The ADuM4470 / ADuM4471 / ADuM4472 / ADuM4473 / ADuM4474 are quad-channel, digital isolations with a regulated DC/DC isolated power supply controller with an internal MOSFET driver. The DC/DC controller has an internal isolated PWM feedback from the secondary side based on the iCoupler® chip scale transformer technology and complete loop compensation. This eliminates the need to use an optocoupler for feedback and compensates the loop for stability.The ADuM447x isolator provides a more stable output voltage and higher efficiency compared to unregulated isolated DC/DC jpower supplies. The fully integrated feedback and loop compensation in a wide-body SOIC package provide a smaller form factor and 8.3 mm creepage distance solution. The regulated feedback provides a relatively flat efficiency curve over the full output power range. The ADuM3070 enables a DC/DC converter with a 3.3 V to 24 V isolated output voltage range from either a 5.0 V or a 3.3 V input voltage, with an output power of up to 2.5 W.The ADuM447x isolators provide four independent isolation channels in a variety of channel configurations and data rates. (The x in ADuM447x throughout this data sheet stands for the ADuM4470 / ADuM4471 / ADuM4472 / ADuM4473 / ADuM4474).APPLICATIONS Power supply startup bias and gate drives Isolated sensor interfaces Process controls RS-232/RS-422/RS-485 transceivers

The ADuM6210 / ADuM6211 / ADuM6212 are dual-channel digital isolators with isoPower®, an integrated, isolated dc-to-dc converter. Based on the Analog Devices, Inc., iCoupler® technology, the dc-to-dc converter provides regulated, isolated power that is adjustable between 3.135 V and 5.25 V. Input supply voltages can range from slightly below the required output to significantly higher. Popular voltage combinations and their associated power levels are shown in Table 2.The ADuM6210 / ADuM6211 / ADuM6212 eliminate the need for a separate, isolated dc-to-dc converter in low power, isolated designs. The iCoupler chip-scale transformer technology is used for isolated logic signals and for the magnetic components of the dc-to-dc converter. The result is a small form factor, total isolationsolution.isoPower uses high frequency switching elements to transfer power through its transformer. Take special care during printed circuit board (PCB) layout to meet emissions standards. See theAN-0971 Application Note for board layout recommendations.APPLICATIONS RS-232 transceivers Power supply start-up bias and gate drives Isolated sensor interfaces Industrial PLCs

Digital Potentiometer ICs 256tap, Dual DigiPOT, NVM, I2C

SigmaDSP Compact Digital Audio Processor with Extended Internal Memory Features: Qualified for automotive applications High performance SigmaDSP core enables low latency and audio applications Active Noise Cancellation (ANC) Echo-Canceller and Noise Reduction (ECNR) Surround sound algorithms Features SigmaStudio, a proprietary graphical Integrated Development Environment (IDE), for the development of custom signal flows Comprehensive Toolbox of pre-defined building blocks Faster design time with proven solutions Intuitive system design 294.912 MHz, 32-bit SigmaDSP core at 1.2 V 24 kWords of program memory 80 kWords of parameter/data RAM 6144 SIMD instructions per sample at 48 kHz 1600 ms digital audio delay pool at 48 kHz Audio I/O and routing 4 serial input ports, 4 serial output ports 48-channel, 32-bit digital I/O up to a sample rate of 192 kHz Flexible configuration of I2S, left and right justified, and up to 16-channel TDM formats on serial data pins 8 stereo ASRCs from 1:8 up to 7.75:1 ratio and 139 dB dynamic range Stereo S/PDIF input and output at 192 kHz Four PDM microphone input channels Multichannel, byte addressable TDM serial ports Clock oscillator for generating master clock from crystal Integer PLL and flexible clock generators Integrated die temperature sensor I2C and SPI control interfaces (both slave and master) Standalone operation Self-boot from serial EEPROM 6-channel, 10-bit SAR auxiliary control ADC 14 multipurpose pins for digital controls and outputs On-chip regulator for generating 1.2 V from 1.8 V to 3.3 V supply 72-lead, 10 mm × 10 mm LFCSP package with 5.3 mm exposed pad Temperature range: −40°C to +105°C

The AD8188 (G = 1) is a high speed, single-supply, triple 2-to-1 multiplexer. It offers -3 dB small signal bandwidth of 350 MHz and -3 dB large signal bandwidth of 300 MHz, along with a slew rate in excess of 1000 V/µs. With -84 dB of all hostile crosstalk and -95 dB off isolation, the part is well suited for many high speed applications. The differential gain and differential phase error of 0.05% and 0.05° respectively, along with 0.1 dB flatness to 70 MHz, make the AD8188 ideal for professional and component video multiplexing. The part offers 4 ns switching time, making them an excellent choice for switching video signals, while consuming less than 20 mA on a single 5 V supply (100 mW). The device has a high speed disable feature that sets the outputs into a high impedance state. This allows the building of larger input arrays while minimizing off-channel output loading. The device is offered in a 24-lead TSSOP.

