18V, 5A Synchronous Buck-Boost DC/DC Converter Features:Input Voltage Range: 2.5V to 18VRuns Down to VIN = 250mV After Start-UpOutput Voltage Range: 0.8V to 18V5A Output Current in Buck Mode, VIN > 6V3A Output Current for VIN = 3.6V, VOUT = 5VProgrammable Switching Frequency: 400kHz to 2MHzSynchronizable with an External Clock Up to 2MHzAccurate Run Comparator ThresholdBurst Mode® Operation, No-Load IQ = 35μAUltralow Noise Buck-Boost PWMCurrent Mode ControlMaximum Power Point ControlPower Good IndicatorInternal Soft-Start28-Lead 4mm × 5mm QFN and TSSOP Packages

55V Buck-Boost Multi-Chemistry Battery Charger Features: Wide Voltage Range: 4.5V to 55V Input, Up to 55V Output (60V Absolute Maximums) Synchronous Buck-Boost DC/DC Controller Li-Ion and Lead-Acid Charge Algorithms ±0.5% Float Voltage Accuracy ±5% Charge Current Accuracy Instant-On for Heavily Discharged Batteries Ideal Diode Controller Provides Low Loss PowerPath When Input Power is Limited Input Voltage Regulation for High Impedance Input Supplies and Solar Panel Peak Power Operation Onboard Timer for Protection and Termination Bad Battery Detection with Auto-Reset NTC Input for Temperature Qualified Charging Binary Coded Open-Collector Status Pins Low Profile (0.75mm) 38-Pin 5mm × 7mm QFN Package

Dual 42V Synchronous Monolithic Step-Down Regulator with 6.5A Quiescent Current Features: Wide Input Voltage Range: 3.4V to 42V 2.5A and 1.5A Buck Regulators with Separate Inputs Fast Minimum Switch On-Time: 35ns Ultralow Quiescent Current Burst Mode® Operation: 6.5μA IQ Regulating 12VIN to 5VOUT and 3.3VOUT Output Ripple < 15mV 180° Out of Phase Switching Adjustable: 200kHz to 3MHz Synchronizable: 250kHz to 3MHz Accurate 1V Enable Pin Thresholds Internal Compensation Output Soft-Start and Tracking TSSOP Package: Output Stays at or Below Regulation Voltage During Adjacent Pin Short or When a Pin Is Left Floating Thermally Enhanced 28-Lead TSSOP and 3mm × 6mm QFN Packages

2 GHz to 18 GHz, Digitally Tunable, High-Pass and Low-Pass Filter Features: Digitally tunable, multioctave, high-pass and low-pass tuning Independent 3 dB frequency control for up to 4 GHz of bandwidth Optimal wideband rejection: 35 dB Single chip replacement for discrete filter banks Compact 9 mm × 9 mm, 56-terminal LGA packageENHANCED PRODUCT FEATURES Supports defense and aerospace applications (AQEC standard Military temperature range of −55°C to +105°C Controlled manufacturing baseline One assembly and test site One fabrication site Production change notification Qualification data available on request V62/21604

5.7 kV RMS/1.5 kV RMS, Quad-Channel LVDS 2.5 Gigabit Isolator (0 Reverse Channels) Features: 5.7 kV rms and 1.5 kV rms LVDS isolators Complies with TIA/EIA-644-A LVDS signal levels Quad-channel configuration Any data rate up to 2.5 Gbps switching with low jitter 10 Gbps total bandwidth across four channels 2.15 ns typical propagation delay Typical jitter: 0.82 ps rms random, 40 ps total peak Lower power 1.8 V supplies ±8 kV IEC 61000-4-2 ESD protection across isolation barrier High common-mode transient immunity: 100 kV/μs typical Safety and regulatory approvals (28-lead SOIC_W_FP package) UL (pending): 5700 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A (pending) VDE certificate of conformity (pending) DIN V VDE V 0884-11 (VDE V 0884-11):2017-01 VIORM = 849 VPEAK (working voltage) Enable or disable refresh (low speed output correctness check) Operating temperature range: −40°C to +125°C 28-lead, wide-body, finer pitch SOIC_W_FP package with 8.3 mm creepage and clearance or 6 mm × 6 mm LFCSP package with 1.27 mm creepage and clearance

5 kV RMS/3.75 kV RMS, Dual LVDS Gigabit Isolator (0 Reverse Channels) Features: 5 kV rms and 3.75 kV rms LVDS isolators Complies with TIA/EIA-644-A LVDS standard Multiple dual-channel configurations Any data rate up to 1.1 Gbps switching with low jitter 4 ns typical propagation delay 2.6 ps rms typical random jitter, rms 90 ps typical peak-to-peak total jitter at 1.1 Gbps 2.5 V or 3.3 V supplies −75 dBc power supply ripple rejection, phase spur level Glitch immunity ±8 kV IEC 61000-4-2 ESD protection across isolation barrier High common-mode transient immunity: >25 kV/μs Passes EN 55022 Class B radiated emissions limits with 1.1 Gbps PRBS Safety and regulatory approvals (20-lead SOIC_W package) UL (pending): 5000 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A (pending) VDE certificate of conformity (pending) DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 VIORM = 424 VPEAK Fail-safe output high for open, short, and terminated input conditions (ADN4655/ADN4656) Operating temperature range: −40°C to +125°C 7.8 mm minimum creepage and clearance

