The ADAQ23878 is a precision, high speed, ?Module? data acquisition solution that reduces the development cycle of a precision measurement systems by transferring the design burden of component selection, optimization, and layout from the designer to the device.Using System-in-Package (SIP) technology, the ADAQ23878 reduces end system component count by combining multiple common signal processing and conditioning blocks in a single device, including a low noise, fully differential ADC driver (FDA), a stable reference buffer, and a high speed, 18-bit, 15 MSPS successive approximation register (SAR) ADC.The ADAQ23878 also incorporates the critical passive components with superior matching and drift characteristics using Analog Devices, Inc., iPassive? technology to minimize temperature dependent error sources and to offer optimized performance. The fast settling of the ADC driver stage and no latency of the SAR ADC provide a unique solution for high channel count multiplexed signal chain architectures and control loop applications.The small footprint, 9 mm ? 9 mm BGA package enables smaller form factor instruments without sacrificing performance. The system integration solves many design challenges while the device still provides the flexibility of a configurable ADC driver feedback loop to allow gain or attenuation adjustments, as well as fully differential or single-ended to differential input. A single 5 V supply operation is possible while achieving optimum performance from the device.The ADAQ23878 features a serial low voltage differential signaling (LVDS) digital interface with one-lane or two-lane output modes, allowing the user to optimize the interface data rate for each application. The specified operation of the ADAQ23878 is from ?40?C to +85?C.APPLICATIONS Automatic test equipment Data acquisition Hardware in the Loop (HiL) Power analyzers Non-destructive test (acoustic emissions) Mass spectrometry Travelling wave fault location Medical imaging and instruments

The ADAQ7980/ADAQ7988 are 16-bit analog-to-digital converter(ADC) ?Module? data acquisition systems that integrate four common signal processing and conditioning blocks into a system in package (SiP) design that supports a variety of applications. These devices contain the most critical passive components,eliminating many of the design challenges associated with traditional signal chains that use successive approximation register (SAR) ADCs. These passive components are crucial to achieving the specified device performance.The ADAQ7980/ADAQ7988 contain a high accuracy, low power, 16-bit SAR ADC, a low power, high bandwidth, high inputimpedance ADC driver, a low power, stable reference buffer,and an efficient power management block. Housed within a tiny, 5 mm ? 4 mm LGA package, these products simplify the design process for data acquisition systems. The level of system integrationof the ADAQ7980/ADAQ7988 solves many design challenges, while the devices still provide the flexibility of a configurableADC driver feedback loop to allow gain and/or common-mode adjustments. A set of four device supplies provides optimal system performance; however, single-supply operation is possible with minimal impact on device operating specifications.The ADAQ7980/ADAQ7988 integrate within a compact, integrated circuit (IC)-like form factor key componentscommonly used in data acquisition signal chain designs. The?Module family transfers the design burden of componentselection, optimization, and layout from designer to device,shortening overall design time, system troubleshooting, and ultimately improving time to market.The serial peripheral interface (SPI)-compatible serial interfacefeatures the ability to daisy-chain multiple devices on a single, 3-wire bus and provides an optional busy indicator. The userinterface is compatible with 1.8 V, 2.5 V, 3 V, or 5 V logic.Specified operation of these devices is from ?55?C to +125?C.Applications Automated test equipment (ATE) Battery powered instrumentation Communications Data acquisition Process control Medical instruments

