The AD5241 / AD52421 provide a single-/dual-channel, 256-position, digitally controlled variable resistor (VR) device. These devices perform the same electronic adjustment function as a potentiometer, trimmer, or variable resistor. Each VR offers a completely programmable value of resistance between the A terminal and the wiper, or the B terminal and the wiper. For the AD5242, the fixed A-to-B terminal resistance of 10 kΩ, 100 kΩ, or 1 MΩ has a 1% channel-to-channel matching tolerance. The nominal temperature coefficient of both parts is 30 ppm/°C.Wiper position programming defaults to midscale at system power on. When powered, the VR wiper position is programmed by an I2C-compatible, 2-wire serial data interface. Both parts have two extra programmable logic outputs available that enable users to drive digital loads, logic gates, LED drivers, and analog switches in their system.The AD5241 / AD5242 are available in surface-mount, 14-lead SOIC and 16-lead SOIC packages and, for ultracompact solutions, 14-lead TSSOP and 16-lead TSSOP packages. All parts are guaranteed to operate over the extended temperature range of −40°C to +105°C.APPLICATIONS Multimedia, video, and audio Communications Mechanical potentiometer replacement Instrumentation: gain, offset adjustment Programmable voltage-to-current conversion Line impedance matching

The AD5243 and AD5248 provide a compact 3 mm × 4.9 mmpackaged solution for dual, 256-position adjustment applications.The AD5243 performs the same electronic adjustment functionas a 3-terminal mechanical potentiometer, and the AD5248performs the same adjustment function as a 2-terminal variableresistor. Available in four end-to-end resistance values (2.5 kΩ,10 kΩ, 50 kΩ, and 100 kΩ), these low temperature coefficientdevices are ideal for high accuracy and stability-variableresistance adjustments. The wiper settings are controllablethrough the I2C-compatible digital interface. The AD5248 hasextra package address decode pins, AD0 and AD1, allowingmultiple parts to share the same I2C, 2-wire bus on a PCB. Theresistance between the wiper and either endpoint of the fixedresistor varies linearly with respect to the digital code transferred into the RDAC latch. (The terms digital potentiometer, VR,and RDAC are used interchangeably.)Operating from a 2.7 V to 5.5 V power supply and consumingless than 6 µA allows the AD5243/AD5248 to be used inportable battery-operated applications.For applications that program the AD5243/AD5248 at thefactory, Analog Devices, Inc., offers device programmingsoftware running on Windows® NT/2000/XP operating systems.This software effectively replaces the need for external I2Ccontrollers, which in turn enhances the time to market ofsystems. An AD5243/AD5248 evaluation kit and software areavailable. The kit includes a cable and instruction manual.Applications Systems calibrations Electronics level settings Mechanical trimmers replacement in new designs Permanent factory printed circuit board (PCB) setting Transducer adjustment of pressure, temperature, position, chemical, and optical sensors RF amplifier biasing Gain control and offset adjustment

The AD5243 and AD5248 provide a compact 3 mm × 4.9 mmpackaged solution for dual, 256-position adjustment applications.The AD5243 performs the same electronic adjustment functionas a 3-terminal mechanical potentiometer, and the AD5248performs the same adjustment function as a 2-terminal variableresistor. Available in four end-to-end resistance values (2.5 kΩ,10 kΩ, 50 kΩ, and 100 kΩ), these low temperature coefficientdevices are ideal for high accuracy and stability-variableresistance adjustments. The wiper settings are controllablethrough the I2C-compatible digital interface. The AD5248 hasextra package address decode pins, AD0 and AD1, allowingmultiple parts to share the same I2C, 2-wire bus on a PCB. Theresistance between the wiper and either endpoint of the fixedresistor varies linearly with respect to the digital code transferred into the RDAC latch. (The terms digital potentiometer, VR,and RDAC are used interchangeably.)Operating from a 2.7 V to 5.5 V power supply and consumingless than 6 µA allows the AD5243/AD5248 to be used inportable battery-operated applications.For applications that program the AD5243/AD5248 at thefactory, Analog Devices, Inc., offers device programmingsoftware running on Windows® NT/2000/XP operating systems.This software effectively replaces the need for external I2Ccontrollers, which in turn enhances the time to market ofsystems. An AD5243/AD5248 evaluation kit and software areavailable. The kit includes a cable and instruction manual.Applications Systems calibrations Electronics level settings Mechanical trimmers replacement in new designs Permanent factory printed circuit board (PCB) setting Transducer adjustment of pressure, temperature, position, chemical, and optical sensors RF amplifier biasing Gain control and offset adjustment

