The ADAQ23875 is a precision, high speed, ?Module? data acquisition solution that reduces the development cycle of a precision measurement systems by transferring the design burden of component selection, optimization, and layout from the designer to the device.Using system-in-package (SIP) technology, the ADAQ23875 reduces end system component count by combining multiple common signal processing and conditioning blocks in a single device, solving many design challenges. These blocks include a low noise, fully differential analog-to-digital converter (ADC) driver (FDA), a stable reference buffer, and a high speed, 16-bit, 15 MSPS successive approximation register (SAR) ADC.Using Analog Devices, Inc., iPassives? technology, the ADAQ23875 also incorporates crucial passive components with superior matching and drift characteristics to minimize temperature dependent error sources and to offer optimized performance (see Figure 1). The fast settling of the ADC driver stage, with fully differential or single-ended to differential input and no latency of the SAR ADC, provides a unique solution for high channel count multiplexed signal chain architectures and control loop applications.The small footprint, 9 mm ? 9 mm CSP_BGA package enables smaller form factor instruments without sacrificing performance. Single, 5 V supply operation is possible while achieving optimum performance from the device. The ADAQ23875 features a serial low voltage differential signaling (LVDS) digital interface with one-lane or two-lane output modes, allowing the user to optimize the interface data rate for each application. The specified operation of the ?Module is from ?40?C to +85?C.APPLICATIONSATEData acquisitionHardware in the Loop (HiL)Power analyzersNondestructive test (acoustic emissions)Mass spectrometryTravelling wave fault locationMedical imaging and instrumentsUltrasonic flow meters

The ADAS3022 is a complete 16-bit, 1 MSPS, successive approximation?based analog-to-digital data acquisition system, which is manufactured on Analog Devices, Inc., proprietary iCMOS? high voltage industrial process technology. The device integrates an 8-channel, low leakage multiplexer; a high impedance programmable gain instrumentation amplifier (PGIA) stage with high common-mode rejection; a precision, low drift 4.096 V reference and buffer; and a 16-bit charge redistribution analog-to-digital converter (ADC) with successive approximation register (SAR) architecture. The ADAS3022 can resolve eight single-ended inputs or four fully differential inputs up to ?24.576 V when using ?15 V supplies. In addition, the device can accept the commonly used bipolar differential, bipolar single-ended, pseudo bipolar, or pseudo unipolar input signals, as shown in Table 1, thus enabling the use of almost any direct sensor interface.The ADAS3022 simplifies design challenges by eliminating signal buffering, level shifting, amplification/attenuation, common-mode rejection, settling time, and any other analog signal conditioning challenge while allowing a smaller form factor, faster time to market, and lower cost.APPLICATIONS ?Multichannel data acquisition and system monitoring Process control Power line monitoring Automated test equipment Instrumentation

The ADAU1772 is a codec with four inputs and two outputs that incorporates a digital processing engine to perform filtering, level control, signal level monitoring, and mixing. The path from the analog input to the DSP core to the analog output is optimized for low latency and is ideal for noise cancelling headsets. With the addition of just a few passive components, a crystal, and an EEPROM for booting, the ADAU1772 provides a complete headset solution.APPLICATIONS Noise cancelling headsets, headsets, and headphones BlueTooth ANC headsets, headsets, and headphones Personal navigation devices Digital still and video cameras

The ADAU7118 converts four stereo pulse density modulation (PDM) bitstreams into one pulse code modulation (PCM) output stream. The source for the PDM data can be eight microphones or other PDM sources. The PCM audio data is output on a serial audio interface port in either inter-IC serial (I2S) or time domain multiplexed (TDM) format.The ADAU7118 is specified over the commercial temperature range (?40?C to +85?C). The ADAU7118 is available in a 16-lead, 3 mm ? 3 mm, 0.40 mm pitch, lead frame chip scale package (LFCSP).Note that throughout this data sheet, multifunction pins, such as ADDR/CONFIG, are referred to either by the entire pin name or by a single function of the pin, for example, ADDR, when only that function is relevant.Applications Microphone arrays Mobile computing Portable electronics Consumer electronics Professional electronics

The ADcmXL3021 is a complete vibration sensing system that combines high performance vibration sensing (using micro-electromechanical systems (MEMS) accelerometers) with a variety of signal processing functions to simplify the development of smart sensor nodes in condition-based monitoring (CBM) systems. The typical ultralow noise density (26 ?g/?Hz) in the MEMS accelerometers supports excellent resolution. The wide bandwidth (dc to 10 kHz within 3 dB flatness) enables tracking of key vibration signatures on many machine platforms.The signal processing includes high speed data sampling (220 kSPS), 4096 time sample record lengths, filtering, windowing, fast Fourier transform (FFT), user configurable spectral or time statistic alarms, and error flags. The serial peripheral interface (SPI) provides access to a register structure that contains the vibration data and a wide range of user configurable functions.The ADcmXL3021 is available in a 23.7 mm ? 27.0 mm ? 12.4 mm aluminum package with four mounting flanges to support installation with standard machine screws. This package provides consistent mechanical coupling to the core sensors over a broad frequency range. The electrical interface is through a 14-pin connector on a 36 mm flexible cable, which enables a wide range of location and orientation options for system mating connectors.The ADcmXL3021 requires only a single, 3.3 V power supply and supports an operating temperature range of ?40?C to +105?C.Applications Vibration analysis CBM systems Machine health Instrumentation and diagnostics Safety shutoff sensing

