Analog to Digital Converters - ADC CMOS CONVERTER IC

Phase Locked Loops - PLL 1000-2500MHz Frac-N PLL

Linear Voltage Regulator IC Positive Fixed 1 Output 200mA 4-WLCSP (0.76x0.76)

Linear Voltage Regulators 300mA LDO 1.8Vout

GaAs InGaP HBT MMIC Ultra Low Phase Noise, Distributed Amplifier, 2 - 18 GHz Features: Ultra Low Phase Noise: -160 dBc/Hz @ 10 kHz P1dB Output Power: +15 dBm Gain: 14 dB Output IP3: +27 dBm Supply Voltage: +5V @ 64 mA 50 Ω Matched Input/Output Die Size: 2.80 x 1.73 x 0.1 mm

2.5 V to 5.5 V, 230 A, Dual Rail-to-Rail Voltage Output 12-Bit DAC Features: AD5313: 2 buffered 10-bit DACs in 1 package A version: ±4 LSB INL B version: ±2 LSB INL AD5323: 2 buffered 12-bit DACs in 1 package A version: ±16 LSB INL  B version: ±8 LSB INL 16-lead TSSOP package Power-down to 200 nA @ 5 V, 50 nA @ 3 V Micropower operation: 300 μA at 5 V (including reference current) 2.5 V to 5.5 V power supply Double-buffered input logic Guaranteed monotonic by design over all codes Buffered/unbuffered reference input options Output range: 0 V to VREF or 0 V to 2 VREF Power-on-reset to 0 V

18-Cell Battery Monitor with Daisy Chain Interface Features: Measures up to 18 battery cells in series 3 mV maximum total measurement error Stackable architecture for high voltage systems Built-in isoSPI interface 1 Mb isolated serial communications Uses a single twisted pair, up to 100 meters Low EMI susceptibility and emissions Bidirectional for broken wire protection 290 μs to measure all cells in a system Synchronized voltage and current measurement 16-bit Δ-Σ ADC with programmable third-order noise filter Passive cell balancing up to 200 mA (maximum) with programmable pulsewidth modulation 9 general purpose digital I/O or analog inputs Temperature or other sensor inputs Configurable as an I2C or SPI master 6 μA sleep mode supply current 64-lead LQFP_EP package

Dual Channel, Configurable, IsolatedDigital Input Features: Dual channel, configurable, isolated digital input Programmable trip threshold On-chip debounce filter On-chip data and power Isolation Application circuit monitors wide voltage range 10 V dc to 300 V dc 8 V rms to 240 V rms ac (with 10 ms + pickup) Negative dc protected Programmable wetting current Pulse up to 50 mA Constant current up to 6.3 mA Safety and regulatory approvals UL recognition 3750 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice #5A (pending) CSA 61010-1: 300 V rms VDE certificate of conformity (pending) DIN V VDE V 0884-11 (VDE V 0884-11):2017-1 VIORM = 565 V peak EMC robust solution supports relay protection system level requirements ADC samples available for system diagnostics Internal SAR ADC with PGA Single 3.3 V Supply Integrated isoPower, isolated dc-to-dc converter Interfaces SPI DOUTx output reflects state of digital input IRQ interrupt pin Operating temperature: −40°C to +125°C 20-lead, LGA package with 6.8 mm creepage

High Performance Polyphase Energy Measurement IC Features: 7 high performance analog-to-digital converters (ADCs) 101 dB signal-to-noise ratio (SNR) 10,000:1 dynamic range Wide input range: ±1 V, 0.707 V rms full scale Differential inputs ±25 ppm/°C maximum channel temperature drift (including ADC, internal VREF, and PGA drift) enabling Class 0.2 meters with standard external components Power quality measurements Line frequency: 1 measurement per phase Zero crossing detection, zero-crossing timeout Phase angle measurements Supports current transformers (CTs) and Rogowski coil (di/dt) sensors Multiple range phase/gain compensation for CTs Digital integrator for Rogowski coils Flexible waveform buffer Able to resample waveform to ensure 64 points per line cycle for ease of external harmonic analysis Events can trigger waveform storage Simplifies data collection for IEC 61000-4-7 harmonic analysis Advanced metrology feature set Total active power, volt-amperes reactive (VAR), volt-amperes (VA), watthour, VAR-hour, and VA-hour Fundamental VAR and VAR-hour Current and voltage rms per phase (xIRMS, xVRMS) Supports active energy standards: IEC 62053-21, IEC 62053-22; EN50470-3; OIML R46, ANSI C12.20 Supports reactive energy standards: IEC 62053-23, IEC 62053-4 High speed communication port 10 MHz serial peripheral interface (SPI)

0.4 CMOS, Dual DPDT Switch in WLCSP/LFCSP/TSSOP Features: 1.8 V to 5.5 V operation Ultralow on resistance 0.4 Ω typical 0.6 Ω maximum at 5 V supply Excellent audio performance, ultralow distortion 0.07 Ω typical 0.14 Ω maximum RON flatness High current carrying capability 400 mA continuous 600 mA peak current at 5 V Automotive temperature range: −40°C to +125°C Rail-to-rail switching operation Typical power consumption (<0.1 μW)