18-Cell Battery Monitor with Daisy Chain Interface Features: Measures up to 18 battery cells in series 3 mV maximum total measurement error Stackable architecture for high voltage systems Built-in isoSPI interface 1 Mb isolated serial communications Uses a single twisted pair, up to 100 meters Low EMI susceptibility and emissions Bidirectional for broken wire protection 290 μs to measure all cells in a system Synchronized voltage and current measurement 16-bit Δ-Σ ADC with programmable third-order noise filter Passive cell balancing up to 200 mA (maximum) with programmable pulsewidth modulation 9 general purpose digital I/O or analog inputs Temperature or other sensor inputs Configurable as an I2C or SPI master 6 μA sleep mode supply current 64-lead LQFP_EP package

Ultrafast SiGe Voltage Comparator (Featuring Reduced Swing PECL Output Drivers) Features: 180 ps propagation delay 25 ps overdrive and slew rate dispersion 8 GHz equivalent input rise time bandwidth 100 ps minimum pulse width 37 ps typical output rise/fall 10 ps deterministic jitter (DJ) 200 fs random jitter (RJ) −2 V to +3 V input range with +5 V/−5 V supplies On-chip terminations at both input pins Resistor-programmable hysteresis Differential latch control Power supply rejection > 70 dB

Dual Channel, Configurable, IsolatedDigital Input Features: Dual channel, configurable, isolated digital input Programmable trip threshold On-chip debounce filter On-chip data and power Isolation Application circuit monitors wide voltage range 10 V dc to 300 V dc 8 V rms to 240 V rms ac (with 10 ms + pickup) Negative dc protected Programmable wetting current Pulse up to 50 mA Constant current up to 6.3 mA Safety and regulatory approvals UL recognition 3750 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice #5A (pending) CSA 61010-1: 300 V rms VDE certificate of conformity (pending) DIN V VDE V 0884-11 (VDE V 0884-11):2017-1 VIORM = 565 V peak EMC robust solution supports relay protection system level requirements ADC samples available for system diagnostics Internal SAR ADC with PGA Single 3.3 V Supply Integrated isoPower, isolated dc-to-dc converter Interfaces SPI DOUTx output reflects state of digital input IRQ interrupt pin Operating temperature: −40°C to +125°C 20-lead, LGA package with 6.8 mm creepage

High Performance Polyphase Energy Measurement IC Features: 7 high performance analog-to-digital converters (ADCs) 101 dB signal-to-noise ratio (SNR) 10,000:1 dynamic range Wide input range: ±1 V, 0.707 V rms full scale Differential inputs ±25 ppm/°C maximum channel temperature drift (including ADC, internal VREF, and PGA drift) enabling Class 0.2 meters with standard external components Power quality measurements Line frequency: 1 measurement per phase Zero crossing detection, zero-crossing timeout Phase angle measurements Supports current transformers (CTs) and Rogowski coil (di/dt) sensors Multiple range phase/gain compensation for CTs Digital integrator for Rogowski coils Flexible waveform buffer Able to resample waveform to ensure 64 points per line cycle for ease of external harmonic analysis Events can trigger waveform storage Simplifies data collection for IEC 61000-4-7 harmonic analysis Advanced metrology feature set Total active power, volt-amperes reactive (VAR), volt-amperes (VA), watthour, VAR-hour, and VA-hour Fundamental VAR and VAR-hour Current and voltage rms per phase (xIRMS, xVRMS) Supports active energy standards: IEC 62053-21, IEC 62053-22; EN50470-3; OIML R46, ANSI C12.20 Supports reactive energy standards: IEC 62053-23, IEC 62053-4 High speed communication port 10 MHz serial peripheral interface (SPI)

