Integrated Dual RF Receiver Features: Dual receivers Maximum Receiver BW: 200 MHz Fully integrated, fractional-N, RF synthesizers Fully integrated clock synthesizer Multichip phase synchronization for RF LO and baseband clocks JESD204B datapath interface Tuneable range: 75 MHz to 6000 MHz

High Performance Fourth Generation DSP Features: 200 MHz core clock speed 2 Mbits of on-chip RAM FIR, IIR, and FFT accelerators Digital Applications Interface (DAI) enabling user-definable access to peripherals including an S/P DIF Tx/Rx, and 8-channel asynchronous sample rate converter Fully enhanced DMA engine including scatter/gather DMA, delay line DMA 8 serial ports (SPORTs) supporting I2S, left-justified sample pair, and TDM modes Watch Dog Timer Shift Registers 2 SPI-compatible ports supporting master and slave modes UART and Two-Wire Interface 16 Pulse Width Modulation (PWM) channels 3 full-featured timers Small footprint, 88-lead LFCSP and 100-Ld LQFP package options Commercial, Industrial, and automotive temperature ranges available

Up to 1GHz SHARC+ DSP with 640KB L1, 1024KB Shared L2 SRAM, 400-Ball CSP_BGA Features:SHARC+ Core infrastructure 800MHz (max) or 1GHz (max) Core clock frequency 640KB on-chip Level 1 (L1) SRAM memory (with parity) increases low latency performance 32-bit, 40-bit & 64-bit floating point support 32-bit fixed point Byte, short-word, word, long-word addressedMemory 1024KB on-chip Level 2 (L2) SRAM with ECC protection - eliminates need for external memory in many use cases One Level 3 (L3) interface optimized for low system power, providing 16-bit interface to DDR3 (supporting 1.35 V capable DDR3L devices) SDRAM devices16-bit DDR/DDR3L Memory Controller 1.35V support for DDR3LAdvanced Hardware Accelerators Enhanced FIR/IIR offload engines running at Core clock frequency for added processing power Security Crypto Engines with OTPPowerful DMA SystemInnovative Digital Audio Interface (DAI) includes: 8x Full SPORT interfaces w/TDM & I2S modes 2x S/PDIF Rx/Tx, 8 ASRC pairs 4x Precision Clock Generators 28 BuffersOther Peripheral Connectivity / Interfaces: 2x Quad SPI, 1x Octal SPI MLB 3-pin 6x I2C,3x UARTs 2x Link Ports 10x General Purpose Timer, 1x General Purpose Counter 2x Watchdog Timers 4-ch 12bit Housekeeping ADCs 40 GPIO pins, 28 DAI pins Thermal SensorPackage 17mm x 17mm (0.8mm pitch) 400-ball CSP_BGAAdditional Features Security and Protection Crypto hardware accelerators Fast secure boot with IP protection Enhanced FIR and IIR accelerators running up to 1 GHz AEC-Q100 qualified for automotive applications

Robust, Quad Channel Isolator W/ Input Disable & 0 Reverse Channels Features: High common-mode transient immunity: 100 kV/μs High robustness to radiated and conducted noise Low propagation delay 13 ns maximum for 5 V operation 15 ns maximum for 1.8 V operation 150 Mbps maximum guaranteed data rate Safety and regulatory approvals UL recognition 3000 V rms/3750 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A VDE certificate of conformity DIN V VDE V 0884-11 (VDE V 0884-11):2017-01 VIORM = 849 V peak CQC certification per GB4943.1-2011 Backward compatibility ADuM140E1/ADuM141E1/ADuM142E1 pin-compatible with ADuM1400/ADuM1401/ADuM1402 Low dynamic power consumption 1.8 V to 5 V level translation High temperature operation: 125°C Fail-safe high or low options 16-lead, RoHS compliant, SOIC package Qualified for automotive applications

Dual-mode, Ka Band Upconverter withIntegrated Fractional-N PLL and VCO Features: RF output frequency range: 27 GHz to 31 GHz Two upconversion modes Direct upconversion from differential baseband I/Q (I/Q mode) Single upper sideband upconversion (IF mode) 1 dB bandwidth: 500 MHz (I/Q mode) Input frequency range: 2 GHz to 3 GHz (IF mode) Matched, 50 Ω, single-ended RF output Matched, 50 Ω, single-ended IF input Programmable baseband I/Q common mode-voltage Sideband rejection and carrier feedthrough optimization Combined RF and IF gain dynamic range: 70 dB Programmable automatic IF gain control Programmable via 3-wire or 4-wire SPI 40-terminal, 6 mm × 6 mm, RoHS compliant LGA

