CY8CKIT-149 PSOC 4100S PLUS Prototyping Embedded Evaluation Board

Multi-Sensor High Accuracy Digital Temperature Measurement System with EEPROM Features:Directly Digitizes 2-, 3-, or 4-Wire RTDs, Thermocouples, Thermistors, and DiodesOn-Chip EEPROM (LTC2986-1) Stores Channel Configuration Data and Custom CoefficientsSingle 2.85V to 5.25V Supply10 Flexible Inputs Allow Interchanging SensorsAutomatic Thermocouple Cold Junction CompensationBuilt-In Standard and User-Programmable Coefficients for Thermocouples, RTDs and ThermistorsMeasures Negative Thermocouple VoltagesAutomatic Burn Out, Short-Circuit and Fault DetectionBuffered Inputs Allow External ProtectionSimultaneous 50Hz/60Hz RejectionIncludes 15ppm/°C (Max) ReferenceIncludes Special Protection Modes

Interface Development Tools Si86xx Isolated Linear Reference Design with Si8630BD and Si8630ED in WB SOIC-16 package.

The MAX8566 high-efficiency switching regulator delivers up to 10A load current at output voltages from 0.6V to (0.87 x VIN). The IC operates from 2.3V to 3.6V input supplies, making it ideal for point-of-load applications. The total output-voltage set error is less than ±1% over load, line, and temperature.The MAX8566 operates in pulse-width-modulation (PWM) mode with a 250kHz to 2.4MHz switching frequency range that is programmable by an external resistor. The IC can be synchronized to an external clock in the same frequency range using the SYNC input. The high operating frequency minimizes the size of external components. Using low-RDS(ON) n-channel MOSFETs for both high- and low-side switches maintains high efficiency at both heavy-load and high-switching frequencies.The MAX8566 employs a voltage-mode control architecture with a high-bandwidth (> 10MHz) error amplifier. The voltage-mode control architecture makes switching frequencies greater than 1MHz possible, achieving all-ceramic-capacitor designs to minimize PC board space. The error amplifier works with Type 3 compensation to fully utilize the bandwidth of the high-frequency switching to obtain fast transient response. Adjustable soft-start time provides flexibility to minimize input startup inrush current. An open-drain, power-good (PWRGD) signal goes high when the output reaches 90% of its regulation point.The MAX8566 provides a SYNCOUT output to synchronize a second MAX8566 or a second regulator switching 180° out-of-phase with the first to reduce the input ripple current, which consequently reduces the input-capacitance requirements. The MAX8566 also provides an external reference input (REFIN) for output-tracking applications.The MAX8566 is available in a 32-pin, 5mm x 5mm TQFN package. The MAX8566 and all the required external components fit into a footprint of less than 0.80in².ApplicationsASIC/CPU/DSP Core VoltagesBase-Station Power SuppliesDDR Power SuppliesFiber Power SuppliesNetwork-Power SuppliesPOL Power SuppliesTelecom Power Supplies

The DS3900 provides bidirectional communication with2-wire and 3-wire devices using a PC's serialport. In addition, it can also be used as a general-purposedigital I/O interface with 11 I/O signals that canevaluate a wide variety of ICs.The DS3900 is intended for evaluation purposes only.ApplicationsBuilding Test Software for Systems Containing 2-Wire or 3-Wire DevicesCommunicating with ICs that Require up to 11 I/O SignalsEvaluating 2-Wire and 3-Wire DevicesPrototyping 2-Wire and 3-Wire Device Designs

GNSS / GPS Development Tools

Power Management IC Development Tools EVKit for 60V, 2A Power Limiter with Current Foldback (1.0x InitialCurrent Limit)

GPS Development Tools

Solar-Powered BLE Sensor Beacon Expansion Pack

Interface Development Tools EVKit for 2.75KVrms 4 channel Digital Isolator