Precision Analog Microcontroller, Tunable Optical Control Microcontroller Features: Analog input/output 22-channel, 14-bit, 800 kSPS analog-to-digital converter (ADC) 10 external channels 1 on-chip die temperature monitor 6 current output digital-to-analog converter (IDAC) monitor channels 3 power monitor channels 2 buffered reference output channels Fully differential and single-ended modes 0 V to 2.5 V analog input range 6 low noise, 12-/14-bit IDAC outputs 1× 250 mA, 1× 200 mA, 2× 100 mA, and 2× 20 mA Semiconductor optical amplifier (SOA) IDAC pull-down to −3.0 V for fast current sink Eight 12-bit voltage output DACs (VDACs) Channel 0 and Channel 1: 0 V to 3 V, 75 Ω load Channel 2 and Channel 3: −5 V to 0 V, 500 Ω load Channel 4 and Channel 5: 0 V to 3 V, 300 Ω load Channel 6: 0 V to 5 V, 500 Ω load Channel 7: 0 V to 5 V, 100 Ω load 2.5 V, on-chip voltage reference 2 buffered 2.5 V outputs Microcontroller ARM Cortex-M3 processor, 32-bit RISC architecture Serial wire port supports code download and debugging Clocking options Trimmed on-chip oscillator (±3%) 80 MHz phase-locked loop (PLL) External 16 MHz crystal option External clock source Memory 2× 128 kB Flash/EE memories, 32 kB SRAM In-circuit download, SW-DP-based debugging Software triggered in-circuit reprogrammability On-chip peripherals UART, 2× I2C and 2× SPI serial input/output 28-pin general-purpose input/output (GPIO) port 3 general-purpose timers Wake-up (W/U) timer Watchdog timer (WDT) 32-element programmable logic array (PLA) Vectored interrupt controller Interrupt on edge or level external pin inputs 9× external interrupts Power Multiple supplies 5 V for VDAC6 and VDAC7 3.3 V for digital and analog inputs/outputs 1.8 V to 2.7 V for IDACs −5 V supply for IDAC3 and VDAC2/VDAC3 Package and temperature range 6 mm × 6 mm, 112-ball CSP_BGA package Fully specified for −40°C to +85°C ambient operation Tools QuickStart™ development system Full third party support

The ADuCM310 is a multidie stack, on-chip system designed for diagnostic control of tunable laser

Precision Analog Microcontroller, Tunable Optical Control Microcontroller Features: Analog input/output 22-channel, 14-bit, 800 kSPS analog-to-digital converter (ADC) 10 external channels 1 on-chip die temperature monitor 6 current output digital-to-analog converter (IDAC) monitor channels 3 power monitor channels 2 buffered reference output channels Fully differential and single-ended modes 0 V to 2.5 V analog input range 6 low noise, 12-/14-bit IDAC outputs 1× 250 mA, 1× 200 mA, 2× 100 mA, and 2× 20 mA Semiconductor optical amplifier (SOA) IDAC pull-down to −3.0 V for fast current sink Eight 12-bit voltage output DACs (VDACs) Channel 0 and Channel 1: 0 V to 3 V, 75 Ω load Channel 2 and Channel 3: −5 V to 0 V, 500 Ω load Channel 4 and Channel 5: 0 V to 3 V, 300 Ω load Channel 6: 0 V to 5 V, 500 Ω load Channel 7: 0 V to 5 V, 100 Ω load 2.5 V, on-chip voltage reference 2 buffered 2.5 V outputs Microcontroller ARM Cortex-M3 processor, 32-bit RISC architecture Serial wire port supports code download and debugging Clocking options Trimmed on-chip oscillator (±3%) 80 MHz phase-locked loop (PLL) External 16 MHz crystal option External clock source Memory 2× 128 kB Flash/EE memories, 32 kB SRAM In-circuit download, SW-DP-based debugging Software triggered in-circuit reprogrammability On-chip peripherals UART, 2× I2C and 2× SPI serial input/output 28-pin general-purpose input/output (GPIO) port 3 general-purpose timers Wake-up (W/U) timer Watchdog timer (WDT) 32-element programmable logic array (PLA) Vectored interrupt controller Interrupt on edge or level external pin inputs 9× external interrupts Power Multiple supplies 5 V for VDAC6 and VDAC7 3.3 V for digital and analog inputs/outputs 1.8 V to 2.7 V for IDACs −5 V supply for IDAC3 and VDAC2/VDAC3 Package and temperature range 6 mm × 6 mm, 112-ball CSP_BGA package Fully specified for −40°C to +85°C ambient operation Tools QuickStart™ development system Full third party support

