DC1534A-B: Demo Board for the LTC2637-12 Octal 12-Bit I2C VOUT DACs with 10ppm/°C Reference.

DC1554A-B: Demo Board for the LTM2882 Dual Isolated RS232 µModule Transceiver + Power.

Demonstration circuit DC1555C is intended to demonstrate the performance of the LTC4365 and LTC4365-1 Undervoltage, Overvoltage and Reverse Supply Protection Controllers. The LTC4365/LTC4365-1 protect circuits from input voltages that may be too high, too low or negative. It operates by controlling the gates of two back-to-back connected MOSFETs to keep the output in a safe range. The OV and UV protection levels are adjusted by resistive dividers at the OV and UV pins. Asserting the SHDN pin disables the MOSFETs and places the controller in a low-current shutdown state. The FAULT pin is asserted when the Controller is in shutdown mode or when the input voltage is outside of the UV or OV level.

DC1561B: Demo Board for the LTC4278 IEEE 802.3at PD with Synchronous No-Opto Flyback Controller and 12V Auxiliary Support.

The LTC3615/LTC3615-1 are dual 3A synchronous stepdown regulators using a current mode, constant-frequency architecture. The DC supply current is only 130?A (Burst Mode operation at no-load) while maintaining the output voltages, dropping to zero current in shutdown. The 2.25V to 5.5V input supply range makes the parts ideally suited for single Li-Ion applications. 100% duty cycle capability provides low dropout operation, which extends operating time in battery-operated systems.The operating frequency is externally programmable up to 4MHz, allowing the use of small surface mount inductors. 0?, 90?, or 180? (LTC3615) or 140?/180? (LTC3615-1) of phase shift between the two channels can be selected to minimize input current ripple and output voltage ripple in a dual 3A or single 6A output configuration. Programmable slew rate limiting reduces EMI, and external synchronization can be applied up to 4MHz.The internal synchronous switches increase efficiency and eliminate the need for external catch diodes, saving external components and board space.The LTC3615/LTC3615-1 are offered in leadless 24-pin 4mm ? 4mm QFN and thermally enhanced 24-pin eTSSOP packages.Applications Point-of-Load Supplies Distributed Power Supplies Portable Computer Systems DDR Memory Termination Handheld Devices

DC1582B-A: Demo Board for the LTC3108 Ultralow Voltage Step-Up Converter and Power Manager.

DC1584A: Demo Board for the LTC4070 Li-Ion/Polymer Shunt Battery Charger System.

DC1593A-D: Demo Board for LTC2635-12 Quad 12-Bit I2C VOUT DACs with 10ppm/°C Reference.

The LT3799 is an isolated flyback controller with power factor correction specifically designed for driving LEDs. The controller operates using critical conduction mode allowing the use of a small transformer. Using a novel current sensing scheme, the controller is able to deliver a well regulated current to the secondary side without using an opto-coupler. A strong gate driver is included to drive an external high voltage MOSFET. Utilizing an onboard multiplier, the LT3799 typically achieves power factors of 0.97. The FAULT pin provides notification of open and short LED conditions.The LT3799 uses a micropower hysteretic start-up to efficiently operate at offline input voltages, with a third winding to provide power to the part. An internal LDO provides a well regulated supply for the part?s internal circuitry and gate driver. TRIAC Dimmable LED Current Regulation LT3799 YES ?10% LT3799-1 NO ?5% Applications Offline 4W to 100W+ LED Applications High DC VIN LED Applications

Demonstration Circuit 1619A is a 100kHz to 500kHz programmable frequency, high voltage, current mode DC/DC step-down converter featuring the LT3845A. The operating frequency can be synchronized up to 600kHz. This demo board is designed for 12V output at up to 10A (120W) from a 16V to 60V input.