The ADAR7251 is a 16-bit, 4-channel, simultaneous sampling analog-to-digital converter (ADC) designed especially for applications such as automotive LSR-FMCW or FSK-FMCW radar systems. Each of the four channels contains a low noise amplifier (LNA), a programmable gain amplifier (PGA), an equalizer, a multibit ?-? ADC, and a decimation filter.The front-end circuitry is designed to allow direct connection to an MMIC output with few external passive components. The ADAR7251 eliminates the need for a high order antialiasing filter, driver op amps, and external bipolar supplies. The ADAR7251 also offers precise channel-to-channel drift matching.The ADAR7251 features an on-chip phase-locked loop (PLL) that allows a range of clock frequencies for flexibility in the system. The CONV_START input and DATA_READY output signals synchronize the ADC with an external ramp for applications such as FSK-FMCW radar.The ADAR7251 supports serial and parallel interfaces at programmable sample rates from 300 kSPS to 1.8 MSPS, as well as easy connections to digital signal processors (DSPs) and microcontroller units (MCUs) in the system.APPLICATIONS Automotive LSR systems Data acquisition systems

The ADATE209 is a dual pin driver designed for testing DDR2, DDR3, and DDR4. It can also be used for high speed SoC applications, such as testing PCI Express 1.0 and HDMI?. The device is a three-level driver capable of high fidelity swings from 200 mV to 4 V over a ?1 V to +3.5 V range. It has rise/fall times (20% to 80%) under 120 ps for a 2 V programmed swing and 150 ps for a 3 V programmed swing, and is capable of supporting data rates of 4.4 Gbps and 3.2 Gbps, respectively.The device is capable of high speed transitions into and out of termination mode. It also contains peaking/pre-emphasis circuitry.The ADATE209 is available in an 8 mm ? 8 mm, 49-ball CSP_BGA.APPLICATIONS Automatic test equipment Semiconductor test systems Board test systems Instrumentation and characterization equipment High speed memory testing (DDR2/DDR3/DDR4) HDMI testing

The ADAU1401A is a complete, single-chip audio system with 28-/56-bit audio DSP, ADCs, DACs, and microcontroller-like control interfaces. Signal processing includes equalization, cross-over, bass enhancement, multiband dynamics processing, delay compensation, speaker compensation, and stereo image widening. This processing can be used to compensate for real-world limitations of speakers, amplifiers, and listening environments, providing dramatic improvements in perceived audio quality.The signal processing of the ADAU1401A is comparable to that found in high end studio equipment. Most processing is done in full 56-bit, double-precision mode, resulting in very good low level signal performance. The ADAU1401A is a fully programmable DSP. The easy to use SigmaStudio? software allows the user to graphically configure a custom signal processing flow using blocks such as biquad filters, dynamics processors, level controls, and GPIO interface controls.The ADAU1401A programs can be loaded on power-up either from a serial EEPROM through its own self-boot mechanism or from an external microcontroller. On power-down, the current state of the parameters can be written back to the EEPROM from the ADAU1401A to be recalled the next time the program is run.Two ?-? ADCs and four ?-? DACs provide a 98.5 dB analog input to analog output dynamic. Each ADC has a THD + N of ?83 dB, and each DAC has a THD + N of ?90 dB. Digital input and output ports allow a glueless connection to additional ADCs and DACs. The ADAU1401A communicates through an I2C? bus or a 4-wire SPI port.APPLICATIONS Multimedia speaker systems MP3 player speaker docks Automotive head units Minicomponent stereos Digital televisions Studio monitors Speaker crossovers Musical instrument effects processors In-seat sound systems (aircraft/motor coaches)