The ADuCM310 is a multidie stack, on-chip system designed for diagnostic control of tunable laser

Digital Isolator, Enhanced System-Level ESD Reliability

Triple-Channel Digital Isolators

Configurable Impedance Network Analyzer & Potentiostat with Integrated Cortex M3 Core Features: Analog performance 160 kSPS, 16-bit, precision analog-to-digital converter (ADC) 4 dedicated voltage measurement channels 8 current measurement channels Impedance measurement engine High precision voltage reference Supply noise rejection filtering Ultralow leakage configurable switch matrix 12-bit digital-to-analog converter (DAC) Precision instrumentation amplifier control loop 6-channel CapTouch controller Temperature sensor Analog hardware accelerators Autonomous analog front-end (AFE) controller Independent sequencer for AFE functions Direct digital synthesizer (DDS)/arbitrary waveform generator Receive filters Complex impedance measurement (DFT) engine Processing 16 MHz ARM Cortex-M3 processor 384 kB of embedded flash memory 32 kB system SRAM 16 kB Flash configured EEPROM Integrated full-speed USB 2.0 controller and PHY Multilayer advanced microcontroller bus architecture (AMBA) bus matrix Central direct memory access (DMA) controller Real-time clock (RTC) General-purpose, wake-up, and watchdog timers Communication Input/output I2S and beeper interface LCD display controller (parallel and serial) LCD segment controller SPI, I2C, and UART peripheral interfaces Programmable GPIOs Power Coin cell battery compatible 2.5 V to 3.6 V active measurement range Power management unit (PMU) Power-on reset (POR) and power supply monitor (PSM) Packages and temperature range Operating temperature range: −40°C to +85°C Package: 120-lead, 8 mm × 8 mm CSP_BGA 

Configurable Impedance Network Analyzer & Potentiostat with Integrated Cortex M3 Core Features: Analog performance 160 kSPS, 16-bit, precision analog-to-digital converter (ADC) 4 dedicated voltage measurement channels 8 current measurement channels Impedance measurement engine High precision voltage reference Supply noise rejection filtering Ultralow leakage configurable switch matrix 12-bit digital-to-analog converter (DAC) Precision instrumentation amplifier control loop 6-channel CapTouch controller Temperature sensor Analog hardware accelerators Autonomous analog front-end (AFE) controller Independent sequencer for AFE functions Direct digital synthesizer (DDS)/arbitrary waveform generator Receive filters Complex impedance measurement (DFT) engine Processing 16 MHz ARM Cortex-M3 processor 384 kB of embedded flash memory 32 kB system SRAM 16 kB Flash configured EEPROM Integrated full-speed USB 2.0 controller and PHY Multilayer advanced microcontroller bus architecture (AMBA) bus matrix Central direct memory access (DMA) controller Real-time clock (RTC) General-purpose, wake-up, and watchdog timers Communication Input/output I2S and beeper interface LCD display controller (parallel and serial) LCD segment controller SPI, I2C, and UART peripheral interfaces Programmable GPIOs Power Coin cell battery compatible 2.5 V to 3.6 V active measurement range Power management unit (PMU) Power-on reset (POR) and power supply monitor (PSM) Packages and temperature range Operating temperature range: −40°C to +85°C Package: 120-lead, 8 mm × 8 mm CSP_BGA 