The ADCMP580/ADCMP581/ADCMP582 are ultrafast voltagecomparators fabricated on the Analog Devices, Inc. proprietaryXFCB3 Silicon Germanium (SiGe) bipolar process. TheADCMP580 features CML output drivers, the ADCMP581features reduced swing ECL (negative ECL) output drivers, andthe ADCMP582 features reduced swing PECL (positive ECL)output drivers.All three comparators offer 180 ps propagation delay and 100 psminimum pulse width for 10 Gbps operation with 200 fs randomjitter (RJ). Overdrive and slew rate dispersion are typically lessthan 15 ps.The ?5 V power supplies enable a wide ?2 V to +3 V inputrange with logic levels referenced to the CML/NECL/PECLoutputs. The inputs have 50 ? on-chip termination resistorswith the optional capability to be left open (on an individualpin basis) for applications requiring high impedance input. The CML output stage is designed to directly drive 400 mV into50 ? transmission lines terminated to ground. The NECL outputstages are designed to directly drive 400 mV into 50 ? terminatedto ?2 V. The PECL output stages are designed to directly drive400 mV into 50 ? terminated to VCCO ? 2 V. High speed latchand programmable hysteresis are also provided. The differentiallatch input controls are also 50 ? terminated to an independentVTT pin to interface to either CML or ECL or to PECL logic.The ADCMP580/ADCMP581/ADCMP582 are available in a16-lead LFCSP.Applications Automatic test equipment (ATE) High speed instrumentation Pulse spectroscopy Medical imaging and diagnostics High speed line receivers Threshold detection Peak and zero-crossing detectors High speed trigger circuitry Clock and data signal restoration

The ADE7753 features proprietary ADCs and DSP for highaccuracy over large variations in environmental conditions andtime. The ADE7753 incorporates two second-order 16-bit ?-?ADCs, a digital integrator (on CH1), reference circuitry,temperature sensor, and all the signal processing required toperform active, reactive, and apparent energy measurements,line-voltage period measurement, and rms calculation on thevoltage and current. The selectable on-chip digital integratorprovides direct interface to di/dt current sensors such asRogowski coils, eliminating the need for an external analogintegrator and resulting in excellent long-term stability and precisephase matching between the current and voltage channels.The ADE7753 provides a serial interface to read data, and apulse output frequency (CF), which is proportional to the activepower. Various system calibration features, i.e., channel offsetcorrection, phase calibration, and power calibration, ensurehigh accuracy. The part also detects short duration low or highvoltage variations.The positive-only accumulation mode gives the option toaccumulate energy only when positive power is detected. Aninternal no-load threshold ensures that the part does not exhibitany creep when there is no load. The zero-crossing output (ZX)produces a pulse that is synchronized to the zero-crossing pointof the line voltage. This signal is used internally in the line cycleactive and apparent energy accumulation modes, which enables faster calibration.The interrupt status register indicates the nature of the interrupt,and the interrupt enable register controls which event producesan output on the IRQ pin, an open-drain, active low logic output.The ADE7753 is available in a 20-lead SSOP package.NOTE: For polyphase system designs, the ADE7758 is recommended.

The ADE7854A?/?ADE7858A?/?ADE7868A?/?ADE7878A are high accuracy, 3-phase electrical energy measurement ICs with serial interfaces and three flexible pulse outputs. The devices incorporate second-order ?-? analog-to-digital converters (ADCs), a digital integrator, reference circuitry, and all signal processing required to perform total (fundamental and harmonic) active, reactive (ADE7858A, ADE7868A, and ADE7878A), and apparent energy measurement and rms calculations.The ADE7878A can also perform fundamental-only active and reactive energy measurement and rms calculations. A fixed function digital signal processor (DSP) executes the signal processing. The DSP program is stored in the internal ROM memory.The ADE7854A / ADE7858A / ADE7868A / ADE7878A can measure active, reactive, and apparent energy in various 3-phase configurations, such as wye or delta services, with both three and four wires. Aside from regular rms measurements, which are updated every 8 kHz, these devices measure low ripple rms values, which are averaged internally and updated every 1.024 sec. The devices provide system calibration features for each phase, that is, rms offset correction, phase calibration, and gain calibration.The CF1, CF2, and CF3 logic outputs provide a wide selection of power information. All four devices provide total active and apparent powers, as well as the sum of the current rms values; the ADE7858A, ADE7868A, and ADE7878A also provide total reactive powers; the ADE7878A also provides fundamental active and reactive powers.The ADE7854A / ADE7858A / ADE7868A / ADE7878A contain waveform sampling registers that allow access to all ADC outputs. The devices also incorporate power quality measurements, such as short duration low or high voltage detection, short duration high current variation, line voltage period measurement, and angles between phase voltages and currents.Two serial interfaces, serial peripheral interface (SPI) and I2C, can communicate with the devices. A dedicated high speed interface, the high speed data capture (HSDC) port, can be used in conjunction with I2C to provide access to the ADC outputs and real-time power information.The devices have two interrupt request pins, IRQ0 and IRQ1, to indicate that an enabled interrupt event has occurred. For the ADE7868A / ADE7878A, three specially designed low power modes ensure the continuity of energy accumulation when the ADE7868A / ADE7878A are in a tampering situation.

