The AD8341 vector modulator performs arbitrary amplitudeand phase modulation of an RF signal. Because the RF signalpath is linear, the original modulation is preserved. This part canbe used as a general-purpose RF modulator, a variable attenuator/phase shifter, or a remodulator. The amplitude can be controlledfrom a maximum of ?4.5 dB to less than ?34.5 dB, and the phasecan be shifted continuously over the entire 360? range. For maximumgain, the AD8341 delivers an OP1dB of 8.5 dBm, an OIP3of 17.5 dBm, and an output noise floor of ?150.5 dBm/Hz,independent of phase. It operates over a frequency range of1.5 GHz to 2.4 GHz.The baseband inputs in Cartesian I and Q format control theamplitude and phase modulation imposed on the RF inputsignal. Both I and Q inputs are dc-coupled with a ?500 mVdifferential full-scale range. The maximum modulationbandwidth is 230 MHz, which can be reduced by adding externalcapacitors to limit the noise bandwidth on the control lines.Both the RF inputs and outputs can be used differentially orsingle-ended and must be ac-coupled. The RF input and outputimpedances are nominally 50 ? over the operating frequencyrange. The DSOP pin allows the output stage to be disabledquickly in order to protect subsequent stages from overdrive.The AD8341 operates off supply voltages from 4.75 V to 5.25 Vwhile consuming approximately 125 mA.The AD8341 is fabricated on Analog Devices? proprietary, highperformance 25 GHz SOI complementary bipolar IC process. Itis available in a 24-lead, lead-free LFCSP package and operatesover a ?40?C to +85?C temperature range. Evaluation boardsare available. Applications RF PA linearization/RF predistortion Amplitude and phase modulation Variable attenuators and phase shifters CDMA2000, WCDMA, GSM/EDGE linear power amplifiers Smart antennasAvailabilitySamples part number AD8341ACP and an evaluation board, part number AD8341-EVAL, are available.Companion ProductsAD8302 - LF - 2.7GHz RF/IF Gain Phase DetectorAD8340 - RF Vector Modulator 700MHz to 1000MHzOther Modulator / Demodulator ProductsAD8345 - 250MHz to 1000MHz Low Noise RF/IF ModulatorAD8346 - 800MHz to 2.5GHz Lower Power Direct Up-Conversion ModulatorAD8347 - 800MHz to 2.7GHz Direct Conversion DemodulatorAD8348 - 50MHz to 1000MHz RF/IF Quadrature DemodulatorAD8349 - 700MHz - 2.7GHz Low Noise Direct Up Conversion Modulator

The AD8361 is a mean-responding power detector for use inhigh frequency receiver and transmitter signal chains, up to2.5 GHz. It is very easy to apply. It requires a single supply onlybetween 2.7 V and 5.5 V, a power supply decoupling capacitor,and an input coupling capacitor in most applications. Theoutput is a linear-responding dc voltage with a conversion gainof 7.5 V/V rms. An external filter capacitor can be added toincrease the averaging time constant.The AD8361 is intended for true power measurement of simpleand complex waveforms. The device is particularly useful formeasuring high crest-factor (high peak-to-rms ratio) signals,such as CDMA and W-CDMA.The AD8361 has three operating modes to accommodate avariety of analog-to-digital converter requirements: Ground reference mode, in which the origin is zero. Internal reference mode, which offsets the output 350 mV above ground. Supply reference mode, which offsets the output to VS/7.5.The AD8361 is specified for operation from ?40?C to +85?Cand is available in 8-lead MSOP and 6-lead SOT-23 packages. Itis fabricated on a proprietary high fT silicon bipolar process.

