Isolated, Synchronous Forward Controller with Active Clamp and iCoupler Features: Current mode controller for active clamp forward topology Integrated 5 kV (wide body SOIC package) or 3.0 kV (LGA package) rated dielectric isolation voltage with Analog Devices, Inc., patented iCoupler technology Wide voltage supply range Primary VIN: up to 60 V Secondary VDD2: up to 36 V Integrated 1 A primary side MOSFET driver for power switch and active clamp reset switch Integrated 1 A secondary side MOSFET drivers for synchronous rectification Integrated error amplifier and <1% accurate reference voltage Programmable slope compensation Programmable frequency range: 50 kHz to 600 kHz typical Frequency synchronization Programmable maximum duty cycle limit Programmable soft start Smooth soft start from precharged load Programmable dead time Power saving light load mode using MODE pin Protection features such as short circuit, output overvoltage, and overtemperature protection Cycle-by-cycle input overcurrent protection Precision enable UVLO with hysteresis PGOOD pin for system flagging Tracking function from secondary side Remote (secondary side) shutdown/reset function Safety and regulatory approvals (pending) UL recognition 5000 V rms for 1 minute per UL 1577 (for wide body SOIC package) 3000 V rms for 1 minute per UL 1577 (for LGA package) CSA component acceptance notice 5A VDE certificate of conformity DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 VIORM = 849 V peak (for wide body SOIC package) VIORM = 560 V peak (for LGA package) CQC certification per GB4943.1-2011 Available in 24-lead SOIC_W package and 24-terminal LGA package AEC-Q100 Qualified for Automotive Applications

Ultralow Noise, 150 mA CMOS Linear Regulator Features: Chinese data sheet available Ultralow noise: 9 μV rms, independent of VOUT No additional noise bypass capacitor required Stable with 1 μF ceramic input and output capacitors Maximum output current: 150 mA Input voltage range: 2.2 V to 5.5 V Low quiescent current IGND = 10 μA with zero load Low shutdown current: <1 μA Low dropout voltage: 105 mV at 150 mA load Initial output voltage accuracy: ±1% Up to 14 fixed output voltage options: 1.8 V to 3.3 V PSRR performance of 70 dB at 10 kHz Current limit and thermal overload protection Logic-controlled enable 5-lead TSOT package 4-ball, 0.8 mm × 0.8 mm, 0.4 mm pitch WLCSP AEC-Q100 qualified for automotive applications

150 mA, Low Dropout, CMOS Linear Regulator Features: Maximum output current: 150 mA Input voltage range: 2.5 V to 5.5 V Light load efficient IGND = 35 μA with zero load IGND = 40 μA with 100 μA load Low shutdown current: <1 μA Low dropout voltage: 150 mV @ 150 mA load Initial accuracy: ±1% Accuracy over line, load, and temperature: ±2% Stable with small 1 μF ceramic output capacitor 16 fixed output voltage options: 0.75 V to 3.3 V (ADP1710) Adjustable output voltage option: 0.8 V to 5.0 V (ADP1710 Adjustable) 16 fixed output voltage options with reference bypass: 0.75 V to 3.3 V (ADP1711) High PSRR: 69 dB @ 1 kHz

300 mA, Low Dropout CMOS Linear Regulator Features: Maximum output current: 300 mA Input voltage range: 2.5 V to 5.5 V Light load efficient IGND = 75 μA with 100 μA load Low shutdown current: <1 μA Very low dropout voltage: 170 mV @ 300 mA load Initial accuracy: ±1% Accuracy over line, load, and temperature: ±2% 16 fixed output voltage options with tracking: 0.75 V to 3.3 V Low output noise: 40 μV rms High PSRR: 72 dB @ 1 kHz Stable with small 2.2 μF ceramic output capacitor See data sheet for additional features

