.5 V to 7.5 V, and 5 V to 10 V Current sense gain: 6.25, 12.5, 25, 50, 100, and more Adjustable closed-loop setpoint ramp time High-side voltage current sensing 4 current sense inputs 4 V to AVSS + 60 V, ±200 mV input range Small package and flexible interface Serial port interface (SPI) with VDRIVE supporting 1.8 V, 3 V, and 5 V interfaces 56-lead LFCSP Temperature range: −40°C to +125°C

16-Bit, Isolated Sigma-Delta Modulator, LVDS Interface Features: 5 MHz to 20 MHz external clock input rate 16 bits, no missing codes Signal-to-noise ratio (SNR): 88 dB typical Effective number of bits (ENOB): 14.2 bits typical Typical offset drift vs. temperature: 1.6 μV/°C typical LVDS interface On-board digital isolator On-board reference Full-scale analog input range: ±320 mV −40°C to + 125°C operating range High common-mode transient immunity: >25 kV/μs 16-lead, wide-body SOIC, with increased creepage package See data sheet for additional features

4-Channel DAS with 16-Bit, Bipolar Input, Simultaneous Sampling ADC Features: 4 simultaneously sampled inputs True bipolar analog input ranges: ±10 V (maximum), ±5 V (maximum) Single 5 V analog supply and 2.5 V to 5 V VDRIVE (nominal) Fully integrated data acquisition solution Analog input clamp protection Input buffer with 1 MΩ analog input impedance Second-order antialiasing analog filter On-chip accurate reference and reference buffer 16-bit ADC with 300 kSPS on all channels Flexible parallel/serial interface Serial peripheral interface (SPI)/QSPI™/MICROWIRE™/DSP compatible Performance 7 kV ESD rating on analog input channels Standby mode: 25 mW (typical) 64-lead LQFP package

8-Channel DAS with 16-Bit, Bipolar Input, Simultaneous Sampling ADC Features: 8/6/4 simultaneously sampled inputs True bipolar analog input ranges: ±10 V, ±5 V Pin to pin compatible with the state-of-the-art AD7606B Single 5 V analog supply and 2.3 V to 5 V VDRIVE Fully integrated data acquisition solution Analog input clamp protection Input buffer with 1 MΩ analog input impedance Second-order antialiasing analog filter On-chip accurate reference and reference buffer 16-bit ADC with 200 kSPS on all channels Oversampling capability with digital filter Flexible parallel/serial interface SPI/QSPI™/MICROWIRE™/DSP compatible Performance 7 kV ESD rating on analog input channels 95.5 dB SNR, −107 dB THD ±0.5 LSB INL, ±0.5 LSB DNL Low power: 100 mW Standby mode: 25 mW Temperature range: −40°C to +85°C 64-lead LQFP packageAD7606-EP supports defense and aerospace applications (AQEC standard) Download AD7606-EP data sheet (pdf) Military temperature range −55°C to +125°C Controlled manufacturing baseline One assembly/test site One fabrication site Product change notification Qualification data available on request V62/18611

Triple Output Power Supply for Small TFT-LCD Displays Features: Generates Three Voltages: 5.1V at 10mA 5V, -10V, or -15V at 500µA 10V or 15V at 500µA Better than 90% Efficiency Low Output Ripple: Less than 5mVP-P Complete 1mm Component Profile Solution Controlled Power-Up Sequence: AVDD/VGL/VGH All Outputs Disconnected and Actively Discharged in Shutdown Low Noise Fixed Frequency Operation Frequency Reduction Input for High Efficiency in Blank Mode Ultralow Quiescent Current: 75µA (Typ) in Scan Mode Available in a 3mm × 3mm 16-Pin QFN Package

3-Phase, 600kHz, Synchronous Buck Switching Regulator Controller Features: 3-Phase Current Mode Controller with Onboard MOSFET Drivers ±5% Output Current Matching Optimizes Thermal Performance and Size of Inductors and MOSFETs Differential Amplifier Accurately Senses VOUT ±1% VREF Accuracy Over Temperature VOUT Range: 0.6V to 5.5V without Diffamp VOUT Range: 0.6V to (VCC – 1.2V) with Diffamp 250kHz to 600kHz Per Phase, PLL, Fixed Frequency PWM, Stage Shedding™ or Burst Mode® Operation OPTI-LOOP® Compensation Minimizes COUT Adjustable Soft-Start Current Ramping Short-Circuit Shutdown Timer with Defeat Option Overvoltage Soft Latch Adjustable Undervoltage Lockout Threshold Selectable Phase Output for Up to 12-Phase Operation Available in 5mm × 5mm QFN and 36-Pin Narrow (0.209') SSOP Packages

Single/Dual Power Supply Margining Controller Features: Margin Voltage Precision <0.4% 400:1 Current Programming Range Symmetric/Asymmetric High and Low Voltage Margining Single Control Pin per Supply-High, Float, Low Single Current Setting Resistor per Supply Wide VCC Compliance 2.3V < VCC < 6V Wide Output Compliance 0.6V < VMARGIN < (VCC - 0.6V) Single in 5-Pin ThinSOT™ (LTC2920-1) Dual in 8-Pin MSOP (LTC2920-2)

Digitally Controlled Programmable Gain Amplifiers in SOT-23 Features: 3-Bit Digital Gain Control in Three Gain-Code Options Rail-to-Rail Input Range Rail-to-Rail Output Swing Single or Dual Supply: 2.7V to 10.5V Total 11MHz Gain Bandwidth Product Input Noise Down to 8nV/√Hz System Dynamic Range to 120dB Input Offset Voltage: 1.5mV 8-Pin Low Profile (1mm) SOT-23 (ThinSOT™) Package

Standalone Linear Li-Ion Battery Charger with Thermal Regulation in ThinSOT Features: Programmable Charge Current Up to 800mA No MOSFET, Sense Resistor or Blocking Diode Required Complete Linear Charger in ThinSOT™ Package for Single Cell Lithium-Ion Batteries Constant-Current/Constant-Voltage Operation with Thermal Regulation* to Maximize Charge Rate Without Risk of Overheating Charges Single Cell Li-Ion Batteries Directly from USB Port Preset 4.2V Charge Voltage with ±1% Accuracy Charge Current Monitor Output for Gas Gauging* Automatic Recharge Charge Status Output Pin C/10 Charge Termination 25µA Supply Current in Shutdown 2.9V Trickle Charge Threshold (LTC4054) Available Without Trickle Charge (LTC4054X) Soft-Start Limits Inrush Current Available in 5-Lead SOT-23 Package

High Voltage 3A, 500kHz Step-Down Switching Regulator with 100A Quiescent Current Features: Wide Input Range: 3.3V to 60V 3A Peak Switch Current Burst Mode® Operation: 100µA Quiescent Current Low Shutdown Current: IQ < 1µA Power Good Flag with Programmable Threshold Load Dump Protection to 60V 500kHz Switching Frequency Saturating Switch Design: 0.1Ω On-Resistance Peak Switch Current Maintained Over Full Duty Cycle Range 1.25V Feedback Reference Voltage Easily Synchronizable Soft-Start Capability Small 16-Pin Thermally Enhanced TSSOP Package