The AD8364 is a true rms, responding, dual-channel RF powermeasurement subsystem for the precise measurement and controlof signal power. The flexibility of the AD8364 allows communicationssystems, such as RF power amplifiers and radio transceiverAGC circuits, to be monitored and controlled with ease. Operatingon a single 5 V supply, each channel is fully specified for operationup to 2.7 GHz over a dynamic range of 60 dB. The AD8364provides accurately scaled, independent, rms outputs of both RFmeasurement channels. Difference output ports, which measurethe difference between the two channels, are also available. Theon-chip channel matching makes the rms channel differenceoutputs extremely stable with temperature and process variations.The device also includes a useful temperature sensor with anaccurately scaled voltage proportional to temperature, specifiedover the device operating temperature range. The AD8364 canbe used with input signals having rms values from ?55 dBm to+5 dBm referred to 50 ? and large crest factors with noaccuracy degradation. Integrated in the AD8364 are two matched AD8362 channels(see the AD8362 data sheet for more information) with improvedtemperature performance and reduced log conformance ripple.Enhancements include improved temperature performance andreduced log-conformance ripple compared to the AD8362. On-chipwide bandwidth output operational amplifiers are connectedto accom-modate flexible configurations that support manysystem solutions.The device can easily be configured to provide four rmsmeasurements simultaneously. Linear-in-dB rms measurementsare supplied at OUTA and OUTB, with conveniently scaledslopes of 50 mV/dB. The rms difference between OUTA andOUTB is available as differential or single-ended signals atOUTP and OUTN. An optional voltage applied to VLVLprovides a common mode reference level to offset OUTP andOUTN above ground.The AD8364 is supplied in a 32-lead, 5 mm ? 5 mm LFCSP, forthe operating temperature of ?40?C to +85?C.Applications Wireless infrastructure power amplifier linearization/control Antenna VSWR monitor Gain and power control and measurement Transmitter signal strength indication (TSSI) Dual-channel wireless infrastructure radios

The AD8368 is a variable gain amplifier (VGA) with analog linear-in-dB gain control that can be used from low frequencies to 800 MHz. Its excellent gain range, conformance, and flatness are attributed to the Analog Devices, Inc. X-AMP? architecture, an innovative technique for implementing high performance variable gain control.The gain range of ?12 dB to +22 dB is scaled accurately to 37.5 dB/V with excellent conformance error. The AD8368 has a 3 dB bandwidth of 800 MHz that is nominally independent of gain setting. At 140 MHz, the OIP3 is 33 dBm at maximum gain. The output noise floor is ?143 dBm/Hz, which corresponds to a 9.5 dB noise figure at maximum gain. The single-ended input and output impedances are nominally 50 ?.The gain of the AD8368 can be configured to be an increasing or decreasing function of the gain control voltage depending on whether the MODE pin is pulled to the positive supply or to ground, respectively. When MODE is pulled high, the AD8368 operates as a typical VGA with increasing gain.By connecting MODE to ground and using the on-board rms detector, the AD8368 can be configured as a complete automatic gain control (AGC) system with RSSI. The output power is accurately leveled to the internal default setpoint of 63 mV rms (?11 dBm referenced to 50 ?), independent of the waveform crest factor. Because the uncommitted detector input is available at DETI, the AGC loop can level the signal at the AD8368 output or at any other point in the signal chain over a maximum input power range of 34 dB. Furthermore, the setpoint level can be raised by dividing down the output signal before applying it to the detector.The AD8368 operates from a supply voltage of 4.5 V to 5.5 V and consumes 60 mA of current. It can be fully powered down to <3 mA by grounding the ENBL pin. The AD8368 is fabricated using the Analog Devices proprietary SiGe SOI complementary bipolar IC process. It is available in a 24-lead LFCSP and operates over the industrial temperature range of ?40?C to +85?C. Application boards are available upon request.ApplicationsComplete IF AGC amplifiers Gain trimming and leveling Cellular base stations Point-to-point radio links RF instrumentation Data Sheet, Rev. B, 09/2008