Bridge Sensor Signal Conditioner IC with LIN Interface, Nonlinearity Correction, Temperature Compensation Features:LIN 2.1 compliant interface (bridge sensor signal, temperature)Digitally programmable gain and offset voltage adjustmentGain range from 2.94 V/V to 971.10 V/VSensor temperature compensation (first- or second-order)Sensor nonlinearity correction (first- or second-order)Internal or external temperature sensor compensationEEPROM nonvolatile memory for calibration dataHigh system accuracy: 0.1% FSR over temperatureEMC and EMI protectionFault protection for open circuits and short circuits4 mm 4 mm, 20-lead LFCSP6 V to 18 V supply operation40C to +150C operating temperature rangeAEC-Q100 qualified for automotive applications

Integrated AMR Angle Sensor and Signal Conditioner with Differential Outputs Features: Contactless angular measurement High precision 180° angle sensor Typical angular error of ±0.1° Low output noise of 850 μV rms Sine and cosine differential outputs Ratiometric analog voltage outputs Negligible hysteresis SAR or Σ-Δ ADC compatible Temperature compensated AMR bridge Industrial temperature range: −40°C to +125°C Automotive temperature range: −40°C to +150°C EMI resistant Fault diagnostics VDD from 2.7 V to 5.5 V Minimal phase error of 0.85° at 30,000 rpm AEC-Q100 qualified for automotive applications Single chip solution Available in an 8-lead SOIC package

Integrated AMR Angle Sensor and Signal Conditioner with Differential Outputs Features: Contactless angular measurement High precision 180° angle sensor Typical angular error of ±0.1° Low output noise of 850 μV rms Sine and cosine differential outputs Ratiometric analog voltage outputs Negligible hysteresis SAR or Σ-Δ ADC compatible Temperature compensated AMR bridge Industrial temperature range: −40°C to +125°C Automotive temperature range: −40°C to +150°C EMI resistant Fault diagnostics VDD from 2.7 V to 5.5 V Minimal phase error of 0.85° at 30,000 rpm AEC-Q100 qualified for automotive applications Single chip solution Available in an 8-lead SOIC package

16-Bit, 15 MSPS, Module Data Acquisition Solution Features: Integrated fully differential ADC driver with signal scaling Wide input common range High common-mode rejection Single-ended to differential conversion 2.048 V input range with 4.096 V REFBUF Critical passive components 0.005% precision matched resistor array for FDA 9 mm × 9 mm, 0.8 mm pitch, 100-ball BGA package 4× footprint reduction versus discrete solution Low power, dynamic power scaling, power-down mode 143 mW typical at 15 MSPS Throughput: 15 MSPS, no pipeline delay INL: 0.4 LSB typical, 1 LSB maximum SINAD: 89 dB typical at 1 kHz THD: 115 dB at 1 kHz, 106 dB at 400 kHz Gain error: 0.005% FS typical Gain error drift: 1 ppm/C maximum On-board reference buffer with VCMO generation Serial LVDS interface Wide operating temperature range: 40C to +85C

10 GHz to 40 GHz, 1:4 Channel, 4 Frequency Multiplier/Filter Features: 4 input frequency multiplier with programmable harmonic filter Quad Differential Output PAs with independent Enable Control Input Frequency Range: 2.5 GHz to 10 GHz Output Frequency Range: 10 GHz to 40 GHz Input power: 20 dBm (50 ) Output power: 5 dBm differential (100 ) Harmonic rejection: 20 dBc to 40 dBc at all frequencies 3-Wire or 4-Wire SPI Control of all functions On-Chip Programmable State Machines for fast multiplier/filter and transmitter switching and control On-chip temperature sensor, output power detectors, and ADC DC power: 450 mW (2.5 V supply) 6 mm 6 mm, 40-terminal LGA package

0.5 GHz to 19 GHz Broadband Bi-Directional Single Channel True Time Delay Unit Features:0.5 GHz to 19 GHz frequency rangeProgrammable Time Delay: 7-bit resolutionProgrammable Time Delay ModesTD_Mode0: 0 to 508ps range, 4ps Standard resolutionTD_Mode1: 0 to 254ps range, 2ps High resolutionProgrammable Attenuation: 6-bit resolution31.5 dB adjustment range0.5 dB step sizeFully programmable via a 3-wire or 4-wire SPI interfaceSPI Programmable and Daisy Chaining selectablePower Dissipation: 1 mW with 1.2V and 1.0V Dual Supplies14-pin 2x3mm LFCSP