The LTM4628 is a complete dual 8A output switching mode DC/DC power supply and can be easily configured to provide a single 2-phase 16A output. Included in the package are the switching controller, power FETs, inductor, and all supporting components. Operating from an input voltage range of 4.5V to 26.5V, the LTM4628 supports two outputs each with an output voltage range of 0.6V to 5.5V, set by a single external resistor. Its high efficiency design delivers 8A continuous current for each output. Only a few input and output capacitors are needed.The device supports frequency synchronization, multiphase operation, Burst Mode operation and output voltage tracking for supply rail sequencing. It has an on-board temperature diode for device temperature monitoring. High switching frequency and a current mode architecture enable a very fast transient response to line and load changes without sacrificing stability.Fault protection features include overvoltage and overcurrent protection. The power module is offered in space saving and thermally enhanced 15mm × 15mm × 4.32mm LGA and 15mm × 15mm × 4.92mm BGA packages. The LTM4628 is available with SnPb (BGA) or RoHS compliant terminal finish.Applications Telecom and Networking Equipment Storage and ATCA Cards Industrial Equipment

Power Management IC Development Tools LT4356CDE-2 Demo - Overvoltage Protectio

Power Management IC Development Tools LTM4614EV Demo Board - Low Voltage, Dual

The ADM1069 Super Sequencer® is a configurable supervisory/sequencing device that offers a single-chip solution for supplymonitoring and sequencing in multiple supply systems. In additionto these functions, the ADM1069 integrates a 12-bit analog-todigitalconverter (ADC) and four 8-bit voltage output digital-toanalogconverters (DACs). These circuits can implement a closedloopmargining system that enables supply adjustment by alteringeither the feedback node or reference of a dc-to-dc converterusing the DAC outputs.For more information about the ADM1069 register map, referto the AN-721 Application Note.Applications Central office systems Servers/routers Multivoltage system line cards DSP/FPGA supply sequencing In-circuit testing of margined supplies

The ADM690A / ADM692A / ADM802L/M / ADM805L/M family of supervisory circuits offers complete single chip solutions for power supply monitoring and battery control functions in microprocessor systems. These functions include mP reset, backup battery switchover, watchdog timer, and power failure warning.The ADM690A / ADM692A / ADM802L/M / ADM805L/M are available in 8-pin packages and provide: Power-on reset output during power-up, power-down and brownout conditions. The RESET output remains operational with VCC as low as 1 V. Battery backup switching for CMOS RAM, CMOS microprocessor or other low power devices. A reset pulse if the optional watchdog timer has not been toggled within 1.6 seconds. A 1.25 V threshold detector for power fail warning, low battery detection, or to monitor a power supply other than +5 V.On the ADM690A / ADM802L / ADM805L the reset voltage threshold is 4.65 V. On the ADM692A / ADM802M / ADM805M, the reset voltage threshold is 4.40 V.The ADM802L / ADM802M guarantee power fail accuracies to ±2%.

The ADM803 supervisory circuit monitors the power supply voltage in microprocessor systems. It provides a reset output during power-up, power-down and brownout conditions. On power-up, an internal timer holds reset asserted for 240ms. This holds the microprocessor in a reset state until conditions have stabilized. The reset output remains operational with VCC as low as 1V. The ADM803 provides an active-low reset signal RESET, and has an open-drain output stage which requires an external pull-up resistor.Seven reset threshold options are available. The reset comparator features built-in glitch immunity, making it immune to fast transients on VCC.The ADM803 is available in 3-lead SC70 and consumes only 17µA, making it suitable for low power portable equipment.APPLICATIONS Microprocessor Systems Computers Controllers Intelligent Instruments Automotive Systems

The ADM803 supervisory circuit monitors the power supply voltage in microprocessor systems. It provides a reset output during power-up, power-down and brownout conditions. On power-up, an internal timer holds reset asserted for 240ms. This holds the microprocessor in a reset state until conditions have stabilized. The reset output remains operational with VCC as low as 1V. The ADM803 provides an active-low reset signal RESET, and has an open-drain output stage which requires an external pull-up resistor.Seven reset threshold options are available. The reset comparator features built-in glitch immunity, making it immune to fast transients on VCC.The ADM803 is available in 3-lead SC70 and consumes only 17µA, making it suitable for low power portable equipment.APPLICATIONS Microprocessor Systems Computers Controllers Intelligent Instruments Automotive Systems

The ADM8690–ADM8695 family of supervisory circuits offers complete single chip solutions for power supply monitoring and battery control functions in microprocessor systems. These functions include mPreset, backup battery switchover, watchdog timer, CMOS RAM write protection and power failure warning. The complete family provides a variety of configurations to satisfy most microprocessor system requirements.The ADM8690, ADM8692 and ADM8694 are available in 8-pin DIP packages and provide: Power-on reset output during power-up, power-down and brownout conditions. The RESET output remains operational with VCC as low as 1 V. Battery backup switching for CMOS RAM, CMOS microprocessor or other low power logic. A reset pulse if the optional watchdog timer has not been toggled within a specified time. A 1.3 V threshold detector for power fail warning, low battery detection or to monitor a power supply other than +5 V.The ADM8691, ADM8693 and ADM8695 are available in 16-pin DIP and small outline packages (including TSSOP) and provide three additional functions: Write protection of CMOS RAM or EEPROM. Adjustable reset and watchdog timeout periods. Separate watchdog timeout, backup battery switchover, and low VCC status outputs.

The ADP1111 is part of a family of step-up/step-down switchingregulators that operates from an input voltage supply of 2 Vto 12 V in step-up mode and up to 30 V in step-down mode.The ADP1111 can be programmed to operate in step-up/stepdownor inverting applications with only 3 external components.The fixed outputs are 3.3 V, 5 V and 12 V; and an adjustableversion is also available. The ADP1111 can deliver 100 mA at5 V from a 3 V input in step-up mode, or it can deliver 200 mAat 5 V from a 12 V input in step-down mode.Maximum switch current can be programmed with a singleresistor, and an open collector gain block can be arranged inmultiple configuration for low battery detection, as a post linearregulator, undervoltage lockout, or as an error amplifier.APPLICATIONS 3 V to 5 V, 5 V to 12 V Step-Up Converters 9 V to 5 V, 12 V to 5 V Step-Down Converters Laptop and Palmtop Computers Cellular Telephones Flash Memory VPP Generators Remote Controls Peripherals and Add-On Cards Battery Backup Supplies Uninterruptible Supplies Portable Instruments

The ADR130 is the first family of tiny, micropower, low voltage, high precision voltage references in the industry. Featuring0.35% initial accuracy and 25 ppm/°C of temperature drift inthe tiny TSOT-23 package, the ADR130 voltage reference only requires 80 μA for typical operation. The ADR130 design includes a proprietary temperature drift curvature correction technique that minimizes the nonlinearities in the output voltage vs. temperature characteristics.Available in the industrial temperature range of −40°C to+125°C, the ADR130 is housed in a tiny TSOT-23 package.For 0.5 V output, tie SET (Pin 5) to VOUT (Pin 4). For 1.0 V output, tie SET (Pin 5) to GND (Pin 2). All Members of the ADR130 Model VOUT Accuracy Tempco 1K Price ADR130A 0.5/1.0V ±3.5mV 50ppm/°C $0.97 ADR130B 0.5/1.0V ±1.75mV 25ppm/°C $1.60 APPLICATIONS Battery-powered instrumentation Portable medical equipment Communication infrastructure equipment