Micropower 3-Sensor Combination Including Acceleration and Temperature Features: All sensors sampled synchronously Up to 400 Hz ODR Samples can be synchronized to external trigger Ultralow power 1.95 A at 100 Hz ODR, 2.0 V supply, all sensors on 270 nA at 6 Hz motion activated wake-up mode 10 nA standby current 12-bit resolution for all sensors Acceleration scale factor down to 1 mg/LSB Temperature scale factor: 0.065C/LSB (typical) Built-in features for motion-based system level power savings Adjustable threshold sleep/wake modes for motion activation Accelerometer, temperature sensor, and provision for third analog sensor input Autonomous interrupt processing, without need for microcontroller intervention, to allow the rest of the system to be turned off completely Deep embedded FIFO minimizes host processor load Awake state output enables implementation of standalone, motion activated switch Wide supply and I/O voltage ranges: 1.6 V to 3.5 VOperates off 1.8 V to 3.3 V railsPower can be derived from coin cell batterySPI digital interfaceSmall and thin 3 mm 3.25 mm 1.06 mm package

Micropower, 3-Axis, 200 g Digital Output, MEMS Accelerometer Features: ±200 g measurement range 160 Hz to 2560 Hz user selectable bandwidth with four-pole antialiasing filter Selectable oversampling ratio Adjustable high-pass filter Ultra low power Power can be derived from a coin cell battery 28 µA at 2560 Hz ODR, 3.3 V supply Low power, wake-up mode for low g activity detection 1.7 A instant on mode with adjustable threshold Built in features for system level power savings Autonomous interrupt processing without processor intervention Ultra low power event monitoring detects impacts and wakes up fast enough to capture the transient events Adjustable, low g threshold activity and inactivity detection Wide operating voltage range: 2.5 V to 3.5 V Acceleration sample synchronization via external trigger SPI digital interface and I2C interface format support 12-bit output at 100 mg/LSB scale factor Wide temperature range: 40°C to +105°C Small, thin, 3 mm × 3.25 mm × 1.06 mm package

Ultralow noise, dual-axis MEMS Gyroscope for Stabilization Applications Features: Pitch and roll rate gyroscope Ultralow noise: 0.004°/s/√Hz High vibration rejection over a wide frequency range Power saving standby mode 80 µA current consumption in standby mode Fast startup time from standby mode: <100 ms Low delay of <0.5 ms for a 30 Hz input at the widest bandwidth setting Serial peripheral interface (SPI) digital output Programmable high-pass and low-pass filters 2000 g powered acceleration survivability 2.7 V to 5.0 V operation −25°C to +85°C operation 4.5 mm × 5.8 mm × 1.2 mm cavity laminate package

The ADXL213 is a low cost, low power, complete dual axis accelerometer with signal conditioned, duty cycle modulated outputs, all on a single monolithic IC. The ADXL213 measures acceleration with a full-scale range of ±1.2 g (typical). The ADXL213 can measure both dynamic acceleration (e.g., vibration) and static acceleration (e.g., gravity).The outputs are digital signals whose duty cycles (ratio of pulse width to period) are proportional to acceleration (30%/g). The duty cycle outputs can be directly measured by a microcontroller without an A/D converter or glue logic.Innovative design techniques are used to ensure high zero g bias stability (typically better than 0.25 mg/°C), as well as tight sensitivity stability (typically better than 50 ppm/°C).The typical noise floor is 160 μg/√, allowing signals below 1 mg (0.06° of inclination) to be resolved in tilt sensing applications using narrow bandwidths (The user selects the bandwidth of the accelerometer usingcapacitors CX and CYM at the XFILT and YFILT pins. Bandwidths of0.5 Hz to 250 Hz may be selected to suit the application.The ADXL213 is available in a 5mm x 5mm x 2mm, 8-pad hermetic LCC package.ApplicationsAutomotive tilt alarmData projectorsNavigationPlatform stabilization/levelingAlarms and motion detectorsHigh accuracy, 2-axis tilt sensing

The ADIS16203 is a complete incline-angle measurement system ina single compact package enabled by the Analog Devices, Inc.,iSensor™ integration. By enhancing the Analog Devices iMEMS®sensor technology with an embedded signal processing solution, the ADIS16203 provides factory-calibrated, sensor-to-digital incline-angle data in a convenient format that can be accessed using aserial peripheral interface (SPI). The SPI interface provides access to multiple measurements: 360° linear inclination angles, ±180°linear incline angles, temperature, power supply, and one auxiliaryanalog input. Easy access to calibrated digital sensor data providesdevelopers with a system-ready device, reducing developmenttime, cost, and program risk.Unique characteristics of the end system are accommodatedeasily through several built-in features, such as a single-command offset calibration, along with convenient sample rate and band-width control.The ADIS16203 offers the following embedded features that eliminate the need for external circuitry and provide a simplified system interface: Configurable alarm function Auxiliary 12-bit analog-to-digital converter (ADC) Auxiliary 12-bit digital-to-analog converter (DAC) Configurable digital I/O port Digital self-test functionThe ADIS16203 offers two power management features formanaging system-level power dissipation: low power mode anda configurable shutdown feature.The ADIS16203 is available in a 9.2 mm × 9.2 mm × 3.9 mmlaminate-based land grid array (LGA) package with a temperature range of −40°C to +125°C.APPLICATIONS Tilt sensing, inclinometers Platform control, stabilization, and leveling Motion/position measurement Monitor/alarm devices (security, medical, safety) Robotics

