The ADF7021-V is a high performance, low power, narrow-band RF transceiver based on the ADF7021-N. The architecture of the ADF7021-V transceiver is similar to that of the ADF7021-N except that an external VCO is used by the on-chip RF synthesizer for applications that require improved phase noise performance.The ADF7021-V is designed to operate in both the license-free ISM bands and in the licensed bands from 80 MHz to 960 MHz.To minimize RF feedthrough and spurious emissions, the external VCO operates at 2? or 4? the desired RF frequency; the ADF7021-V supports a maximum VCO frequency operation of 1920 MHz. The 4? VCO operation is programmable by enabling an additional on-chip divide-by-2 outside the RF synthesizer loop and offers improved phase noise performance.As with the ADF7021-N receiver, the IF filter bandwidths of 9 kHz, 13.5 kHz, and 18.5 kHz are supported, making the ADF7021-V ideally suited to worldwide narrow-band telemetry applications.The part has both Gaussian and raised cosine transmit data filtering options to improve spectral efficiency for narrow-band applications. It is suitable for circuit applications targeted at the following: European ETSI EN 300 220 North American FCC Part 15, Part 90, and Part 95 Japanese ARIB STD-T67 Korean short-range device regulations Chinese short-range device regulationsA complete transceiver can be built using a small number of discrete external components, making the ADF7021-V very suitable for area-sensitive, high performance driven applications.See data sheet for more information.APPLICATIONS Narrow-band, short range device (SRD) standards ETSI EN 300 220 FCC Part 90 (meets Emission Mask D requirements) FCC Part 95 ARIB STD-T67 Wireless Metering Narrow-band wireless telemetry

The ADF7024 is an ultralow power, integrated transceiver for use in the license-free ISM bands at 433 MHz, 868 MHz, and 915 MHz. Its ease of use and high performance make it suitable for a wide variety of wireless applications. The ADF7024 is suitable for operation under the European ETSI EN 300-220 regulation, the North American FCC Part 15 regulation, and other similar regulatory standards.The ADF7024 can operate under a number of predefined radio profiles. For each radio profile, optimized register settings are provided for the ADF7024 radio. This ensures that the RF communication layer works seamlessly, allowing the user to concentrate on the protocol and system level design and prototyping. The radio profiles cover common data rate and modulation options. There are six radio profiles in total, as shown in Table 1.The ADF7024 operates with a power supply range of 2.2 V to 3.6 V and has very low power consumption in both Tx and Rx modes, enabling long lifetimes in battery-operated systems while maintaining excellent RF performance.The low IF receiver minimizes power consumption and provides excellent sensitivity. The receiver is exceptionally linear and, therefore, is very resilient to the presence of interferers in spectrally noisy environments. The highly efficient transmitter has programmable output power up to 13.5 dBm and automatic power amplifier (PA) ramping to meet transient spurious specifications. The RF synthesizer comprises a voltage controlled oscillator (VCO), a low noise fractional-N phase-locked loop (PLL) and a loop filter, all of which are fully integrated and automatically calibrated. This agile frequency synthesizer facilitates the implementation of frequency-hopping spread spectrum (FHSS) systems.The smart wake mode (SWM) allows the ADF7024 to wake up autonomously from sleep using the internal wake-up timer without intervention from the host processor. This functionality allows carrier sense, packet sniffing, and packet reception while the host processor is in sleep, thereby reducing overall system current consumption.The ADF7024 eases the processing burden of the host processor by integrating the lower layers of a typical communication protocol stack. The host processor can configure the ADF7024 using a simple command-based protocol over a standard 4-wire SPI interface. A single-byte command transitions the radio between states or performs a radio function.A complete wireless solution can be built using a small number of external discrete components and a host processor (typically a microcontroller).For more information, see the ADF7024 Hardware Reference Manual, UG-698, which is only available as part of the ADF7024 design resource package.APPLICATIONS Wireless sensor networks (WSNs) Home and building automation Asset tracking Process and building control Industrial control Internet of Things (IoT)

