Ultracompact 1.5 A Thermoelectric Cooler (TEC) Controller Features: Patented high efficiency single inductor architecture Integrated low RDSON MOSFETs for the TEC controller TEC voltage and current operation monitoring No external sense resistor required Independent TEC heating and cooling current limits settings Programmable maximum TEC voltage 2.0 MHz PWM driver switching frequency External synchronization Two integrated zero drift, rail-to-rail chopper amplifiers Capable of NTC or RTD thermal sensors 2.50 V reference output with 1% accuracy Temperature lock indicator Available in a 25-ball, 2.5 mm × 2.5 mm WLCSP or in a 24-lead, 4 mm × 4 mm LFCSP AEC-Q100 qualified for automotive applications

Three-Channel, Isolated Micropower Management Unit with Seven Digital Isolators Features: Wide input supply voltage range: 4.5 V to 60 V Integrated flyback power switch Generates isolated, independent bipolar outputs and factory programmable buck output VOUT1: 21 V, 24 V or 6 V to 28 V VOUT2: 5.15 V, 5.0 V, or 3.3 V VOUT3: −24 V to −5 V Uses a 1:1 ratio transformer for simplified transformer design Peak current limiting and OVP for flyback, buck, and inverting regulators Precision enable input and power-good output Adjustable switching frequency via SYNC input Internal compensation and soft start control per regulator High speed, low propagation delay, SPI signal isolation channels Three, 100 kbps general-purpose isolated data channels 9 mm × 7 mm LFCSP form factor enables small overall solution size −40°C to +125°C operating junction temperature range Conforms to CISPR11 Class B radiated emission limits Safety and regulatory approvals (pending) UL recognition: 2500 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A 300 V rms basic insulation between slave, master, and field power domains (IEC 61010-1, pending) VDE certificate of conformity DIN V VDE 0884-10 (VDE 0884-10):2006-12 VIORM = 565 VPEAK

Three-Channel, Isolated Micropower Management Unit with Seven Digital Isolators Features: Wide input supply voltage range: 4.5 V to 60 V Integrated flyback power switch Generates isolated, independent bipolar outputs and factory programmable buck output VOUT1: 21 V, 24 V or 6 V to 28 V VOUT2: 5.15 V, 5.0 V, or 3.3 V VOUT3: −24 V to −5 V Uses a 1:1 ratio transformer for simplified transformer design Peak current limiting and OVP for flyback, buck, and inverting regulators Precision enable input and power-good output Adjustable switching frequency via SYNC input Internal compensation and soft start control per regulator High speed, low propagation delay, SPI signal isolation channels Three, 100 kbps general-purpose isolated data channels 9 mm × 7 mm LFCSP form factor enables small overall solution size −40°C to +125°C operating junction temperature range Conforms to CISPR11 Class B radiated emission limits Safety and regulatory approvals (pending) UL recognition: 2500 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A 300 V rms basic insulation between slave, master, and field power domains (IEC 61010-1, pending) VDE certificate of conformity DIN V VDE 0884-10 (VDE 0884-10):2006-12 VIORM = 565 VPEAK

Two-Channel, Isolated Micropower Management Unit with Seven Digital Isolators Features: Wide input supply voltage range: 4.5 V to 60 V Integrated flyback power switch Generates two isolated, well regulated independent outputs VOUT1: 24 V or 6 V to 28 V VOUT2: 3.3 V, 5.0 V, or 5.15 V Uses a 1:1 ratio transformer for simplified transformer design Peak current limiting and OVP for flyback and buck regulators Precision enable input and power-good output Adjustable switching frequency via SYNC input Internal compensation and soft start control per regulator High speed, low propagation delay, SPI signal isolation channels Three 100 kbps general-purpose isolated data channels 41-lead, 9 mm × 7 mm LFCSP form factor enables small overall solution size −40°C to +125°C operating junction temperature range Safety and regulatory approvals (pending) CISPR11 Class B radiated emission UL recognition: 2500 V rms for 1 minute duration per UL 1577 CSA Component Acceptance Notice 5A 300 V rms basic insulation between slave, master, and field power domains (IEC 61010-1, pending) VDE certificate of conformity DIN V VDE 0884-10 (VDE 0884-10):2006-12 VIORM = 565 VPEAK

Digital Controller for Isolated Power Supply Applications Features: Integrates all typical PWM controller functions 7 PWM control signals Digital control loop Integrated programmable loop filters Programmable voltage line feedforward Dedicated soft start filter Remote and local voltage sense Primary and secondary side current sense Synchronous rectifier control Current sharing OrFET control I2C interface Extensive fault detection and protection Extensive programming and telemetry Fast digital calibration User accessible EEPROM Qualified for automotive applications Download ADP1046AW Automotive Data Sheet (pdf)

