Dual 1MSPS, 12-Bit, 2-Channel SAR ADC with Serial Interface Features: Dual 12-Bit, 2-Channel ADC Fast Throughput Rate 1 MSPS Specified for VDD of 2.7 V to 5.25 V Low Power: 11.4 mW Max at 1 MSPS with 3 V Supplies 24 mW Max at 1 MSPS with 5 V Supplies Wide Input Bandwidth 70 dB SNR at 300 kHz Input Frequency Onboard Reference 2.5 V Flexible Power/Throughput Rate Management Simultaneous Conversion/Read No Pipeline Delays High-Speed Serial Interface SPI®/QSPI™/ MICROWIRE™/DSP Compatible Shut-Down Mode: µA Max 20-Lead TSSOP Package

Precision Analog Microcontroller with Chemical Sensor Interface Features: Analog input/output 16-bit, 400 kSPS ADC Voltage, current, and impedance measurement capability Internal and external current and voltage channels Ultralow leakage switch matrix and input mux Input buffers, PGA Voltage DACs Two dual output voltage DACs Output range: 0.2 V to 2.4 V (±2.2 V voltage potential to sensor) for 12-bit outputs Two bias potentiostat and TIA amplifiers   Ultralow power, 1 μA per amplifier One high speed 12-bit voltage DAC Output range to sensor: −607 mV to +607 mV High speed TIA for impedance measurements Programmable gain amplifier on output Amplifiers, accelerators, and references Two low power, low noise amplifiers Suitable for potentiostat bias in electrochemical sensing Two low power, low noise TIAs Suitable for measuring sensor current output in the ±0.00005 μA to ±3000 μA range Programmable load and gain resistors Analog hardware accelerators Digital waveform generator DFT and digital filters 2.5 V and 1.82 V on-chip, precision voltage references Internal Temperature Sensor, ±2°C accurate Impedance measurement range of <1 Ω to 10 MΩ, 0.016 Hz to 200,000 Hz Voltammetry scan rate up to 2000 steps per second Microcontroller 26 MHz ARM Cortex-M3 processor Serial wire port supports code download and debugging 128 kB flash/64 kB of SRAM Security and safety Hardware cyclic redundancy check (CRC) with programmable polynomial generator Read and write protection of user flash On-chip peripherals UART, I2C, and SPI serial input/output Up to 17 GPIO pins External interrupt option General-purpose, wake-up, and watchdog timers Power 2.8 V to 3.6 V supply and active measurement range Power supply monitor Active current consumption: 30 μA/MHz for digital section Hibernate with bias to external sensor: 8.5 μA Shutdown mode with no SRAM retention: 2 μA Package and temperature range 6 mm × 5 mm, 72-lead LGA package Fully specified for −40°C to +85°C ambient operation

Precision Analog Microcontroller, 16-Bit Analog Input/Output with MDIO Interface, Arm Cortex-M33 Features: Analog input/output Multichannel, 16-bit, 2 MSPS ADC Up to 16 external channels On-chip die temperature monitor 4 power monitor channels 4 PGA/TIA channels supporting voltage and current measurements Fully differential and single-ended modes 0 V to VREF analog input range 12-bit voltage output DACs 8× 0 V to 2.5 V, 1 kΩ load 4× 0 V to 2.5 V, 2.5 kΩ load On-chip low drift voltage reference, 1.25 V or 2.5 V Buffered 1.25 V or 2.5 V output 4 voltage comparators Microcontroller 32-bit Arm Cortex-M33 core, 32-bit RISC architecture, FPU Serial wire port supports code download and debug Clocking options 16 MHz on-chip oscillator 160 MHz PLL output with programmable divider External clock source Memory 2× 512 kB independent Flash/EE memories 10,000-cycle Flash/EE endurance 20-year Flash/EE retention 128 kB SRAM with ECC Software triggered, in circuit reprogrammability via MDIO or I2C On-chip peripherals 2× UART, 3× SPI, 3× I2C serial input/output Multilevel voltage (3.3 V, 1.8 V, 1.2 V) GPIOs MDIO slave up to 10 MHz 5 general-purpose timers Wake-up timer (WUTs) Watchdog timers (WDTs) 32-element PLA 16-bit PWM 10 external Interrupts Power Multiple supplies: 3.3 V for voltage DACs and ADCs, and 3.3 V, 1.8 V, or 1.2 V for digital inputs/outputs Flexible operating modes for low power applications Packages and temperature range 5 mm × 5 mm 81-ball CSP_BGA and 3.46 mm × 3.46 mm 64-ball WLCSP BGA package uses ULA molding compounds Fully specified for −40°C to +105°C operation Tools Low cost quick start development system Full third-party support  