The ADF7024 is an ultralow power, integrated transceiver for use in the license-free ISM bands at 433 MHz, 868 MHz, and 915 MHz. Its ease of use and high performance make it suitable for a wide variety of wireless applications. The ADF7024 is suitable for operation under the European ETSI EN 300-220 regulation, the North American FCC Part 15 regulation, and other similar regulatory standards.The ADF7024 can operate under a number of predefined radio profiles. For each radio profile, optimized register settings are provided for the ADF7024 radio. This ensures that the RF communication layer works seamlessly, allowing the user to concentrate on the protocol and system level design and prototyping. The radio profiles cover common data rate and modulation options. There are six radio profiles in total, as shown in Table 1.The ADF7024 operates with a power supply range of 2.2 V to 3.6 V and has very low power consumption in both Tx and Rx modes, enabling long lifetimes in battery-operated systems while maintaining excellent RF performance.The low IF receiver minimizes power consumption and provides excellent sensitivity. The receiver is exceptionally linear and, therefore, is very resilient to the presence of interferers in spectrally noisy environments. The highly efficient transmitter has programmable output power up to 13.5 dBm and automatic power amplifier (PA) ramping to meet transient spurious specifications. The RF synthesizer comprises a voltage controlled oscillator (VCO), a low noise fractional-N phase-locked loop (PLL) and a loop filter, all of which are fully integrated and automatically calibrated. This agile frequency synthesizer facilitates the implementation of frequency-hopping spread spectrum (FHSS) systems.The smart wake mode (SWM) allows the ADF7024 to wake up autonomously from sleep using the internal wake-up timer without intervention from the host processor. This functionality allows carrier sense, packet sniffing, and packet reception while the host processor is in sleep, thereby reducing overall system current consumption.The ADF7024 eases the processing burden of the host processor by integrating the lower layers of a typical communication protocol stack. The host processor can configure the ADF7024 using a simple command-based protocol over a standard 4-wire SPI interface. A single-byte command transitions the radio between states or performs a radio function.A complete wireless solution can be built using a small number of external discrete components and a host processor (typically a microcontroller).For more information, see the ADF7024 Hardware Reference Manual, UG-698, which is only available as part of the ADF7024 design resource package.APPLICATIONS Wireless sensor networks (WSNs) Home and building automation Asset tracking Process and building control Industrial control Internet of Things (IoT)

The ADG1634L is a monolithic industrial CMOS (iCMOS?) analog switch comprising four independently selectable single-pole, double-throw (SPDT) switches, respectively.All channels exhibit break-before-make switching action that prevents momentary shorting when switching channels. An EN input on the ADG1634L is used to enable or disable the device. When disabled, all channels are switched off. The switch is enabled with a Logic 1 EN input, while the INx input defines the state of the SPDT switch (see Table 12 in the data sheet).The ultralow on resistance and on-resistance flatness of the switch makes it an ideal solution for data acquisition and gain switching applications, where low distortion is critical. iCMOS construction ensures ultra low power dissipation, making the device ideally suited for portable and battery-powered instruments.An external VL supply provides flexibility for lower logic control. The ADG1634L is both 1.2 V and 1.8 V JEDEC standard compliant.APPLICATIONS Communication systems Medical systems Audio signal routing Video signal routing Automatic test equipment Data acquisition systems Battery-powered systems FPGA and microcontroller systems Sample-and-hold systems Relay replacementsPRODUCT HIGHLIGHTS 8.2 ? maximum on resistance over temperature. Minimum distortion. VL supply for low logic level compatibility. JEDEC standard compliant for both 1.2 V and 1.8 V logic levels. Guaranteed switch off when digital inputs are floating. 24-lead, 4 mm ? 4 mm LFCSP.

The ADG2128?is an analog cross point switch with an array size of 8 ? 12. The switch array is arranged so that there are eight columns by 12 rows, for a total of 96 switch channels. The array is bidirectional, and the rows and columns can be configured as either inputs or outputs. Each of the 96 switches can be addressed and configured through the I2C compatible interface. Standard, full speed, and high speed (3.4 MHz) I2C interfaces are supported. Any simultaneous switch combination is allowed. An additional feature of the ADG2128 is that switches can be updated simultaneously, using the LDSW command. In addition, a RESET option allows all of the switch channels to be reset/off. At power-on, all switches are in the off condition. The device is packaged in a 32-lead, 5 mm ? 5 mm LFCSP_VQ.APPLICATIONS AV switching in TV Automotive infotainment AV receivers CCTV Ultrasound applications KVM switching Telecom applications Test equipment/instrumentation PBX systems

The ADG772 is a low voltage CMOS device that contains two independently selectable single-pole, double throw (SPDT) switches. It is designed as a general-purpose switch and can be used for routing both USB 1.1 and USB 2.0 signals.This device offers a data rate of 1260 Mbps, making the part suitable for high frequency data switching. Each switch conducts equally well in both directions when on and has an input signal range that extends to the supplies. The ADG772 exhibits break-before-make switching action.The ADG772 is available in a 12-lead LFCSP and a 10-lead mini LFCSP. These packages make the ADG772 the ideal solution for space-constrained applications.Product Highlights 1.6 mm ? 1.3 mm mini LFCSP package. USB 1.1 (12 Mbps) and USB 2.0 (480 Mbps) compliant. Single 2.7 V to 3.6 V operation. 1.8 V logic compatible. RoHS compliant. Applications USB 2.0 signal switching circuits Cellular phones PDAs MP3 players Battery-powered systems Headphone switching Audio and video signal routing Communications systems