The AD5243 and AD5248 provide a compact 3 mm × 4.9 mmpackaged solution for dual, 256-position adjustment applications.The AD5243 performs the same electronic adjustment functionas a 3-terminal mechanical potentiometer, and the AD5248performs the same adjustment function as a 2-terminal variableresistor. Available in four end-to-end resistance values (2.5 kΩ,10 kΩ, 50 kΩ, and 100 kΩ), these low temperature coefficientdevices are ideal for high accuracy and stability-variableresistance adjustments. The wiper settings are controllablethrough the I2C-compatible digital interface. The AD5248 hasextra package address decode pins, AD0 and AD1, allowingmultiple parts to share the same I2C, 2-wire bus on a PCB. Theresistance between the wiper and either endpoint of the fixedresistor varies linearly with respect to the digital code transferred into the RDAC latch. (The terms digital potentiometer, VR,and RDAC are used interchangeably.)Operating from a 2.7 V to 5.5 V power supply and consumingless than 6 µA allows the AD5243/AD5248 to be used inportable battery-operated applications.For applications that program the AD5243/AD5248 at thefactory, Analog Devices, Inc., offers device programmingsoftware running on Windows® NT/2000/XP operating systems.This software effectively replaces the need for external I2Ccontrollers, which in turn enhances the time to market ofsystems. An AD5243/AD5248 evaluation kit and software areavailable. The kit includes a cable and instruction manual.Applications Systems calibrations Electronics level settings Mechanical trimmers replacement in new designs Permanent factory printed circuit board (PCB) setting Transducer adjustment of pressure, temperature, position, chemical, and optical sensors RF amplifier biasing Gain control and offset adjustment

The ADM3483E / ADM3486E / ADM3488E / ADM3490E / ADM3491E are 3.3 V low power data transceivers with ±15 kV ESD protection suitable for full and half-duplex communication on multipoint bus transmission lines. They are designed for balanced data transmission and comply with TIA/EIA standards RS-485 and RS-422. The ADM3483E / ADM3486E are half-duplex transceiver that shares differential lines and has separate enable inputs for the driver and receiver. The full-duplex ADM3488E / ADM3490E / ADM3491E transceivers have dedicated differential line driver outputs and receiver inputs. The ADM3491E also features enable inputs for the driver and receiver.The devices have a 12 kΩ receiver input impedance which allows up to 32 transceivers on a bus. Since only one driver should be enabled at any time, the output of a disabled or powered down driver is three-stated to avoid overloading the bus. The driver outputs of the ADM3483E / ADM3486E / ADM3488E are slew rate limited, in order to reduce EMI and data errors caused by reflections from improperly terminated buses. The receiver has a fail-safe feature that ensures a logic high output when the inputs are floating.Excessive power dissipation caused by bus contention or by output shorting is prevented with a thermal shutdown circuit. The parts are fully specified over the commercial and industrial temperature ranges and are available in narrow 8-lead and 14-lead (ADM3491E) SOIC packages.

The ADM3483E / ADM3486E / ADM3488E / ADM3490E / ADM3491E are 3.3 V low power data transceivers with ±15 kV ESD protection suitable for full and half-duplex communication on multipoint bus transmission lines. They are designed for balanced data transmission and comply with TIA/EIA standards RS-485 and RS-422. The ADM3483E / ADM3486E are half-duplex transceiver that shares differential lines and has separate enable inputs for the driver and receiver. The full-duplex ADM3488E / ADM3490E / ADM3491E transceivers have dedicated differential line driver outputs and receiver inputs. The ADM3491E also features enable inputs for the driver and receiver.The devices have a 12 kΩ receiver input impedance which allows up to 32 transceivers on a bus. Since only one driver should be enabled at any time, the output of a disabled or powered down driver is three-stated to avoid overloading the bus. The driver outputs of the ADM3483E / ADM3486E / ADM3488E are slew rate limited, in order to reduce EMI and data errors caused by reflections from improperly terminated buses. The receiver has a fail-safe feature that ensures a logic high output when the inputs are floating.Excessive power dissipation caused by bus contention or by output shorting is prevented with a thermal shutdown circuit. The parts are fully specified over the commercial and industrial temperature ranges and are available in narrow 8-lead and 14-lead (ADM3491E) SOIC packages.