Precision Analog Microcontroller, 12-Bit Analog Input and Output with PMIC and TECC, Arm Cortex-M3 Features: Analog input and output Multichannel, 12-bit, 2 MSPS ADC Up to 16 external channels Power, VDAC, IDAC, and temperature monitor internal channels Single-ended and differential mode 0 V to VREF analog input range Input buffer included Digital comparators Up to nine, 12-bit voltage output VDACs 4-channel, selectable output range 0 V to 2.5 V or AVDDx − 0.1 V AVDDNEG + 0.2 V to 0 V or −2.5 V to 0 V 4-channel, 0 V to 2.5 V or AVDDx − 0.2 V 1-channel, 0 V to 2.5 V Up to 4 low noise, 12-bit IDACs Configurable output range: 50 mA, 100 mA, or 150 mA 4 voltage comparators with adjustable hysteresis voltage TEC controller Optional LDO regulator modes if not using TEC Maximum heating and cooling current: 1.3 A Current and voltage monitoring and protection Soft start function Microcontroller 32-bit Arm Cortex-M3 core, RISC architecture Serial wire port supports code download and debug Clocking options 16 MHz on-chip oscillator 80 MHz PLL output External clock source Memory 2× 512 kB independent Flash/EE memories 48 kB SRAM Software triggered, in circuit reprogrammability via I2C On-chip peripherals 1× UART, 2× SPI, 2× I2C serial input and output GPIO with multilevel voltage (3.3 V, 1.8 V, and 1.2 V) digital inputs MDIO target up to 4 MHz (open drain) 3× 16-bit and 1× 32-bit general-purpose timers Wake-up timer (WUT) Watchdog timers (WDT) 32 element PLA 16-bit PWM Manchester encoder and decoder All GPIOs support external interrupt Power Multiple supplies AVDDx, IOVDD, DVDD, and PVDDTECx: 2.85 V to 3.63 V AVDDNEG: −1.8 V to −3.63 V PVDDIDACx: 1.60 V to AVDDx Flexible operating modes for low power applications Packages and temperature range 5 mm x 5 mm, 0.4 mm pitch, 121-ball CSP_BGA Fully specified for TJ = –40°C to +125°C Tools Low cost QuickStart development system, which is available upon request from InfoOpticalNetwork@analog.com Full third-party support

3.75 kV RMS Digital Isolators for Isolated USB 2.0 High, Full, and Low Speed Features: USB 2.0 signaling with automatic detection of low, full, and high speed connections 1.5 Mbps, 12 Mbps, and 480 Mbps data rates Bidirectional USB isolator for upstream and downstream ports Redriving and high speed data retiming for input jitter removal and an open eye Flexible clock input options 4.5 V to 5.5 V VBUSx or 3 V to 3.6V operation on each side 21 mA typical idle, low or full speed mode supply current 48 mA typical idle, high speed mode supply current Ultra low power standby in USB 2.0 suspend (L2) or disconnect 1.7 mA typical low power standby, upstream supply current 20 μA typical low power standby, downstream supply current ±6000 V IEC 61000-4-2 ESD protection across the isolation barrier Passed CISPR32/EN55032 Class B emissions High common-mode transient immunity: 50 kV/μs typical Safety and regulatory approvals (pending) UL (pending): 3750 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A (pending) IEC 62368-1, IEC 61010-1, and IEC60601-1 VDE certificate of conformity (pending) DIN V VDE V 0884-11 (VDE V 0884-11):2017-01 VIORM = 849 VPEAK (working voltage) Operating temperature range: −55°C to +125°C Compact 20-lead SSOP with 5.3 mm creepage and clearance