The AD9988 is a highly integrated device with four 16-bit, 12 GSPS maximum sample rate, RF digital-to-analog converter (DAC) cores, and four 12-bit, 4 GSPS rate, RF analog-to-digital converter (ADC) cores. The device supports four transmitter channels and four receiver channels with a 4T4R configuration. This product is well suited for four-antenna TDD transmitter applications, where the receiver path can be shared between receiver and observation modes. The GPIO pins can be configured and toggled to support different user modes, while phase coherency is maintained. The maximum radio channel bandwidth supported is 1.2 GHz in a 4T4R configuration and a sample resolution of 16 bits. The AD9988 features a 16-lane 24.75 Gbps JESD204C or 15.5 Gbps JESD204B serial data port that allows up to eight lanes per transmit/receive link, an on-chip clock multiplier, and digital signal processing capability targeted at multiband direct to RF radio applications.APPLICATIONSWireless communications infrastructureW-CDMA, LTE, LTE-A, massive multiple input multiple output (MIMO)Point to point microwave, E-band, and 5G mmWaveBroadband communications systemsDOCSIS 3.0+ cable modem termination system (CMTS)Communication test and measurement systems

The ADA4807-1 (single), ADA4807-2 (dual), and ADA4807-4 (quad) are low noise, rail-to-rail input and output, voltage feedback amplifiers. These amplifiers combine low power, low noise, high speed, and dc precision to provide an attractive solution for a wide range of applications from high resolution data acquisition instrumentation to high performance battery-powered and high component density systems where power consumption is of key importance.With only 1.0 mA of supply current per amplifier, the ADA4807-1/ADA4807-2/ADA4807-4 feature the lowest input voltage noise?among high speed, rail-to-rail input/output amplifiers in the industry and offer a wide bandwidth, high slew rate, fast settling time, and excellent distortion performance. Additionally, these amplifiers offer very low input offset voltage and drift performance, making them ideal for driving multiplexed and high throughput?precision 16-/18-bit successive approximation registers (SARs) and 24-bit ?-? ADCs.These amplifiers are fully specified at +3 V, +5 V, and ?5 V supplies and can operate over the industrial ?40?C to +125?C?temperature range.The ADA4807-1 is available in 6-lead SOT-23 and space-saving 6-lead SC70 packages. The ADA4807-2 is available in an 8-lead?MSOP and a compact, 3 mm ? 3 mm, 10-lead LFCSP. The ADA4807-4 is available in a 14-lead TSSOP package.Applications High resolution analog-to-digital converter (ADC) drivers Portable and battery-powered instruments and systems? High component density data acquisition systems Audio signal conditioning Active filters

The ADA4850-1/ADA4850-2 are low price, high speed, voltagefeedbacks rail-to-rail output op amps with ultralow power-down.Despite their low price, the ADA4850-1/ADA4850-2 provideexcellent overall performance and versatility. The 175 MHz,?3 dB bandwidth and 220 V/?s slew rate make these amplifierswell-suited for many general-purpose, high speed applications.The ADA4850-1/ADA4850-2 are designed to operate at supplyvoltages as low as 2.7 V and up to 6 V at 2.4 mA of supplycurrent per amplifier. In power-down mode, the supply currentis less than 150 nA, ideal for battery-powered applications.The ADA4850-1/ADA4850-2 family provides users with a truesingle-supply capability, allowing input signals to extend200 mV below the negative rail and to within 2.2 V of thepositive rail. The output of the amplifier can swing within80 mV of either supply rail.With its combination of low price, excellent differential gain(0.12%), differential phase (0.09?), and 0.1 dB flatness out to14 MHz, these amplifiers are ideal for video applications. The ADA4850-1/ADA4850-2 are designed to work in theextended temperature range of ?40?C to +125?C. Applications Portable multimedia players Video cameras Digital still cameras Consumer video Clock buffers

The ADA4853-1/ADA4853-2/ADA4853-3 are low power, low cost, high speed, rail-to-rail output op amps with ultralow power disables that are ideal for portable consumer electronics. Despite their low price, the ADA4853-1/ADA4853-2/ADA4853-3 provide excellent overall performance and versatility. The 100 MHz, ?3 dB bandwidth, and 120 V/?s slew rate make these amplifiers well-suited for many general-purpose, high speed applications.The ADA4853-1/ADA4853-2/ADA4853-3 voltage feedback op amps are designed to operate at supply voltages as low as 2.65 V and up to 5 V using only 1.4 mA of supply current per amplifier. To further reduce power consumption, the amplifiers are equipped with a power-down mode that lowers the supply current to less than 1.5 ?A maximum, making them ideal in battery-powered applications.The ADA4853-1/ADA4853-2/ADA4853-3 provide users with a true single-supply capability, allowing input signals to extend 200 mV below the negative rail and to within 1.2 V of the positive rail. On the output, the amplifiers can swing within 200 mV of either supply rail.With their combination of low price, excellent differential gain (0.2%), differential phase (0.10?), and 0.5 dB flatness out to 22 MHz, these amplifiers are ideal for video applications.The ADA4853-1 is available in a 6-lead SC70, the ADA4853-2 is available in a 16-lead LFCSP_WQ, and the ADA4853-3 is available in both a 16-lead LFCSP_WQ and a 14-lead TSSOP. The ADA4853-1 temperature range is ?40?C to +85?C while the ADA4853-2/ADA4853-3 temperature range is ?40?C to +105?C.Applications Automotive infotainment systems Automotive safety systems Portable multimedia players Video cameras Digital still cameras Consumer video Clock buffer