Precision Analog Microcontroller, 16-Bit Analog Input/Output with MDIO Interface, Arm Cortex-M33 Features: Analog input/output Multichannel, 16-bit, 2 MSPS ADC Up to 16 external channels On-chip die temperature monitor 4 power monitor channels 4 PGA/TIA channels supporting voltage and current measurements Fully differential and single-ended modes 0 V to VREF analog input range 12-bit voltage output DACs 8× 0 V to 2.5 V, 1 kΩ load 4× 0 V to 2.5 V, 2.5 kΩ load On-chip low drift voltage reference, 1.25 V or 2.5 V Buffered 1.25 V or 2.5 V output 4 voltage comparators Microcontroller 32-bit Arm Cortex-M33 core, 32-bit RISC architecture, FPU Serial wire port supports code download and debug Clocking options 16 MHz on-chip oscillator 160 MHz PLL output with programmable divider External clock source Memory 2× 512 kB independent Flash/EE memories 10,000-cycle Flash/EE endurance 20-year Flash/EE retention 128 kB SRAM with ECC Software triggered, in circuit reprogrammability via MDIO or I2C On-chip peripherals 2× UART, 3× SPI, 3× I2C serial input/output Multilevel voltage (3.3 V, 1.8 V, 1.2 V) GPIOs MDIO slave up to 10 MHz 5 general-purpose timers Wake-up timer (WUTs) Watchdog timers (WDTs) 32-element PLA 16-bit PWM 10 external Interrupts Power Multiple supplies: 3.3 V for voltage DACs and ADCs, and 3.3 V, 1.8 V, or 1.2 V for digital inputs/outputs Flexible operating modes for low power applications Packages and temperature range 5 mm × 5 mm 81-ball CSP_BGA and 3.46 mm × 3.46 mm 64-ball WLCSP BGA package uses ULA molding compounds Fully specified for −40°C to +105°C operation Tools Low cost quick start development system Full third-party support  

Precision Analog Microcontroller, 16-Bit Analog Input/Output with MDIO Interface, Arm Cortex-M33 Features: Analog input/output Multichannel, 16-bit, 2 MSPS ADC Up to 16 external channels On-chip die temperature monitor 4 power monitor channels 4 PGA/TIA channels supporting voltage and current measurements Fully differential and single-ended modes 0 V to VREF analog input range 12-bit voltage output DACs 8× 0 V to 2.5 V, 1 kΩ load 4× 0 V to 2.5 V, 2.5 kΩ load On-chip low drift voltage reference, 1.25 V or 2.5 V Buffered 1.25 V or 2.5 V output 4 voltage comparators Microcontroller 32-bit Arm Cortex-M33 core, 32-bit RISC architecture, FPU Serial wire port supports code download and debug Clocking options 16 MHz on-chip oscillator 160 MHz PLL output with programmable divider External clock source Memory 2× 512 kB independent Flash/EE memories 10,000-cycle Flash/EE endurance 20-year Flash/EE retention 128 kB SRAM with ECC Software triggered, in circuit reprogrammability via MDIO or I2C On-chip peripherals 2× UART, 3× SPI, 3× I2C serial input/output Multilevel voltage (3.3 V, 1.8 V, 1.2 V) GPIOs MDIO slave up to 10 MHz 5 general-purpose timers Wake-up timer (WUTs) Watchdog timers (WDTs) 32-element PLA 16-bit PWM 10 external Interrupts Power Multiple supplies: 3.3 V for voltage DACs and ADCs, and 3.3 V, 1.8 V, or 1.2 V for digital inputs/outputs Flexible operating modes for low power applications Packages and temperature range 5 mm × 5 mm 81-ball CSP_BGA and 3.46 mm × 3.46 mm 64-ball WLCSP BGA package uses ULA molding compounds Fully specified for −40°C to +105°C operation Tools Low cost quick start development system Full third-party support