The ADF5902 is a 24 GHz transmitter (Tx) monolithic microwaveintegrated circuit (MMIC) with an on-chip, 24 GHz voltagecontrolled oscillator (VCO). The VCO features a fractional-Nfrequency synthesizer with waveform generation capability withprogrammable grid array (PGA) and dual transmitter channelsfor radar systems. The on-chip, 24 GHz VCO generates the24 GHz signal for the two transmitter channels and the localoscillator (LO) output. Each transmitter channel contains apower control circuit. There is also an on-chip temperaturesensor.Control of all the on-chip registers is through a simple, 4-wireserial peripheral interface (SPI).The ADF5902 comes in a compact, 32-lead, 5 mm ? 5 mmLFCSP package. Applications Automotive radars Industrial radars Microwave radar sensors

Dual 10GHz GBW, 1.1nV/Hz Differential Amplifier/ADC Driver Features: 10GHz Gain-Bandwidth Product 85dB SFDR at 100MHz, 2VP-P 1.1nV/√Hz Input Noise Density Channel Separation 95dB at 100MHz Input Range Includes Ground External Resistors Set Gain (Min 1V/V) 3300V/μs Differential Slew Rate 52mA Supply Current (Per Amplifier) 2.7V to 5.25V Supply Voltage Range Fully Differential Input and Output Adjustable Output Common Mode Voltage Low Power Shutdown Small 20-Lead 4mm × 3mm × 0.75mm LQFN Package

Ultralow Voltage Step-Up Converter and Power Manager Features: Operates from Inputs of 20mV Complete Energy Harvesting Power Management System Selectable VOUT of 2.5V, 3V, 3.7V or 4.5V LDO: 2.2V at 3mA Logic Controlled Output Reserve Energy Output Power Good Indicator Uses Compact Step-Up Transformers Small 12-Lead (3mm × 4mm) DFN or 16-Lead SSOP Packages

The LTM4623 is a complete 3A step-down switchingmode ?Module (micromodule) regulator in a tiny ultrathin6.25mm ? 6.25mm ? 1.82mm LGA and 6.25mm ? 6.25mm? 2.42mm BGA packages. Included in the package are theswitching controller, power FETs, inductor and supportcomponents. Operating over an input voltage range of4V to 20V or 2.375V to 20V with an external bias supply,the LTM4623 supports an output voltage range of 0.6V to5.5V, set by a single external resistor. Its high efficiencydesign delivers 3A continuous output current. Only ceramicinput and output capacitors are needed.The LTM4623 supports selectable discontinuous modeoperation and output voltage tracking for supply rail sequencing.Its high switching frequency and current modecontrol enable a very fast transient response to line andload changes without sacrificing stability. Fault protection features include overvoltage, overcurrentand overtemperature protection.The LTM4623 is available with SnPb (BGA) or RoHScompliant terminal finish.APPLICATIONS PCIe and Backside PCB Mounting Telecom, Datacom, Networking and Industrial Equipment Data Storage Rack Units and Cards

The ADT7301 is a complete temperature monitoring system in SOT-23 and MSOP packages. It contains a band gap temperature sensor and a 13-bit ADC to monitor and digitize the temperature reading to a resolution of 0.03125°C.The ADT7301 has a flexible serial interface that allows easy interfacing to most microcontrollers. The interface is compatible with SPI™, QSPI and MICROWIRE™ protocol and is also compatible with DSPs. The part features a standby mode that is controlled via the serial interface. The ADT7301's wide supply voltage range, low supply current and SPI-compatible interface, make it ideal for a variety of applications, including personal computers, office equipment, automotive and domestic appliances. TheADT7301 is rated for operation over the −40°C to +150°Ctemperature range. It is not recommended to operate the deviceat temperatures above +125°C for greater than a total of 5% (5,000 hours) of the lifetime of the device. Exposure beyond thislimit affects device reliability.PRODUCT HIGHLIGHTS On-chip temperature sensor that allows an accurate measurement of the ambient temperature. The measurable temperature range is −40°C to +150°C. Supply voltage of 2.7 V to 5.25 V. Space-saving 6-lead SOT-23 and 8-lead MSOP packages. Typical temperature accuracy of ±0.5°C. 13-bit temperature reading to 0.03125°C resolution. Shutdown mode that reduces the power consumption to 4.88 μW with VDD = 3.3 V @ 1 SPS. Compatible with AD7814.APPLICATIONS Medical equipment Automotive Environmental controls Oil Temperature Hydraulic systems Cellular phones Hard disk drives Personal computers Electronic test equipment Office equipment Domestic appliances Process control