The ADM3491 is a low power differential line transceiver designed to operate using a single +3.3 V power supply. Low power consumption coupled with a shutdown mode make it ideal for power sensitive applications. It is suitable for communication on multipoint bus transmission lines.

The ADM3483E / ADM3486E / ADM3488E / ADM3490E / ADM3491E are 3.3 V low power data transceivers with ±15 kV ESD protection suitable for full andhalf-duplex communication on multipoint bus transmission lines. They are designed for balanced data transmission and comply with TIA/EIA standards RS-485 and RS-422. The ADM3483E / ADM3486E is a half-duplex transceiver that shares differential lines and has separate enable inputs for the driver and receiver. The full-duplex ADM3488E / ADM3490E / ADM3491E transceivers have dedicated differential line driver outputs and receiver inputs. The ADM3491E also features enable inputs for the driver and receiver.The devices have a 12 kΩ receiver input impedance which allows up to 32 transceivers on a bus. Since only one driver should be enabled at any time, the output of a disabled or powered down driver is three-stated to avoid overloading the bus. The driver outputs of the ADM3483E / ADM3486E / ADM3488E are slew rate limited in order to reduce EMI and data errors caused by reflections from improperly terminated buses. The receiver has a failsafe feature which ensures a logic high output when the inputs are floating. Excessive power dissipation caused by bus contention or by output shorting is prevented with a thermal shutdown circuit. The parts are fully specified over the industrialtemperature ranges and are available in narrow 8-lead and 14-lead (ADM3491E) SOIC packages.

The ADM3483E / ADM3486E / ADM3488E / ADM3490E / ADM3491E are 3.3 V low power data transceivers with ±15 kV ESD protection suitable for full andhalf-duplex communication on multipoint bus transmission lines. They are designed for balanced data transmission and comply with TIA/EIA standards RS-485 and RS-422. The ADM3483E / ADM3486E is a half-duplex transceiver that shares differential lines and has separate enable inputs for the driver and receiver. The full-duplex ADM3488E / ADM3490E / ADM3491E transceivers have dedicated differential line driver outputs and receiver inputs. The ADM3491E also features enable inputs for the driver and receiver.The devices have a 12 kΩ receiver input impedance which allows up to 32 transceivers on a bus. Since only one driver should be enabled at any time, the output of a disabled or powered down driver is three-stated to avoid overloading the bus. The driver outputs of the ADM3483E / ADM3486E / ADM3488E are slew rate limited in order to reduce EMI and data errors caused by reflections from improperly terminated buses. The receiver has a failsafe feature which ensures a logic high output when the inputs are floating. Excessive power dissipation caused by bus contention or by output shorting is prevented with a thermal shutdown circuit. The parts are fully specified over the industrialtemperature ranges and are available in narrow 8-lead and 14-lead (ADM3491E) SOIC packages.

The ADM560 / ADM561 are four driver/five receiver interface devices designed to meet the EIA-232 standard while operating with a single +3.3 V power supply. The devices feature an on-board dc-to-dc converter, eliminating the need for dual ±5 V power supplies. This dc-dc converter contains a voltage doubler and voltage inverter which internally generates ±6.6 V from the input +3.3 V power supply.The ADM560 and ADM561 consume only 5 mW making them ideally suited for battery and other power-sensitive applications. A shutdown facility is also provided which reduces the power to 0.66 µW.The ADM560 contains active low shutdown and active high receiver enable signals. In shutdown mode, two receivers remain active thereby allowing monitoring of peripheral devices. This feature allows the device to be shut down until a peripheral device begins communication. The active receivers can alert the processor which can then take the ADM560 out of the shutdown mode.The ADM561 features active high shutdown and an active low receiver enable. In this device all receivers are disabled in shutdown.The ADM560 / ADM561 is fabricated using CMOS technology for minimal power consumption. It features a high level of over-voltage protection and latch-up immunity. The receiver inputs can withstand up to ±25 V levels. The transmitter inputs can be driven from either 3V or 5V logic levels. This allows operation in mixed 3 V/5 V power supply systems.The ADM560 / ADM561 is packaged in a 28-pin SO and a 28-pin SSOP package.APPLICATIONS Notebook computers Peripherals Modems Printers Battery-operated equipment