5.7kV rms Digital Isolator for Isolated USB 2.0 High Speed (Upstream Clock Input) Features: USB 2.0 signaling with automatic detection of low, full, and high speed connections 1.5 Mbps, 12 Mbps, and 480 Mbps data rates Bidirectional USB isolator for upstream or downstream ports Redriving and high speed data retiming for input jitter removal and an open eye Flexible clock input options 4.5 V to 5.5 V VBUSx or 3 V to 3.6 V operation on each side 21 mA typical idle, low or full speed mode supply current 48 mA typical idle, high speed mode supply current Ultra low power standby in USB 2.0 suspend (L2) or disconnect 1.7 mA typical low power standby, upstream supply current 20 μA typical low power standby, downstream supply current ±8000 V IEC 61000-4-2 ESD protection across the isolation barrier Passed CISPR32/EN55032 Class B emissions High common-mode transient immunity: 50 kV/μs typical Safety and regulatory approvals (pending) UL (pending): 5700 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A (pending) IEC 62368-1, IEC 61010-1 and IEC60601‑1 VDE certificate of conformity (pending) DIN V VDE V 0884-11 (VDE V 0884-11):2017-01 VIORM = 849 VPEAK Operating temperature range: −55°C to +125°C 20-lead, wide-body, increased creepage SOIC_IC package with 8.3 mm creepage and clearance

Low Emission 500 mW Isolated DC-to-DC Converter Features: isoPower integrated, isolated dc-to-dc converter 100 mA output current for ADuM5020 60 mA output current for ADuM5028 Meets CISPR22 Class B emissions limits at full load on a 2-layer PCB 16-lead SOIC_W package with 7.8 mm minimum creepage 8-lead SOIC_IC package with 8.3 mm minimum creepage High temperature operation: 125°C maximum Safety and regulatory approvals UL recognition (pending) 3000 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A (pending) VDE certificate of conformity (pending) VDE V 0884-10 VIORM = 565 V peak CQC certification per GB4943.1-2011 (pending) 

10-Bit, 4 Oversampled SDTV Video Decoder with Deinterlacer Features: Worldwide NTSC/PAL/SECAM color demodulation support One 10-bit ADC, 4× oversampling per channel for CVBS, Y/C, and YPrPb modes Analog video input channels with on-chip antialiasing filter ADV7280A: up to 4 input channels ADV7280A-M: up to 8 input channels Video input support for CVBS (composite), S-Video (Y/C), and YPrPb (component) NTSC/PAL/SECAM autodetection Up to 1.47 V common-mode input range solution Excellent common-mode noise rejection capabilities 5-line adaptive 2D comb filter and CTI video enhancement Integrated AGC with adaptive peak white mode Fast switching capability Integrated I2P video output converter (deinterlacer) ACE Downdither (8-bit to 6-bit) Rovi copy protection detection MIPI CSI-2 output interface (ADV7280A-M) 8-bit ITU-R BT.656 YCrCb 4:2:2 output and HS, VS, or field synchronization (ADV7280A) Full featured VBI data slicer with WST support Power-down mode available 2-wire, I2C-compatible serial interface Qualified for automotive applications −40°C to +105°C temperature grade 32-lead, 5 mm × 5 mm, RoHS compliant LFCSP

10-Bit, 4 Oversampled SDTV Video Decoder with Differential Inputs and Deinterlacer Features: Worldwide NTSC/PAL/SECAM color demodulation support One 10-bit analog-to-digital converter (ADC), 4× oversampling per channel for CVBS, Y/C, and YPrPb modes ADV7282: 4 analog video input channels with on-chip antialiasing filter ADV7282-M: 6 analog video input channels with on-chip antialiasing filter Video input support for CVBS (composite), Y/C (S-Video), and YPrPb (component) Fully differential, pseudo differential, and single-ended CVBS video input support NTSC/PAL/SECAM autodetection Up to 4 V common-mode input range solution Excellent common-mode noise rejection capabilities 5-line adaptive 2D comb filter and CTI/DNR video enhancement Adaptive Digital Line Length Tracking (ADLLT), signal processing, and enhanced FIFO management provide mini-time base correction (TBC) functionality See data sheet for additional features

3-Axis, 0.5 g/1 g/2 g/4 g Digital Accelerometer Features: Ultralow power (scales automatically with data rate) As low as 30 μA in measurement mode (VS = 3.3 V) As low as 0.1 μA in standby mode (VS = 3.3 V) Low noise performance 150 μg/√Hz typical for X- and Y-axes 250 μg/√Hz typical for the Z-axis Embedded, patent pending FIFO technology minimizes host processor load User-selectable resolution Fixed 10-bit resolution for any g range Fixed 1024 LSB/g sensitivity for any g range Resolution scales from 10-bit at ±0.5 g to 13-bit at ±4 g Built-in motion detection functions for activity/inactivity monitoring Supply and I/O voltage range: 2.0 V to 3.6 V See data sheet for additional features