The ADAU1472 is a high quality SigmaDSP? digital audio?processor with a large internal memory, enabling efficient audio?source separation, far field voice capture, speech processing, deep?learning, and advanced audio signal processing. The processor combines the highly optimized Cadence? Tensilica? HiFi? 4?audio/voice processor with custom Analog Devices, Inc.,?instruction extensions for math acceleration, and a flexible input and output architecture. The?HiFi 4 processor supports four 32-bit ? 32-bit multiplier?accumulators (MACs) per cycle with 72-bit accumulators, dual 64-bit memory load, and a native Institute of Electrical and?Electronics Engineers (IEEE) single precision, floating-point multiplier.The ADAU1472 processor offers performance up to 270.336 MHz,?supports low latency, sample by sample audio processing, and?block by block processing paradigms in parallel. The integer?phase-locked loop (PLL) and flexible clock generator hardware?can generate up to 15 audio sample rates simultaneously (8 kHz?to 192 kHz). These clock generators, along with the on-board?asynchronous sample rate converters (ASRCs) and flexible?hardware audio routing matrix, greatly simplify the design of?complex audio systems.The HiFi 4 digital signal processor (DSP) core has 480 kB of L1?memory running at the DSP core clock rate, which consists of?256 kB data random access memory (RAM), 64 kB instruction?RAM, 128 kB data cache, and 32 kB instruction cache, along with?2 MB of L2 system static random access memory (SRAM)?running at one half of the DSP core clock rate. The processor?also supports up to 2 GB of external flash memory to enable the?storage of large data tables and self boot code.Dual on-chip power domains allow low power operation,?including the capability of routing audio through a flexible audio?routing matrix with IOVDD as the only active supply.?The configurable voice detection hardware can detect human?speech onset while operating in a low power state and can?generate both internal DSP and external wake-up signals.The ADAU1472 interfaces with a wide range of analog-to-digital?converters (ADCs), digital-to-analog converters (DACs), digital?audio devices, amplifiers, and control circuitry due to its highly?configurable serial ports, Sony/Philips digital interface?format (S/PDIF) interfaces, and multipurpose input/output?pins. The device can also directly interface with up to 14 pulse?density modulated (PDM) output microphones due to?integrated decimation filters specifically designed for that?purpose. The PDM outputs with integrated interpolation filters?provide direct connectivity to PDM input Class D amplifiers.The processor has two serial peripheral interface (SPI) bus master?control ports that allow the device to communicate with multiple?SPI-compatible devices including support for single, dual, and?quad input/output operation. In addition, the SPI flash port?allows direct memory mapped read access with minimal central?processing unit (CPU) overhead and standalone self boot?operation.The combined high performance DSP core, large RAM, and?small footprint make the ADAU1472 an ideal replacement for?large, general-purpose DSPs that consume more power for the?same processing load.Applications Far field voice interface devices Audio source separation Embedded deep learning for audio Commercial and professional audio processing

The ADG4612 & ADG4613?contain four independent single-pole/single-throw (SPST) switches. The ADG4612 switches areturned on with Logic 1 on the appropriate control input. TheADG4613 has two switches with digital control logic similar tothat of the ADG4612; the logic is inverted on the other twoswitches. Each switch conducts equally well in both directionswhen on and has an input signal range that extends to thesupplies. The ADG4613 exhibits break-before-make switchingaction for use in multiplexer applications.When no power supplies are present the switch remains in theOFF condition and the switch inputs are high impedanceinputs. This ensures that no current flows that may damage theswitch. This is very useful in application where analog signalsmay be present at the switch inputs before power or where theuser has no control over the Power Supply Sequence.In the off condition, signal levels up to 16V are blocked. Also, ifthe analog input signal levels exceed VDD by VT then the switchwill turn off.The ultralow on resistance of these switches make them idealsolutions for data acquisition and gain switching applicationswhere low on resistance and distortion is critical. The onresistance profile is very flat over the full analog input rangeensuring excellent linearity and low distortion when switchingaudio signals.APPLICATIONS Hot swap applications Data acquisition systems Battery-powered systems Automatic test equipment Communication systems Relay ReplacementPRODUCT HIGHLIGHTS Power-Off Protection On Both S and D Pins. PSS Robustness. Overvoltage Protection up to 16 V. 5.2 ? On Resistance. 16-Lead TSSOP and 3 mm ? 3 mm LFCSP Packages.