Ultracompact 1.5 A Thermoelectric Cooler (TEC) Controller Features: Patented high efficiency single inductor architecture Integrated low RDSON MOSFETs for the TEC controller TEC voltage and current operation monitoring No external sense resistor required Independent TEC heating and cooling current limits settings Programmable maximum TEC voltage 2.0 MHz PWM driver switching frequency External synchronization Two integrated zero drift, rail-to-rail chopper amplifiers Capable of NTC or RTD thermal sensors 2.50 V reference output with 1% accuracy Temperature lock indicator Available in a 25-ball, 2.5 mm × 2.5 mm WLCSP or in a 24-lead, 4 mm × 4 mm LFCSP AEC-Q100 qualified for automotive applications

Three-Channel, Isolated Micropower Management Unit with Seven Digital Isolators Features: Wide input supply voltage range: 4.5 V to 60 V Integrated flyback power switch Generates isolated, independent bipolar outputs and factory programmable buck output VOUT1: 21 V, 24 V or 6 V to 28 V VOUT2: 5.15 V, 5.0 V, or 3.3 V VOUT3: −24 V to −5 V Uses a 1:1 ratio transformer for simplified transformer design Peak current limiting and OVP for flyback, buck, and inverting regulators Precision enable input and power-good output Adjustable switching frequency via SYNC input Internal compensation and soft start control per regulator High speed, low propagation delay, SPI signal isolation channels Three, 100 kbps general-purpose isolated data channels 9 mm × 7 mm LFCSP form factor enables small overall solution size −40°C to +125°C operating junction temperature range Conforms to CISPR11 Class B radiated emission limits Safety and regulatory approvals (pending) UL recognition: 2500 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A 300 V rms basic insulation between slave, master, and field power domains (IEC 61010-1, pending) VDE certificate of conformity DIN V VDE 0884-10 (VDE 0884-10):2006-12 VIORM = 565 VPEAK

Three-Channel, Isolated Micropower Management Unit with Seven Digital Isolators Features: Wide input supply voltage range: 4.5 V to 60 V Integrated flyback power switch Generates isolated, independent bipolar outputs and factory programmable buck output VOUT1: 21 V, 24 V or 6 V to 28 V VOUT2: 5.15 V, 5.0 V, or 3.3 V VOUT3: −24 V to −5 V Uses a 1:1 ratio transformer for simplified transformer design Peak current limiting and OVP for flyback, buck, and inverting regulators Precision enable input and power-good output Adjustable switching frequency via SYNC input Internal compensation and soft start control per regulator High speed, low propagation delay, SPI signal isolation channels Three, 100 kbps general-purpose isolated data channels 9 mm × 7 mm LFCSP form factor enables small overall solution size −40°C to +125°C operating junction temperature range Conforms to CISPR11 Class B radiated emission limits Safety and regulatory approvals (pending) UL recognition: 2500 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A 300 V rms basic insulation between slave, master, and field power domains (IEC 61010-1, pending) VDE certificate of conformity DIN V VDE 0884-10 (VDE 0884-10):2006-12 VIORM = 565 VPEAK

Two-Channel, Isolated Micropower Management Unit with Seven Digital Isolators Features: Wide input supply voltage range: 4.5 V to 60 V Integrated flyback power switch Generates two isolated, well regulated independent outputs VOUT1: 24 V or 6 V to 28 V VOUT2: 3.3 V, 5.0 V, or 5.15 V Uses a 1:1 ratio transformer for simplified transformer design Peak current limiting and OVP for flyback and buck regulators Precision enable input and power-good output Adjustable switching frequency via SYNC input Internal compensation and soft start control per regulator High speed, low propagation delay, SPI signal isolation channels Three 100 kbps general-purpose isolated data channels 41-lead, 9 mm × 7 mm LFCSP form factor enables small overall solution size −40°C to +125°C operating junction temperature range Safety and regulatory approvals (pending) CISPR11 Class B radiated emission UL recognition: 2500 V rms for 1 minute duration per UL 1577 CSA Component Acceptance Notice 5A 300 V rms basic insulation between slave, master, and field power domains (IEC 61010-1, pending) VDE certificate of conformity DIN V VDE 0884-10 (VDE 0884-10):2006-12 VIORM = 565 VPEAK

Digital Controller for Isolated Power Supply Applications Features: Integrates all typical PWM controller functions 7 PWM control signals Digital control loop Integrated programmable loop filters Programmable voltage line feedforward Dedicated soft start filter Remote and local voltage sense Primary and secondary side current sense Synchronous rectifier control Current sharing OrFET control I2C interface Extensive fault detection and protection Extensive programming and telemetry Fast digital calibration User accessible EEPROM Qualified for automotive applications Download ADP1046AW Automotive Data Sheet (pdf)