50 V, 8 MHz, 1.5 mA per Channel, Robust, Over-The-Top, Precision Op Amps Features: Ultrawide common-mode range: −VS − 0.1 V to −VS + 70 V Wide power supply voltage range: (VSY): +3.15 V to +50 V (±25 V for PSRR) Low supply current: 1.5 mA per channel (typical) Low input offset voltage: ±40 μV maximum Low input offset voltage drift: ±0.4 μV/°C maximum Low voltage noise: 1/f noise corner: 6 Hz typical 150 nV p-p typical at 0.1 Hz to 10 Hz 7 nV/√Hz typical at 100 Hz (en) High speed GBP: 8 MHz typical Slew rate: 5.5 V/μs typical at ΔVOUT = 25 V Low power shutdown: 20 μA maximum Low input bias current: ±10 nA maximum Large signal voltage gain: 120 dB minimum CMRR: 118 dB, minimum PSRR: 123 dB, minimum Input overdrive tolerant with no phase reversal ±2 kV HBM and ±1.25 kV FICDM Wide temperature range: −55°C to +150°C (H grade)

SigmaDSP 28-/56-Bit Audio Processor with Two ADCs and Four DACs Features: 28-/56-bit, 50 MIPS digital audio processor 2 ADCs: SNR of 100 dB, THD + N of −83 dB 4 DACs: SNR of 104 dB, THD + N of −90 dB Complete standalone operation Self-boot from serial EEPROM Auxiliary ADC with 4-input mux for analog control GPIOs for digital controls and outputs Fully programmable with SigmaStudio graphical tool 28-bit × 28-bit multiplier with 56-bit accumulator for full double-precision processing Clock oscillator for generating master clock from crystal See Data Sheet for Additional Information

3-Channel Sigma-Delta ADC with SPI Features: One (ADE7903) 24-bit, Σ-Δ ADC (simultaneously sampling with three ADE7912/ADE7913 ADCs) On-chip temperature sensor 4-wire SPI serial interface Standalone 24-bit, Σ-Δ ADC Up to four ADE7903 and ADE7912/ADE7913 devices clocked from a single crystal or an external clock Synchronization of multiple ADE7903 and ADE7912/ADE7913 devices ±31.25 mV peak input range for current channel ±500 mV peak input range for voltage channels Single 3.3 V supply 20-lead, wide body SOIC package Operating temperature: −40°C to +85°C

High Performance FSK/ASK Transceiver IC Features: Low power, low IF transceiver Frequency bands 135 MHz to 650 MHz, direct output 80 MHz to 325 MHz, divide-by-2 mode Data rates supported 0.15 kbps to 200 kbps, FSK 0.15 kbps to 64 kbps, ASK 2.3 V to 3.6 V power supply Programmable output power −20 dBm to +13 dBm in 63 steps Receiver sensitivity −119 dBm at 1 kbps, FSK, 315 MHz −114 dBm at 9.6 kbps, FSK, 315 MHz −111.8 dBm at 9.6 kbps, ASK, 315 MHz Low power consumption 17.6 mA in receive mode 21 mA in transmit mode (10 dBm output) On-chip VCO and fractional-N PLL On-chip 7-bit ADC and temperature sensor Fully automatic frequency control loop (AFC) compensates for lower tolerance crystals Digital RSSI Integrated TRx switch Leakage current <1 µA in power-down mode

Robust, Industrial, Low Latency and Low Power 10 Mbps, 100 Mbps, and 1 Gbps Ethernet PHY Features: 10BASE-Te/100BASE-TX/1000BASE-T IEEE® 802.3™ compliant MII, RMII, and RGMII MAC interfaces 1000BASE-T RGMII latency transmit < 68 ns, receive < 226 ns 100BASE-TX MII latency transmit< 52 ns, receive < 248 ns EMC test standards IEC 61000-4-5 surge (±4 kV) IEC 61000-4-4 electrical fast transient (EFT) (±4 kV) IEC 61000-4-2 ESD (±6 kV contact discharge) IEC 61000-4-6 conducted immunity (10 V) EN55032 radiated emissions (Class A) EN55032 conducted emissions (Class A) Unmanaged configuration using multilevel pin strapping EEE in accordance with IEEE 802.3az Start of packet detection for IEEE 1588 time stamp support Enhanced link detection Configurable LED Crystal oscillator frequency/25 MHz clock input frequency (50 MHz for RMII) 25 MHz/125 MHz synchronous clock output Small package and wide temperature range 40-lead, 6 mm × 6 mm LFCSP Specified for −40°C to +105°C ambient operation Low power consumption 330 mW for 1000BASE-T 140 mW for 100BASE-TX 3.3 V/2.5 V/1.8 V MAC interface VDDIO supply Integrated power supply monitoring and POR