The AD8372 is a dual, digitally controlled, variable gainamplifier (VGA) that provides precise gain control, high IP3,and low noise figure. The excellent distortion performance andmoderate signal bandwidth make the AD8372 a suitable gain control device for a variety of multichannel receiverapplications.For wide input dynamic range applications, the AD8372provides a broad 41 dB gain range. The gain is programmedthrough a bidirectional 4-pin serial interface. The serial interface consists of a clock, latch, data input, and data output linesfor each channel. The AD8372 provides the ability to set the transconductance of the output stage using a single external resistor. The RXT1 and RXT2 pins provide a band gap derived stable reference voltage of 1.56 V. Typically 2.0 k? shunt resistors to ground are used toset the maximum gain to a nominal value of 31 dB. The currentsetting resistors can be adjusted to manipulate the gain anddistortion performance of each channel. This is a flexible feature in applications where it is desirable to trade off distortion performance for lower power consumption.The AD8372 is powered on by applying the appropriate logiclevel to the ENB1, ENB2 pins. When powered down, the AD8372consumes less than 2.6 mA and offers excellent input-to-outputisolation. The gain setting is preserved when powered down.Fabricated on an Analog Devices, Inc., high frequency BiCMOS process, the AD8372 provides precise gain adjustment capabilities with good distortion performance. The quiescent current of theAD8372 is typically 106 mA per channel. The AD8372 amplifier comes in a compact, thermally enhanced 5 mm ? 5 mm 32-leadLFCSP package and operates over the temperature range of ?40?C to +85?C.Applications Differential ADC drivers CMTS upstream direct sampling receivers CATV modem signal scaling Generic RF/IF gain stages Single-ended-to-differential conversion

The AD8418 is a high voltage, high resolution current shunt amplifier. It features an initial gain of 20 V/V, with a maximum ?0.15% gain error over the entire temperature range. The buffered output voltage directly interfaces with any typical converter. The AD8418 offers excellent input common-mode rejection from ?2 V to +70 V. The AD8418 performs bidirectional current measurements across a shunt resistor in a variety of automotive and industrial applications, including motor control, battery management, and solenoid control.The AD8418 offers breakthrough performance throughout the ?40?C to +125?C temperature range. It features a zero drift core, which leads to a typical offset drift of 0.1 ?V/?C throughout the operating temperature range and the common-mode voltage range. The AD8418 is fully qualified for automotive applications and includes EMI filters and patented circuitry to enable output accuracy with pulse-width modulation (PWM) type input common-mode voltages. The typical input offset voltage is ?200 ?V. The AD8418 is offered in 8-lead MSOP and SOIC packages.Applications High-side current sensing in Motor controls Solenoid controls Power management Low-side current sensing Diagnostic protection

The AD8479 is a difference amplifier with a very high inputcommon-mode voltage range. The AD8479 is a precision devicethat allows the user to accurately measure differential signals inthe presence of high common-mode voltages up to ?600 V.The AD8479 can replace costly isolation amplifiers in applicationsthat do not require galvanic isolation. The device operates overa ?600 V common-mode voltage range and has inputs that areprotected from common-mode or differential mode transientsup to ?600 V.The AD8479 has low offset voltage, low offset voltage drift, low gain drift, low common-mode rejection drift, and excellent common-mode rejection ratio (CMRR) over a wide frequency range.The AD8479 is available in a space-saving 8-lead SOIC package and is operational over the ?40?C to +125?C temperature range.Applications High voltage current sensing Battery cell voltage monitors Power supply current monitors Motor controls Isolation

The AD8556 is a zero-drift, sensor signal amplifier withdigitally programmable gain and output offset. Designed toeasily and accurately convert variable pressure sensor andstrain bridge outputsto a well-defined output voltage range,the AD8556 accurately amplifies many other differential orsingle-ended sensor outputs. The AD8556 uses the ADIpatented low noise auto-zero and DigiTrim? technologies tocreate an incredibly accurate and flexible signal processingsolution in a very compact footprint.Gain is digitally programmable in a wide range from 70 to1,280 through a serial data interface. Gain adjustment canbe fully simulated in-circuit and then permanently programmedwith reliable polyfuse technology. Output offsetvoltage is also digitally programmable and is ratiometric to thesupply voltage. AD8556 also features internal EMI filters on theVNEG, VPOS, FILT and VCLAMP pins.In addition to extremely low input offset voltage, low inputoffset voltage drift, and very high dc and ac CMRR, the AD8556 also includes a pull-up current source at the input pinsand a pull-down current source at the VCLAMP pin. Thisallows open wire and shorted wire fault detection. A low-passfilter function is implemented via a single low cost externalcapacitor. Output clamping set via an external reference voltageallows the AD8556 to drive lower voltage ADCs safely andaccurately.When used in conjunction with an ADC referenced to the samesupply, the system accuracy becomes immune to normal supplyvoltage variations. Output offset voltage can be adjusted with aresolution of better than 0.4% of the difference between VDDand VSS. A lockout trim after gain and offset adjustmentfurther ensures field reliability.The AD8556 is fully specified from ?40?C to +140?C.Operating from single-supply voltages of 2.7 V to 5.5 V, theAD8556 is offered in the 8-lead SOIC_N, and 4 mm ? 4 mm16-lead LFCSP_VQ.ApplicationsAutomotive SensorsPressure and Position SensorsPrecision Current SensingStrain Gages

