DC1620A-S: Demo Board for LTC2188 16-Bit, 20Msps Low Power Dual ADC.

The LTC3838 is a dual, PolyPhase? synchronous step-down DC/DC switching regulator controller. Two independent channels drive all N-channel power MOSFETs. The controlled on-time, valley current mode control architecture allows for fast transient response and constant frequency switching in steady-state operation, independent of VIN, VOUT and load current. Its load-release transient detection feature significantly reduces overshoot at low output voltages.Differential output voltage sensing, along with a precision internal reference, offers an accurate ?0.67% output regulation on Channel 1, even if the remote output ground deviates from local ground by ?500mV. The second channel can either provide an independent ?1% output, or together with the first channel of this controller, serve as one of the PolyPhase channels for a single-output voltage.The switching frequency can be programmed from 200kHz to 2MHz with an external resistor, and can be synchronized to an external clock. Very low tON and tOFF times allow for near 0% and near 100% duty cycles, respectively. Voltage tracking soft start-up and multiple safety features are provided.See below for a comparison of LTC3838, LTC3838-1 and LTC3838-2. Part Number Description LTC3838 ? ?0.67% Differential Output Voltage Accuracy Over Temperature on Channel 1, ?1% Output Regulation on Channel 2, Separate Per Channel 30mV to 100mV Current Sense Range Controls LTC3838-1 ? ?0.67% Differential Output Voltage Accuracy Over Temperature on Both Channel 1 and Channel 2, Single Pin 30mV/60mV Current Sense Range Controls LTC3838-2 ?0.67% Differential Output Voltage Accuracy With Internal Reference on Channel 1, ?4mV Differential with External Reference Voltage on Channel 2, Fixed 30mV Current Sense Range Applications Distributed Power Systems Point-of-Load Converters Computing Systems Data Communication Systems

Demonstration circuit 1678A features the LTC2654 Quad 16-bit/12-bit DAC. The LTC2654 is a family of 16-bit/12-bit rail-to-rail DACs with integrated 10ppm/°C maximum reference. The LTC2654 advances performance standards for output drive, crosstalk and load regulation in single supply, voltage-output multiple DACs.

The LTC4280 Hot Swap? controller allows a board to be safely inserted and removed from a live backplane. Using an external N-channel pass transistor, board supply voltage and inrush current are ramped up at an adjustable rate. An I2C interface and onboard ADC allow for monitoring of load current, voltage and fault status.The device features adjustable analog foldback current limit and a FILTER pin which configures the time spent in overcurrent before declaring a fault. An I2C interface may configure the part to latch off or automatically restart after the LTC4280 detects a current limit fault.The controller has additional features to interrupt the host when a fault has occurred, notify when output power is good, detect insertion of a load card, and power-up either automatically upon insertion or wait for an I2C command to turn on.Applications Live Board Insertion Electronic Circuit Breakers Computers, Servers Platform Management

The LTC3226 is a 2-cell series supercapacitor charger with a backup PowerPath controller. It includes a charge pump supercapacitor charger with programmable output voltage, a low dropout regulator, and a power-fail comparator for switching between normal and backup modes.The constant input current supercapacitor charger is designed to charge two supercapacitors in series to a resistor-programmable output voltage from a 2.5V to 5.3V input supply. The charger input current limit is programmable by an external resistor at up to 315mA.The internal backup LDO is powered from the supercapacitors and provides up to 2A peak output current with an adjustable output voltage. When the input supply falls below the power-fail threshold, the LTC3226 automatically enters a backup state in which the supercapacitors power the output through the LDO. The input supply power-fail voltage level is programmed by an external resistor divider.Low input noise, low quiescent current and a compact footprint make the LTC3226 ideally suited for small, batterypowered applications. Internal current limit and thermal shutdown circuitry allow the device to survive a continuous short-circuit from the PROG or CPO pins to ground.Applications Smart Power Meters Battery-Powered Industrial/Medical Equipment 3.3V Solid-State Drives Industrial Alarms Data Backup Supplies Battery Hold-Up Supplies

DC1748A-D: Demo Board for LTM2883 SPI/Digital or I2C μModule Isolator with Adjustable ±12.5V and 5V Regulated Power.

The LT8610 is a compact, high efficiency, high speed synchronous monolithic step-down switching regulator that consumes only 2.5?A of quiescent current. Top and bottom power switches are included with all necessary circuitry to minimize the need for external components. Low ripple Burst Mode operation enables high efficiency down to very low output currents while keeping the output ripple below 10mVP-P. A SYNC pin allows synchronization to an external clock. Internal compensation with peak current mode topology allows the use of small inductors and results in fast transient response and good loop stability. The EN/UV pin has an accurate 1V threshold and can be used to program VIN undervoltage lockout or to shut down the LT8610 reducing the input supply current to 1?A. A capacitor on the TR/SS pin programs the output voltage ramp rate during start-up. The PG flag signals when VOUT is within ?9% of the programmed output voltage as well as fault conditions. The LT8610 is available in a small 16-lead MSOP package with exposed pad for low thermal resistance. Feedback Voltage Min VIN Output Current Notes LT8610AC-1 0.80V 3.0V 3.5A Fsw = 1.5MHz to 2.2MHz, Optimized Transient Response LT8610AC 0.80V 3.0V 3.5A Fsw = 200kHz to 2.2MHz LT8610AB 0.97V 3.4V 3.5A Improved Burst Mode Efficiency LT8610AX 0.97V 3.4V 3.5A 175?C Max Junction Temp LT8610A 0.97V 3.4V 3.5A Higher Iout, 30ns Min On Time LT8610 0.97V 3.4V 2.5A - APPLICATIONS Automotive and Industrial Supplies General Purpose Step-Down GSM Power Supplies

DC1751A-F: Demo Board for the LTM9006-14 14-Bit, 25Msps Low Power Octal ADCs.

The LTC3880/LTC3880-1 are dual, PolyPhase DC/DC synchronous step-down switching regulator controllers with an I2C-based PMBus compliant serial interface. The controllers use a constant frequency, current mode architecture that is supported by LTpowerPlay? software development tool with graphical user interface (GUI).Switching frequency, output voltage, and device address can be programmed using external configuration resistors. Parameters can be set via the digital interface or stored in EEPROM. Voltage, current, internal/external temperature and fault status can be read back through the bus interface. The LTC3880 incorporates a 5V linear regulator while the LTC3880-1 uses an external 5V supply for minimum power loss. See comparison to LTC3887 below. VOUT Start-Up Time Max VOUT0/1 Fast ADC Mode for 1 Parameter LTC3887/LTC3887-1 35ms 5.5V/5.5V No LTC3880/LTC3880-1 120ms 4V/5.4V No Applications High Current Distributed Power Systems Telecom, Datacom and Storage Systems Intelligent Energy Efficient Power Regulation

Demonstration circuit 1780A-A features PolyPhase® design using the LTM4620EV, the high efficiency, high density, dual 13A, switch mode step-down power module regulator. The input voltage is from 4.5V to 16V. The output voltage is jumper selectable from 1.0V to 2.5V. DC1780A-A can deliver nominal 50A output current with 2× LTM4620s in parallel. As explained in the data sheet, output current derating is necessary for certain VIN, VOUT, and thermal conditions.