Multichannel ISM Band FSK/GFSK/OOK/GOOK/ASK Transmitter Features: Single-chip, low power UHF transmitter 75 MHz to 1 GHz frequency operation Multichannel operation using fractional-N PLL 2.3 V to 3.6 V operation On-board regulator Programmable output power −16 dBm to +14 dBm, 0.4 dB steps Data rates: dc to 179.2 kbps Low current consumption 868 MHz, 10 dBm, 21 mA 433 MHz, 10 dBm, 17 mA 315 MHz, 0 dBm, 10 mA Programmable low battery voltage indicator 24-lead TSSOP

Fixed Frequency SOT-23 Oscillator Features: No External Components to Set Frequency Frequency Error ±0.5% Typical Fast Start-Up Time: 100µs Typical ±20ppm/°C Temperature Stability Includes Output Enable Includes Divide by 1, 2 or 4 Rise Time: 0.5ns, CL = 5pF Timing Jitter: <0.8% Typical Duty Cycle: 50% ±2.5% IS = 8mA Typical (fOSC = 100MHz, CL = 5pF) CMOS Output Drives 600Ω Load Single Supply 2.7V to 5.5V Low Profile (1mm) ThinSOT™ Package

16-/14-/11-Bit 2.5Gsps DACs Features:80dBc SFDR at 70MHz fOUT>68dBc SFDR from DC to 1000MHz fOUT40mA Nominal Full-Scale, ±1V Output Compliant10mA to 60mA Adjustable Full-Scale Current RangeSingle or Dual Port DDR LVDS and DHSTL InterfaceLow Latency (7.5 Cycles for Single Port, 11 Cycles for Dual Port)>78dBc 2-Tone IMD from DC to 1000MHz fOUT–165dBc/Hz Additive Phase Noise at 1MHz Offset for 65MHz fOUT170-Lead (9mm × 15mm) BGA Package

Backup Battery Controller with Fixed Output Features: Not Recommended For New Designs. Contact Analog Devices for Potential Replacement. Complete Battery Backup System in an SO-8, 16-Pin GN or SO Package Generates Fixed Backup Voltage (3.07V/4.63V) from a Single 1.2V NiCd Button Cell Automatic Main Supply to Backup Switching Minimum 100mW Output Power Automatic Fast Recharge of NiCd Battery Programmable NiCd Trickle Charge Current Smart NiCd Charger Minimizes Recharge Time and Maximizes System Efficiency After Backup Onboard Power-Up and Push-Button Reset Generator Performs VCC Supervisory Functions Reset Assertion Guaranteed at VCC = 1V Short-Circuit Protection Thermal Limiting

High Efficiency Bidirectional Multicell Battery Balancer Features: Bidirectional Synchronous Flyback Balancing of Up to 6 Li-Ion or LiFePO4 Cells in Series Up to 10A Balancing Current (Set by Externals) Integrates Seamlessly with the LTC680x Family of Multicell Battery Stack Monitors Bidirectional Architecture Minimizes Balancing Time and Power Dissipation Up to 92% Charge Transfer Efficiency Stackable Architecture Enables >1000V Systems Uses Simple 2-Winding Transformers 1MHz Daisy-Chainable Serial Interface with 4-Bit CRC Packet Error Checking High Noise Margin Serial Communication Numerous Fault Protection Features 48-Lead Exposed Pad QFN and LQFP Packages AEC-Q100 Qualified for Automotive Applications

PolyPhaseSynchronous Boost Controller with Input/Output Protection Features: Input Supply Range: 4.5V to 65V (Up to 75V Surge) Reverse Input Protection to –40V In-Rush Current Control, Overcurrent Protection and Output Disconnect for Boost Converter Input Voltage Surge Protection with Adjustable Clamp Voltage Onboard Ideal Diode Controller Low Quiescent Current: 55µA 2-Phase Operation Reduces Required Input and Output Capacitance and Noise Output Voltage Up to 60V Adjustable Gate Drive Level 5V to 10V (OPTI-DRIVE) for Logic-Level or Standard Threshold FETs No External Bootstrap Diodes Required