The ADG5248F and ADG5249F are 8:1 and dual 4:1 analog multiplexers. The ADG5248F switches one of eight inputs to a common output and the ADG5249F switches one of four differential inputs to a common differential output. Each channel conducts equally well in both directions when on, and each channel has an input signal range that extends to the supplies. The primary supply voltages define the on-resistance profile, whereas the secondary supply voltages define the voltage level at which the overvoltage protection engages.When no power supplies are present, the channel remains in the off condition, and the switch inputs are high impedance. Under normal operating conditions, if the analog input signal levels on any Sx pin exceed positive fault voltage (POSFV) or negative fault voltage (NEGFV) by a threshold voltage (VT), the channel turns off and that Sx pin becomes high impedance. If the switch is selected to be on, then the drain pin is pulled to the secondary supply voltage that was exceeded. Input signal levels up to +55 V or ?55 V relative to ground are blocked, in both the powered and unpowered condition.The low capacitance and charge injection of these switches make them ideal solutions for data acquisition and sample-and-hold applications, where low glitch switching and fast settling times are required.?Note that, throughout this data sheet, multifunction pins, such as A0/F2, are referred to either by the entire pin name or by a single function of the pin, for example, A0, when only that function is relevant.?Product Highlights Source pins are protected against voltages greater than the secondary supply rails, up to ?55 V and +55 V. Source pins are protected against voltages between ?55 V and +55 V in an unpowered state. Overvoltage detection with digital output indicates operating state of switches. Trench isolation guards against latch-up. Optimized for low charge injection and on-capacitance. The ADG5248F/ADG5249F can be operated from a dual?supply of ?5 V to ?22 V or a single power supply of 8 V to 44 V.Applications Analog input/output modules Process control/distributed control systems Data acquisition Instrumentation Avionics Automatic test equipment Communication systems Relay replacement

The ADG5412F and ADG5413F contain four independently controlled single-pole/single-throw (SPST) switches. The ADG5412F has four switches that turn on with Logic 1 inputs. The ADG5413F has two switches with that turn on and two switches that turn off with Logic 1 inputs. Each switch conducts equally well in both directions when on, and each switch has an input signal range that extends to the supplies. The digital inputs are compatible with 3 V logic inputs over the full operating supply range.When no power supplies are present, the switch remains in the off condition, and the switch inputs are high impedance. Under normal operating conditions, if the analog input signal levels on any Sx pin exceed VDD or VSS by a threshold voltage, VT, then the switch turns off. Input signal levels up to +55 V or ?55 V relative to ground are blocked, in both the powered and unpowered condition.The low on resistance of these switches, combined with on-resistance flatness over a significant portion of the signal range make them an ideal solution for data acquisition and gain switching applications where excellent linearity and low distortion are critical.Product Highlights Source pins are protected against voltages greater than the supply rails, up to ?55 V and +55 V. Source pins are protected against voltages between ?55 V and +55 V, in an unpowered state. Overvoltage detection with digital output indicates operating state of switches. Trench isolation guards against latch-up. Optimized for low on resistance and on-resistance flatness. The ADG5412F/ADG5413F can be operated from a dual?supply of ?5 V up to ?22 V or a single power supply of 8 V up to 44 V.Applications Analog input/output modules Process control/distributed control systems Data acquisition Instrumentation Avionics Automatic test equipment Communication systems Relay replacement

The ADG918/ADG919 are wideband switches using a CMOSprocess to provide high isolation and low insertion loss to1 GHz. The ADG918 is an absorptive (matched) switch having50 ? terminated shunt legs, whereas the ADG919 is a reflectiveswitch. These devices are designed such that the isolation ishigh over the dc to 1 GHz frequency range. They have on-boardCMOS control logic, thus eliminating the need for externalcontrolling circuitry. The control inputs are both CMOS andLVTTL compatible. The low power consumption of theseCMOS devices makes them ideally suited to wireless andgeneral-purpose high frequency switching applications.Product Highlights ?43 dB off isolation at 1 GHz. 0.8 dB insertion loss at 1 GHz. Tiny 8-lead MSOP/LFCSP.Applications Wireless communications General-purpose RF switching Dual-band applications High speed filter selection Digital transceiver front end switch IF switching Tuner modules Antenna diversity switching