The ADE7880 is high accuracy, 3-phase electrical energy measurement IC with serial interfaces and three flexible pulse outputs. The ADE7880 device incorporates second-order sigma-delta (?-?) analog-to-digital converters (ADCs), a digital integrator, reference circuitry, and all of the signal processing required to perform the total (fundamental and harmonic) active, and apparent energy measurements, rms calculations, as well as fundamental-only active and reactive energy measurements. In addition, the ADE7880 computes the rms of harmonics on the phase and neutral currents and on the phase voltages, together with the active, reactive, and apparent power, and the power factor and harmonic distortion on each harmonic for all phases. Total harmonic distortion plus noise (THD + N) is computed for all currents and voltages. A fixed function digital signal processor (DSP) executes this signal processing. The DSP program is stored in the internal ROM memory.The ADE7880 is suitable for measuring active, reactive, and apparent energy in various 3-phase configurations, such as wye or delta services with both three and four wires. The ADE7880 provides system calibration features for each phase, that is, rms offset correction, phase calibration, and gain calibration. The CF1, CF2, and CF3 logic outputs provide a wide choice of power information: total active powers, apparent powers, or the sum of the current rms values, and fundamental active and reactive powers.The ADE7880 contains waveform sample registers that allow access to all ADC outputs. The devices also incorporate power quality measurements, such as short duration low or high voltage detections, short duration high current variations, line voltage period measurement, and angles between phase voltages and currents. Two serial interfaces, SPI and I2C, can be used to communicate with the ADE7880. A dedicated high speed interface, the high speed data capture (HSDC) port, can be used in conjunction with I2C to provide access to the ADC outputs and real-time power information. The ADE7880 also has two interrupt request pins, IRQ0 and IRQ1, to indicate that an enabled interrupt event has occurred. Three specially designed low power modes ensure the continuity of energy accumulation when the ADE7880 is in a tampering situation. The ADE7880 is available in the 40-lead LFCSP, Pb-free package, pin-for-pin compatible with ADE7854, ADE7858, ADE7868, and ADE7878?devices.APPLICATIONS Energy metering systems Power quality monitoring Solar inverters Process monitoring Protective devices

The ADE7903 is a nonisolated, 3-channel, ?-? analog-to-digital converter (ADC) for the neutral line of polyphase energymetering applications using shunt current sensors. The ADE7903 can also be used for single-phase energy meteringand other standalone ADC applications. The ADE7903 features three 24-bit ADCs. The current ADC provides a 67 dBFSsignal-to-noise ratio (SNR) over a 3.3 kHz signal bandwidth, whereas the voltage ADCs provide an SNR of 72 dBFS over thesame bandwidth. One channel is dedicated to measuring the voltage across a shunt when the shunt is used for current sensing.Up to two additional channels are dedicated to measuring voltages, which are usually sensed using resistor dividers.One voltage channel can be used to measure the temperature of the die via an internal sensor. The ADE7903 includes threechannels: one current channel and two voltage channels.Together with the ADE7912?/ ADE7913, the ADE7903 providesa small form factor, 3-phase isolated solution with a neutralmeasurement. The three phases are isolated with ADE7912 /ADE7913 devices, while the neutral line is not isolated with theADE7903. The ADE7903 configuration and status registers are accessedvia a bidirectional SPI serial port for easy interfacing withmicrocontrollers.The ADE7903 can be clocked from a crystal or an externalclock signal. To minimize the system bill of materials, themaster ADE7912 / ADE7913 can drive the clocks of up to threeadditional ADE7912 / ADE7913 or ADE7903 devices.Multiple ADE7912 / ADE7913 and ADE7903 devices can besynchronized to sample at the same moment and providecoherent outputs. The ADE7903 can also be used individuallyas a standalone ADC. The ADE7903 is available in a 20-lead, Pb-free, wide body SOICpackage.APPLICATIONS 3-phase shunt-based polyphase meters with neutral channel measurement Single-phase meters Power quality monitoring Solar inverters Process monitoring Standalone ADCs Protective devices Isolated sensor interfaces Industrial programmable logic controllers (PLCs)