3.1VIN to 32VIN Isolated Module (Power Module) DC/DC Converter Features: Complete Switch Mode Power Supply 725VDC Isolation Wide Input Voltage Range: 3.1V to 32V Up to 440mA Output Current (VOUT = 2.5V) 2.5V to 12V Output Voltage Current Mode Control Programmable Soft-Start User Configurable Undervoltage Lockout SnPb or RoHS Compliant Finish Low Profile (11.25mm × 9mm × 4.92mm) Surface Mount BGA Package

36VIN, UltraFast, Low Output Noise 5A Module (Power Module) Regulator Features:High Performance 5A Linear Regulator with Switching Step-Down Converter for High EfficiencyDigitally Programmable VOUT: 0.8V to 1.8VInput Voltage Range: 6V to 36VVery Tight Tolerance Over Temperature, Line, Load and Transient ResponseLow Output Noise: 40μVRMS (10Hz to 100kHz)Parallel Multiple Devices for 10A or MoreAccurate Programmable Current Limit to Allow Asymmetric Power SharingAnalog Output Margining: ±10% RangeSynchronization InputStable with Low ESR Ceramic Output Capacitors15mm × 15mm × 4.92mm Surface Mount BGA PackageSnPb or RoHS Compliant Finish

60V Battery Gas Gauge with Temperature, Voltage and Current Measurement Features: Measures Accumulated Battery Charge and Discharge 3.6V to 60V Operating Range for Multiple Cells 14-Bit ADC Measures Voltage, Current and Temperature 1% Voltage, Current and Charge Accuracy ±50mV Sense Voltage Range High Side Sense I2C Interface/SMBus Interface General Purpose Measurements for Any Battery Chemistry and Capacity Configurable Alert Output/Charge Complete Input Quiescent Current Less Than 150μA Small 8-Lead 3mm × 3mm DFN Package

Active Bias Controller Features: Automatic Gate voltage adjustment (No Calibration required) Supply Voltage: 4V to 12V Digital Voltage: 3.3V to 5V Controls both Enhancement and Depletion type devices Adjustable Drain Current up to 200mA Sink/Source Gate Current Capability Optional Internal negative voltage generation that can be disabled to use external negative rail Fast Enable/Disable Trigger-out Output for Daisy Chain Power-Up and Power-Down Sequencing

10V, High Efficiency, Synchronous, No RSENSE Buck-Boost Controller Features: Single Inductor Architecture Allows VIN Above, Below or Equal to VOUT 2.7V to 10V Input and Output Range Up to 96% Efficiency Up to 10A of Output Current All N-channel MOSFETs, No RSENSE™ True Output Disconnect During Shutdown Programmable Current Limit and Soft-Start Optional Short-Circuit Shutdown Timer Output Overvoltage and Undervoltage Protection Programmable Frequency: 100kHz to 1MHz Selectable Burst Mode® Operation Available in 24-Lead (4mm × 4mm) Exposed Pad QFN Package

12 Channel Multicell Battery Monitor with Daisy Chain Interface, Generation 2 Features: Measures Up to 12 Battery Cells in Series Stackable Architecture Supports Multiple Battery Chemistries and Supercapacitors Serial Interface Daisy Chains to Adjacent Devices 0.25% Maximum Total Measurement Error Engineered for ISO26262 Compliant Systems 13ms to Measure All Cells in a System Passive Cell Balancing: Integrated Cell Balancing MOSFETs Ability to Drive External Balancing MOSFETs On-board Temperature Sensor and Thermistor Inputs 1MHz Serial Interface with Packet Error Checking Safe with Random Connection of Cells Built-In Self Tests Delta-Sigma Converter With Built-In Noise Filter Open-Wire Connection Fault Detection 12μA Standby Mode Supply Current High EMI Immunity 44-Lead SSOP Package

LDO VOLTAGE REGULATORS ROHS COMPLIANT: YES

Power Management IC Development Tools LTC4354 Demoboard - Dual -48V, 5A Ideal

Power Management IC Development Tools LTC1734ES6-4.1 - Li-Ion Battery Charger

The ADM1066 Super Sequencer® is a configurable supervisory/ sequencing device that offers a single-chip solution for supply monitoring and sequencing in multiple-supply systems. In addition to these functions, the ADM1066 integrates a 12-bit ADC and six 8-bit voltage output DACs. These circuits can be used to implement a closed-loop margining system that enables supply adjustment by altering either the feedback node or reference of a dc-to-dc converter using the DAC outputs. Supply margining can be performed with a minimum of external components. The margining loop can be used for in-circuit testing of a board during production (for example, to verify board functionality at −5% of nominal supplies), or it can be used dynamically to accurately control the output voltage of a dc-to-dc converter.APPLICATIONS Central office systems Servers/routers Multivoltage system line cards DSP/FPGA supply sequencing In-circuit testing of margined supplies