Isolated, Synchronous Forward Controller with Active Clamp and iCoupler Features: Current mode controller for active clamp forward topology Integrated 5 kV (wide body SOIC package) or 3.0 kV (LGA package) rated dielectric isolation voltage with Analog Devices, Inc., patented iCoupler technology Wide voltage supply range Primary VIN: up to 60 V Secondary VDD2: up to 36 V Integrated 1 A primary side MOSFET driver for power switch and active clamp reset switch Integrated 1 A secondary side MOSFET drivers for synchronous rectification Integrated error amplifier and <1% accurate reference voltage Programmable slope compensation Programmable frequency range: 50 kHz to 600 kHz typical Frequency synchronization Programmable maximum duty cycle limit Programmable soft start Smooth soft start from precharged load Programmable dead time Power saving light load mode using MODE pin Protection features such as short circuit, output overvoltage, and overtemperature protection Cycle-by-cycle input overcurrent protection Precision enable UVLO with hysteresis PGOOD pin for system flagging Tracking function from secondary side Remote (secondary side) shutdown/reset function Safety and regulatory approvals (pending) UL recognition 5000 V rms for 1 minute per UL 1577 (for wide body SOIC package) 3000 V rms for 1 minute per UL 1577 (for LGA package) CSA component acceptance notice 5A VDE certificate of conformity DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 VIORM = 849 V peak (for wide body SOIC package) VIORM = 560 V peak (for LGA package) CQC certification per GB4943.1-2011 Available in 24-lead SOIC_W package and 24-terminal LGA package AEC-Q100 Qualified for Automotive Applications

3 A, Low VIN, Low Noise, CMOS Linear Regulator Features: 3 A maximum output current Low input voltage supply range VIN = 1.10 V to 1.98 V, no external bias supply required Fixed output voltage range: VOUT_FIXED = 0.9 V to 1.5 V Adjustable output voltage range: VOUT_ADJ = 0.5 V to 1.5 V Ultralow noise: 2 μV rms, 100 Hz to 100 kHz Noise spectral density 4 nV/√Hz at 10 kHz 3 nV/√Hz at 100 kHz Low dropout voltage: 95 mV typical at 3 A load Operating supply current: 4.5 mA typical at no load ±1.5% fixed output voltage accuracy over line, load, and temperature Excellent power supply rejection ratio (PSRR) performance 59 dB typical at 10 kHz at 3 A load 43 dB typical at 100 kHz at 3 A load Excellent load/line transient response Soft start to reduce inrush current Optimized for small 10 μF ceramic capacitors Current-limit and thermal overload protection Power-good indicator Precision enable 16-lead, 3 mm × 3 mm LFCSP package AEC-Q100 qualified for automotive applications

Quad-Channel Isolators with Integrated DC-to-DC Converter (3:1 directionality) Features: isoPower integrated, isolated dc-to-dc converter 100 mA output supply AEC-Q100 qualified for automotive applications ADuM6421AW (ADuM6423AW pending) Meets CISPR 32/EN55032 Class B emission limits up to 5 Mbps at a full load on a 2-layer PCB Quad dc to 100 Mbps signal isolation channels 28-lead, fine pitch, SOIC with 8.3 mm minimum creepage High temperature operation: 125°C maximum High common-mode transient immunity: 100 kV/μs Safety and regulatory approvals (pending) UL recognition (pending) 5000 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A (pending) VDE V 0884-11 certificate of conformity (pending) VIORM = 566 V peak CQC certification per GB4943.1-2011 (pending)

Isolated Precision Half-Bridge Driver, 4 A Output Features: 4 A peak output current Working voltage: High-side or low-side relative to input: 565 V peak High-side to low-side differential: 700 V peak High frequency operation: 1 MHz maximum Precise timing characteristics: 60 ns maximum isolator and driver Propagation Delay 7 ns maximum channel-to-channel matching 3.3 V to 5 V input Logic 4.5V to 18 V output drive UVLO at 2.5 V VDD1: A Version UVLO at 4.1 V VDD2 CMOS input logic levels High common-mode transient immunity: >25 kV/µs High junction temperature operation: 125°C Default low output 5 × 5 mm, 14-lead LGA

Low Noise, Wide Bandwidth, MEMS Accelerometer Features: Single, in-plane axis accelerometer with analog output Full-scale range: ±200 g Linear frequency response range: dc to 15 kHz typical (3 dB point) Resonant frequency: 28 kHz typical Sensitivity performance Sensitivity stability over temperature within ± 5% Linearity to ±0.2% of full-scale range Cross-axis sensitivity ± 1%/± 0.8% (z-axis acceleration effect on x-axis, y-axis acceleration effect on x-axis) Ultralow noise density 45 μg/√Hz Overrange sensing plus dc coupling allows fast recovery time Complete electromechanical self test Single-supply operation Output voltage ratiometric to supply Low power consumption: 1.0 mA typical Power saving standby operation mode with fast recovery RoHS compliant −40°C to +125°C temperature range 32-lead, 5 mm × 5 mm × 1.8 mm LFCSP package