Three-Channel, Isolated Micropower Management Unit with Seven Digital Isolators Features: Wide input supply voltage range: 4.5 V to 60 V Integrated flyback power switch Generates isolated, independent bipolar outputs and factory programmable buck output VOUT1: 21 V, 24 V or 6 V to 28 V VOUT2: 5.15 V, 5.0 V, or 3.3 V VOUT3: −24 V to −5 V Uses a 1:1 ratio transformer for simplified transformer design Peak current limiting and OVP for flyback, buck, and inverting regulators Precision enable input and power-good output Adjustable switching frequency via SYNC input Internal compensation and soft start control per regulator High speed, low propagation delay, SPI signal isolation channels Three, 100 kbps general-purpose isolated data channels 9 mm × 7 mm LFCSP form factor enables small overall solution size −40°C to +125°C operating junction temperature range Conforms to CISPR11 Class B radiated emission limits Safety and regulatory approvals (pending) UL recognition: 2500 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A 300 V rms basic insulation between slave, master, and field power domains (IEC 61010-1, pending) VDE certificate of conformity DIN V VDE 0884-10 (VDE 0884-10):2006-12 VIORM = 565 VPEAK

Two-Channel, Isolated Micropower Management Unit with Seven Digital Isolators Features: Wide input supply voltage range: 4.5 V to 60 V Integrated flyback power switch Generates two isolated, well regulated independent outputs VOUT1: 24 V or 6 V to 28 V VOUT2: 3.3 V, 5.0 V, or 5.15 V Uses a 1:1 ratio transformer for simplified transformer design Peak current limiting and OVP for flyback and buck regulators Precision enable input and power-good output Adjustable switching frequency via SYNC input Internal compensation and soft start control per regulator High speed, low propagation delay, SPI signal isolation channels Three 100 kbps general-purpose isolated data channels 41-lead, 9 mm × 7 mm LFCSP form factor enables small overall solution size −40°C to +125°C operating junction temperature range Safety and regulatory approvals (pending) CISPR11 Class B radiated emission UL recognition: 2500 V rms for 1 minute duration per UL 1577 CSA Component Acceptance Notice 5A 300 V rms basic insulation between slave, master, and field power domains (IEC 61010-1, pending) VDE certificate of conformity DIN V VDE 0884-10 (VDE 0884-10):2006-12 VIORM = 565 VPEAK

Digital Controller for Power Supply Applications with PMBus Interface Features: −40°C to +125°C operation with EEPROM data retention of 15 years at 125°C PMBus Revision 1.2 compliant 32-bit password protection with command masking 64 address selections (16 base addresses, expandable to 64) 6 PWM control signals, 625 ps resolution Duty cycle double update rate Digital control loop (PID + additional pole or zero configurability) Programmable loop filters (CCM, DCM, low/normal temperature) Frequency synchronization Soft start and soft stop functionality Average and peak constant current mode External PN junction temperature sensing 4 GPIOs (2 GPIOs configurable as active clamp snubber PWMs) Fast line voltage feedforward Adaptive dead time compensation for improved efficiency Extended black box data recorder for fault recording See datasheet for additional features

Isolated Synchronous Flyback Controller with Integrated iCoupler Features: Current mode controller for flyback topology ADP1071-1: programmable LLM or CCM for high VIN applications ADP1071-2: forced CCM operation Programmable slope compensation Integrated 5 kV isolation (wide body SOIC package) or 3.0 kV (LGA package) rated dielectric isolation voltage with Analog Devices, Inc., patented iCoupler technology Wide voltage supply range Primary VDD: up to 60 V (ADP1071-2 only) Secondary VDD2: up to 36 V Integrated 1 A primary side MOSFET driver Integrated 1 A secondary side MOSFET drivers for synchronous rectification Integrated error amplifier and <1% accurate reference voltage Programmable frequency range: 50 kHz to 600 kHz Duty cycle clamp limit 85% Programmable soft start and soft start from precharged load Protection features such as short circuit, output overvoltage, and overtemperature protection Power saving LLM using MODE pin (ADP1071-1only) Cycle by cycle input overcurrent protection Precision enable UVLO with hysteresis Frequency synchronization Safety and regulatory approvals (pending) UL recognition 5000 V rms for 1 minute per UL 1577 (for wide body SOIC package) 3000 V rms for 1 minute per UL 1577 (for LGA package) CSA Component Acceptance Notice 5A VDE certificate of conformity DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 VIORM = 849 V peak (for wide body SOIC package) VIORM = 565 V peak (for LGA package) CQC certification per GB4943.1-2011 Available in 16-lead SOIC_W package and 24 terminal LGA package