The AD9081 mixed signal front end (MxFE?) is a highly integrated device with four 16-bit, 12 GSPS maximum sample rate, RF digital-to-analog converter (DAC) cores, and four 12-bit, 4 GSPS rate, RF analog-to-digital converter (ADC) cores. The AD9081 is well suited for applications requiring both wideband ADCs and DACs to process signal(s) that have wide instantaneous bandwidth. The device features eight transmit and eight receive lanes that support 24.75 Gbps/lane JESD204C or 15.5 Gbps/lane JESD204B standards. The device also has an on-chip clock multiplier, and a digital signal processing (DSP) capability targeted at either wideband or multiband direct to RF applications. The DSP datapaths can be bypassed to allow a direct connection between the converter cores and the JESD204 data transceiver port. The device also features low latency loopback and frequency hopping modes targeted at phase array radar system and electronic warfare applications. Two models for the AD9081 are offered. The 4D4AC model supports the full instantaneous channel bandwidth, whereas the 4D4AB model supports a maximum instantaneous bandwidth of 600 MHz per channel by automatically configuring the DSP to limit the instantaneous bandwidth at startup.APPLICATIONS Wireless communications infrastructure Microwave point-to-point, E-band and 5G mmWave Broadband communications systems DOCSIS 3.1 and 4.0 CMTS Phased array radar and electronic warfare Electronic test and measurement systems

The AD9094 is an 8-bit, 1 GSPS, quad analog-to-digital converter (ADC). The device has an on-chip buffer and a sample-and-hold circuit designed for low power, small size, and ease of use. The device is designed to sample wide bandwidth analog signals up to 1.4 GHz. The AD9094 is optimized for wide input bandwidth, a high sampling rate, high works linearity, and low power in a small package. The quad-ADC cores feature multistage, differential pipelined architecture with integrated output error correction logic. Each ADC features wide bandwidth inputs that support a variety of user-selectable input ranges. An integrated voltage reference facilitates design considerations. The analog inputs and clock signals are differential inputs. Users can configure each pair of intermediate frequency (IF) receiver outputs onto either one or two lanes of JESD204B Subclass 1 or Subclass 0, high speed, serialized outputs, depending on the sample rate and the acceptable lane rate of the receiving logic device. Multiple device synchronization is supported through the SYSREF?, SYNCINB?AB, and SYNCINB?CD input pins. The AD9094 has flexible power-down options that allow significant power savings when desired. To program the power down options, use the 1.8 V capable, serial port interface (SPI). The AD9094 is available in a Pb-free, 72-lead, lead frame chip scale package (LFCSP) and is specified over a junction temperature range of ?40?C to +105?C. This product may be protected by one or more U.S. or international patents. Note that throughout the data sheet, multifunction pins, such as PDWN/STBY, are referred to either by the entire pin name or by a single function of the pin, for example, PDWN, when only that function is relevant. PRODUCT HIGHLIGHTS Low power consumption per channel. JESD204B lane rate support up to 15 Gbps. Wide, full power bandwidth supports IF sampling of signals up to 1.4 GHz. Buffered inputs ease filter design and implementation. Four integrated wideband decimation filters and numerically controlled oscillator (NCO) blocks supporting multiband receivers. Programmable fast overrange detection. On-chip temperature diode for system thermal management.APPLICATIONSLaser imaging, detection, and ranging (LIDAR)CommunicationsDigital oscilloscope (DSO)Ultrawideband satellite receiversInstrumentation