Low Complexity, 2-Port Ethernet Switch with Integrated 10BASE-T1L PHYs Features: 10BASE-T1L IEEE® Std 802.3cg-2019™ compliant Supports 1.0 V p-p & 2.4 V p-p transmit Levels Cable reach Up to 1700 meters with 1.0 V p-p transmit level Up to 1700 meters with 2.4 V p-p transmit level Low power consumption Low power consumption - single supply 80 mW typ Dual supply 1.0 V p-p: 77 mW typical Integrated switch with SPI interface 10 Mbps full duplex 16 MAC addresses supported for frame forwarding Supports OPEN Alliance 10BASE-T1x MACPHY SPI MDIO memory map accessible via SPI Supports high & low priority queues Total buffer memory of 28 kB shared between ports and host Autonegotiation capability Managed or unmanaged configuration Cut through or store and forward operation IEEE 1588 time stamp capture on transmit and receive Diagnostics Frame generator and checker Multiple loopback modes IEEE test mode support Port dedicated statistics counters Link and cable diagnostics 25 MHz crystal or external clock input Single or dual supply with 1.8 V or 3.3 V operation Integrated power supply monitoring and POR Small package: 48-lead, 7 mm × 7 mm LFCSP Temperature range Industrial: 40°C to +85°C Extended: 40°C to +105°C

Hot Swap Controller and Digital Power Monitor with Soft Start Pin Features: Allows safe board insertion and removal from a live backplane  Controls supply voltages from 3.15 V to 16.5 V  Precision current sense amplifier  Precision voltage input  12-bit ADC for current and voltage readback  Charge pumped gate drive for external N-channel FET  Active high ON pin 10-lead MSOP Adjustable analog current limit with circuit breaker  ±3% accurate hot swap current limit level  Fast response limits peak fault current  Automatic retry or latch-off on current fault  Programmable hot swap timing via TIMER pin  Soft start pin for reference adjustment and programming of initial current ramp rate  I2C fast mode-compliant interface (400 kHz maximum)

2.5 kV Signal Isolated, High Speed (16 Mbps), Half Duplex RS-485 Transceiver w/ Transformer Driver Features: Half-duplex, isolated RS-485 transceiver Integrated oscillator driver for external transformer PROFIBUS® compliant Complies with ANSI/TIA/EIA RS-485-A-98 and ISO 8482:1987(E) Data rate: 16 Mbps 5 V or 3.3 V operation (VDD1) High common-mode transient immunity: >25 kV/μs Wide-body, 16-lead SOIC package 50 nodes on bus Isolated DE OUT status output Thermal shutdown protection Safety and regulatory approvals UL recognition: 2500 V rms for 1 minute per UL 1577 VDE Certificate of Conformity DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 Reinforced insulation, VIORM = 560 V peak Operating temperature range: –40°C to +85°CWide-body, 16-lead SOIC package

5.7 kV rms, Signal Isolated, High Working Voltage, CAN FD Transceiver with 15kV IEC ESD Features: 5.7 kV rms signal isolated CAN FD transceiver 1500 V peak and dc working voltage to DIN VDE 0884-11 1.7 V to 5.5 V supply and logic side levels 4.5 V to 5.5 V supply on bus side ISO 11898-2:2016-compliant CAN FD Data rates up to 12 Mbps for CAN FD Low maximum loop propagation delay: 155 ns Extended common-mode range: 25 V Bus fault protection (CANH, CANL): 40 V ESD protection on the CANH and CANL bus pins 8 kV IEC 61000-4-2 contact discharge 15 kV IEC 61000-4-2 air discharge Passes EN 55022, Class B by 6 dB Safety and regulatory approvals (pending) UL: 5700 V rms for 1-minute per UL 1577 CSA Component Acceptance 5A at 5.7 kV rms IEC 60601 and IEC 61010 VDE Certificates of Conformity DIN VDE V 0884-11 (VDE V 0884-11):2017-01 VIORM = 1500 V peak High common-mode transient immunity: >50 kV/s Industrial operating temperature range: 40C to +125C

250 Mbps, Half Duplex, Quad M-LVDS Transceivers Features: Four M-LVDS transceivers (driver and receiver pairs) Switching rate: 250 Mbps (125 MHz) Independent pin select for each receiver, two modes: Type 1: input hysteresis of 15 mV typical Type 2: differential input threshold voltage offset by 100 mV to support open-circuit, short-circuit, and bus idle fail-safe Compatible with the TIA/EIA-899 standard for M-LVDS Glitch free power-up/power-down on the M-LVDS bus Controlled transition times on the driver output Common-mode range: −1 V to +3.4 V, allowing communication with ±2 V of ground noise Driver outputs high-Z when disabled or powered off Independent enable pins for each driver and receiver Enhanced ESD protection on bus pins ≥±15 kV HBM, air discharge ≥±8 kV HBM, contact discharge ≥±10 kV IEC 61000-4-2, air discharge ≥±8 kV IEC 61000-4-2, contact discharge Enhanced ±8 kV HBM ESD protection for all pins, contact discharge Operating temperature range: −40°C to +105°C Available in 48-lead, 7 mm x 7 mm LFCSP