Analog to Digital Converters - ADC 16-BIT 100ksps I.C.

Standard (General Purpose) Amplifier 2 Circuit Rail-to-Rail 8-MSOP

Hot Swap Voltage Controllers ON Pin + Latched Off I.C.

Operational Amplifiers - Op Amps High Spd CMOS RR Video Amp

18 V, 725 A, 4 MHz CMOS RRIO Operational Amplifier Features: Low power at high voltage (18 V): 725 μA maximum Low offset voltage: 2.2 mV maximum over entire common-mode range Low input bias current: 15 pA maximum Gain bandwidth product: 4 MHz typical at Av = 100 Unity-gain crossover: 4 MHz typical −3 dB closed-loop bandwidth: 2.1 MHz typical Single-supply operation: 3 V to 18 V Dual-supply operation: ±1.5 V to ±9 V Unity-gain stable

2.5 V to 5.5 V, 500 A, 2-Wire Interface Quad Voltage Output 12-Bit DAC in a 10-Lead MicroSOIC Package Features: AD5305: 4 buffered 8-bit DACs in 10-lead MSOP A version: ±1 LSB INL, B version: ±0.625 LSB INL AD5315: 4 buffered 10-bit DACs in 10-lead MSOP A version: ±4 LSB INL, B version: ±2.5 LSB INL AD5325: 4 buffered 12-bit DACs in 10-lead MSOP A version: ±16 LSB INL, B version: ±10 LSB INL 2-wire (I2C®-compatible) serial interface 2.5 V to 5.5 V power supply Guaranteed monotonic by design over all codes Power-down to 80 nA @ 3 V, 200 nA @ 5 V  Low power operation: 500 μA @ 3 V, 600 μA @ 5 V Three power-down modes Double-buffered input logic Output range: 0 V to VREF Power-on reset to 0 V Simultaneous update of outputs (LDAC function) Software clear facility Data readback facility On-chip rail-to-rail output buffer amplifiers Temperature range: −40°C to +105°C 

16-Bit, Single-Channel, Ultra Low Power, Sigma-Delta A/D Converter Features: 16-bit resolution Power Supply: 2.5 V to 5.25 V operation Normal: 75 µA maximum Power-down: 1 µA maximum RMS noise: 1.5 µV 16-bit p-p resolution Integral nonlinearity: 3.5 ppm typical Simultaneous 50 Hz and 60 Hz rejection Internal clock oscillator VDD monitor channel 10-lead MSOP

1 MSPS, 12-Bit A/D Converter in MSOP-8 or SOIC-8 Features: Fast throughput rate: 1 MSPS Specified for VDD of 2.7 V to 5.25 V Low power: 4.5 mW max at 1 MSPS with 3 V supplies 10.5 mW max at 1 MSPS with 5 V supplies Wide input bandwidth: 68 dB SNR at 300 kHz input frequency Flexible power/serial clock speed management No pipeline delays High speed serial interface SPI-/QSPI™-/MICROWIRE-/DSP-compatible On-board reference: 2.5 V (AD7495 only) Standby mode: 1 μA max 8-lead MSOP and SOIC packages

Low Cost, High Speed Rail-to-Rail Amplifier (Dual) Features:Low cost single (AD8091) and dual (AD8092) amplifiers Fully specified at +3 V, +5 V, and 5 V supplies Single-supply operation Output swings to within 25 mV of either rail High speed and fast settling on 5 V110 MHz, 3 dB bandwidth (G = +1)145 V/s slew rate50 ns settling time to 0.1% Good video specifications (G = +2)Gain flatness of 0.1 dB to 20 MHz; RL = 150 0.03% differential gain error; RL = 1 k0.03%differential phase error; RL = 1 kLow distortion 80 dBc total harmonic @ 1 MHz; RL = 100 Outstanding load drive capabilityDrives 45 mA, 0.5 V from supply railsDrives 50 pF capacitive load (G = +1) Low power of 4.4 mA per amplifier

Single-Supply, Low Cost Instrumentation Amplifier Features:Gain set with 1 resistor per amplifierGain = 5 to 1000InputsVoltage range to 150 mV below negative rail25 nA maximum input bias current30 nV/Hz, RTI noise @ 1 kHzPower suppliesDual supply: 2V to 12Single supply: 3V to 24V500 A maximum supply current