The ADXL203 is a high precision, low power, complete dual-axis accelerometer with signal conditioned voltage outputs, all on a single, monolithic IC. The ADXL203 measures acceleration with a full-scale range of ?1.7 g, ?5 g, or ?18 g. The ADXL203 can measure both dynamic acceleration (for example, vibration) and static acceleration (for example, gravity).The typical noise floor is 110 ?g/?Hz, allowing signals below 1 mg (0.06? of inclination) to be resolved in tilt sensing applications using narrow bandwidths (<60 Hz). The user selects the bandwidth of the accelerometer using Capacitor CX and Capacitor CY at the XOUT and YOUT pins. Bandwidths of 0.5 Hz to 2.5 kHz can be selected to suit the application.The ADXL203 is available in a 5 mm ? 5 mm ? 2 mm, 8-terminal ceramic LCC package.Applications: Platform stabilization/leveling Navigation Alarms and motion detectors High accuracy, 2-axis tilt sensing Vibration monitoring and compensation Abuse event detection

The ADXL1001/ADXL1002 deliver ultralow noise density over an extended frequency range with two full-scale range options, and are optimized for industrial condition monitoring. The ADXL1001 (?100 g) and the ADXL1002 (?50 g) have typical noise densities of 30 ?g/?Hz and 25 ?g/?Hz, respectively. Both accelerometer devices have stable and repeatable sensitivity, which is immune to external shocks up to 10,000 g.The ADXL1001/ADXL1002 have an integrated full electrostatic self test (ST) function and an overrange (OR) indicator that allow advanced system level features and are useful for embedded applications. With low power and single-supply operation of 3.3 V to 5.25 V, the ADXL1001/ADXL1002 also enable wireless sensing product design. The ADXL1001/ ADXL1002 are available in a 5 mm ? 5 mm ? 1.80 mm LFCSP package, and are rated for operation over a ?40?C to +125?C temperature range.Applications Condition monitoring Predictive maintenance Asset health Test and measurement Health usage monitoring sytems (HUMS)

The ADXL1005 delivers ultralow noise density over an extended frequency range and is optimized for bearing fault detection and diagnostics. The ADXL1005 has typical noise density of 75 ?g/?Hz across the linear frequency range. Microelectronicmechanical systems (MEMS) accelerometers have stable and repeatable sensitivity, and are immune to external shocks up to 10,000?g.The integrated signal conditioning electronics enable such features as full electrostatic self test (ST) and an overrange (OR) indicator, useful for embedded applications. With low power and single-supply operation of 3.3 V to 5.25 V, the ADXL1005 also enables wireless sensing product design. The ADXL1005 is available in a 5 mm ? 5 mm ? 1.80 mm LFCSP package, and operates over the ?40?C to +125?C temperature range.APPLICATIONS Condition monitoring Predictive maintenance Asset health Test and measurement Health usage monitoring system (HUMSs) Acoustic emissions

The ADXL313 is a small, thin, low power, 3-axis accelerometer with high resolution (13-bit) measurement up to ?4g. Digital output data is formatted as 16-bit twos complement and is accessible through either a serial port interface (SPI) (3-wire or 4-wire) or I2C digital interface.The ADXL313 is well suited for car alarm or black box applications. It measures the static acceleration of gravity in tilt-sensing applications, as well as dynamic acceleration resulting from motion or shock. Its high resolution (1024 LSB/g) and low noise (150 ?g/?Hz) enable resolution of inclination changes of as little as 0.1?. A built-in FIFO facilitates using oversampling techniques to improve resolution to as little as 0.025? of inclination.Several built-in sensing functions are provided. Activity and inactivity sensing detects the presence or absence of motion and whether the acceleration on any axis exceeds a user-set level. These functions can be mapped to interrupt output pins. An integrated 32-level FIFO can be used to store data to minimize host processor intervention, resulting in reduced system power consumption.Low power modes enable intelligent motion-based power management with threshold sensing and active acceleration measurement at extremely low power dissipation.The ADXL313 is supplied in a small, thin 5 mm ? 5 mm ? 1.45 mm, 32-lead LFCSP package and is pin compatible with the ADXL312 accelerometer device.APPLICATIONS Car alarms Hill start aid (HSA) systems Electronic parking brakes Data recorders (black boxes)

The EVAL-ADXL314Z is a simple evaluation board that allows quick evaluation of the performance of the ADXL314, 3-axis digital accelerometer. The EVAL-ADXL314Z is ideal for evaluation of the ADXL314 in an existing system because the stiffness and the small size of the EVAL-ADXL314Z minimizes the effect of the board on both the system and acceleration measurements. For full details on the ADXL314, see the ADXL314 data sheet, which should be consulted in conjunction with the user guide when using the EVAL-ADXL314Z evaluation board.