1kHz to 33MHz Resistor Set SOT-23 Oscillator Features: One External Resistor Sets the Frequency Fast Start-Up Time: <1ms 1kHz to 33MHz Frequency Range Frequency Error ≤1.5% 5kHz to 20MHz (TA = 25°C) Frequency Error ≤2% 5kHz to 20MHz (TA = 0°C to 70°C) ±40ppm/°C Temperature Stability 0.05%/V Supply Stability 50% ±1% Duty Cycle 1kHz to 2MHz 50% ±5% Duty Cycle 2MHz to 20MHz 1mA Typical Supply Current 100Ω CMOS Output Driver Operates from a Single 2.7V to 5.5V Supply Low Profile (1mm) SOT-23 (ThinSOT™ Package) AEC-Q100 Qualified for Automotive Applications

20dB Gain Block, 50 IF Amplifier Features: 50Ω Matched 20MHz to 1400MHz 20.8dB Power Gain 46.2dBm OIP3 at 240MHz Into 50Ω NF = 2.6dB at 240MHz 0.6nV/√Hz Total Input Noise S11 < –10dB Up to 2.0GHz S22 < –10dB Up to 1.4GHz >2.0VP-P Linear Output Swing P1dB = 22.0dBm 50Ω Single-Ended Input/Output Insensitive to VCC Variation A-Grade 100% OIP3 Tested at 240MHz Input/Output Internally Matched to 50Ω Single 5V Supply

60V Synchronous 4-Switch Buck-Boost Controller Features: 4-Switch Single Inductor Architecture Allows VIN Above, Below or Equal to VOUT Synchronous Switching: Up to 98.5% Efficiency Wide VIN Range: 4.7V to 60V 2% Output Voltage Accuracy: 1.2V ≤ VOUT < 60V 6% Output Current Accuracy: 0V ≤ VOUT < 60V Input and Output Current Regulation with Current Monitor Outputs No Top FET Refresh in Buck or Boost VOUT Disconnected from VIN During Shutdown C/10 Charge Termination and Output Shorted Flags Capable of 100W or Greater per IC Easy Parallel Capability to Extend Output Power 38-Lead TSSOP with Exposed Pad

100MHz to 40GHz Linear-in-dB RMS Power Detector with 35dB Dynamic Range Features: Ultra Wide Matched Input Frequency Range: 100MHz to 40GHz 35dB Linear Dynamic Range (< ±1dB Error) 29mV/dB Logarithmic Slope ±1dB Flat Response from 200MHz to 30GHz Accurate RMS Power Measurement of High Crest Factors (Up to 12dB) Modulated Waveforms Low Power Shutdown Mode Low Supply Current: 30mA at 3.3V (Typical) Small 2mm × 2mm Plastic DFN8 Package I-Grade: –40°C to 105°C Rated H-Grade: –40°C to 125°C Rated with Guaranteed Log-Slope and Log-Intercept ESD Rating: 3500V HBM, 1500V CDM

Dual Ultrathin 2.5A or Single 5A Step-Down DC/DC Module Regulator Features: Complete Solution in <1cm2 Wide Input Voltage Range:3.6V to 20V 3.3V Input Compatible with VIN Tied to INTVCC 0.6V to 5.5V Output Voltage Dual 2.5A (3A Peak) or Single 5A Output Current ±1.5% Maximum Total Output Voltage Regulation Error Over Load, Line and Temperature Current Mode Control, Fast Transient Response External Frequency Synchronization Multiphase Parallelable with Current Sharing Output Voltage Tracking and Soft-Start Capability Selectable Burst Mode® Operation Overvoltage Input and Overtemperature Protection Power Good Indicators 6.25mm × 6.25mm × 1.82mm LGA and 6.25mm × 6.25mm × 2.42mm BGA Packages

Active Clamp Synchronous Forward Controller Features: Input Voltage Range: 8.5V to 100V Programmable Volt-Second Clamp High Efficiency Control: Active Clamp, Synchronous Rectification, Programmable Delays Short-Circuit (Hiccup Mode) Overcurrent Protection Programmable Soft-Start/Stop Programmable OVLO and UVLO with Hysteresis Programmable Frequency (100kHz to 500kHz) Synchronizable to an External Clock

16-Bit, 50Msps DAC Features: 50Msps Update Rate Pin Compatible 12-Bit, 14-Bit and 16-Bit Devices High Spectral Purity: 87dB SFDR at 1MHz fOUT 5pV-s Glitch Impulse Differential Current Outputs 20ns Settling Time Low Power: 180mW from ±5V Supplies TTL/CMOS (3.3V or 5V) Inputs Small Package: 28-Pin SSOP

Low IQ Boost/SEPIC/Inverting Converter with 2A, 60V Switch Features: Wide Input Voltage Range: 2.8V to 60V Ultralow Quiescent Current and Low Ripple Burst Mode® Operation: IQ = 9µA 2A, 60V Power Switch Positive or Negative Output Voltage Programming with a Single Feedback Pin Programmable Frequency (300kHz to 2MHz) Synchronizable to an External Clock Spread Spectrum Frequency Modulation for Low EMI BIAS Pin for Higher Efficiency Programmable Undervoltage Lockout (UVLO) Thermally Enhanced 10-lead 3mm × 3mm DFN and 16-lead MSOP packages AEC-Q100 Qualified for Automotive Applications

35V/3.2A Multi-Cell Lithium-Ion Step-Down Battery Charger with PowerPath and I2C Telemetry Features: Li-Ion/Polymer Battery Charger with Termination Wide Charging Input Voltage Range: 4.5V to 35V High Efficiency Synchronous Operation 16-Bit Digital Telemetry System Monitors VBAT, IBAT, RBAT, TBAT, TDIE, VIN, IIN, VOUT Charges 1-8 Lithium-Ion/Polymer Cells Input Undervoltage Charge Current Limit Loop Input MPPT for Solar Panel Inputs Input Current Limit Prioritizes System Load Output Low Loss PowerPath™ Instant-On Operation with Discharged or Missing Battery JEITA Temperature Controlled Charging Pin Compatible with LiFePO4 and SLA Versions

Low Quiescent Current eFuse with Surge Protection Features: Withstands Surge Voltages Up to 100V Internal 9mΩ N-Channel MOSFET Guaranteed Safe Operating Area: 20ms at 70V, 1A Low Quiescent Current: 6μA Operating Operates Through Automobile Cold Crank Wide Operating Voltage Range: 4V to 72V No Input TVS Needed Overcurrent Protection Selectable Internal 28.5V/47V or Adjustable Output Clamp Voltage Reverse Input Protection to –60V Adjustable Turn-On Threshold Adjustable Fault Timer with MOSFET Stress Acceleration Latchoff and Retry Options Low Retry Duty Cycle During Faults 32-Lead DFN (7mm × 5mm) Package