The ADG5243F comprises three independently selectable, singlepole/double-throw (SPDT) switches. All channels exhibit break-before-make switching action that prevents momentary shorting when switching channels. An EN input enables or disables the device. When disabled, all channels are switched off. Each switch conducts equally well in both directions when on, and each switch has an input signal range that extends to the supplies. The primary supply voltages define the on-resistance profile, whereas the secondary supply voltages define the voltage level at which the overvoltage protection engages.When no power supplies are present, the channel remains in the off condition, and the switch inputs are high impedance. Undernormal operating conditions, if the analog input signal levels on any Sx pin exceed the positive fault voltage (POSFV) or the negative fault voltage (NEGFV) by a threshold voltage (VT), the channel turns off and that Sx pin becomes high impedance. If the switch is selected to be on, then the drain pin is pulled to the secondary supply voltage that was exceeded. Input signal levels upto ?55 V or +55 V relative to ground are blocked, in both the powered and unpowered conditions.The low capacitance and charge injection of these switches make them ideal solutions for data acquisition and sample-andholdapplications, where low glitch switching and fast settling times are required.Note that, throughout this data sheet, multifunction pins, such as IN1/F1, are referred to either by the entire pin name or by asingle function of the pin, for example, IN1, when only that function is relevant.Product Highlights The source pins are protected against voltages greater than?the secondary supply rails, up to ?55 V and +55 V. The source pins are protected against voltages between??55 V and +55 V in an unpowered state. Overvoltage detection with the digital output indicates the?operating state of the switches. Trench isolation guards against latch-up. Optimized for low charge injection and on-capacitance. The ADG5243F can be operated from a dual supply of ?5 V?to ?22 V or a single power supply of 8 V to 44 V.Applications Analog input/output modules? Process control/distributed control systems? Data acquisition? Instrumentation? Avionics? Automatic test equipment? Communication systems? Relay replacement?

The ADG5248F and ADG5249F are 8:1 and dual 4:1 analog multiplexers. The ADG5248F switches one of eight inputs to a common output and the ADG5249F switches one of four differential inputs to a common differential output. Each channel conducts equally well in both directions when on, and each channel has an input signal range that extends to the supplies. The primary supply voltages define the on-resistance profile, whereas the secondary supply voltages define the voltage level at which the overvoltage protection engages.When no power supplies are present, the channel remains in the off condition, and the switch inputs are high impedance. Under normal operating conditions, if the analog input signal levels on any Sx pin exceed positive fault voltage (POSFV) or negative fault voltage (NEGFV) by a threshold voltage (VT), the channel turns off and that Sx pin becomes high impedance. If the switch is selected to be on, then the drain pin is pulled to the secondary supply voltage that was exceeded. Input signal levels up to +55 V or ?55 V relative to ground are blocked, in both the powered and unpowered condition.The low capacitance and charge injection of these switches make them ideal solutions for data acquisition and sample-and-hold applications, where low glitch switching and fast settling times are required.?Note that, throughout this data sheet, multifunction pins, such as A0/F2, are referred to either by the entire pin name or by a single function of the pin, for example, A0, when only that function is relevant.?Product Highlights Source pins are protected against voltages greater than the secondary supply rails, up to ?55 V and +55 V. Source pins are protected against voltages between ?55 V and +55 V in an unpowered state. Overvoltage detection with digital output indicates operating state of switches. Trench isolation guards against latch-up. Optimized for low charge injection and on-capacitance. The ADG5248F/ADG5249F can be operated from a dual?supply of ?5 V to ?22 V or a single power supply of 8 V to 44 V.Applications Analog input/output modules Process control/distributed control systems Data acquisition Instrumentation Avionics Automatic test equipment Communication systems Relay replacement

The ADG854 is a low voltage CMOS device containing two independently selectable single-pole, double-throw (SPDT) switches. This device offers ultralow on resistance of less than 0.8 ? over the full temperature range. The ADG854 is fully specified for 5.5 V, 3.3 V, and 2.5 V supply operation. Each switch conducts equally well in both directions when on, and has an input signal range that extends to the supplies. The ADG854 exhibits break-before-make switching action. The ADG854 is available in a 1.6 mm ? 1.3 mm 10-lead mini LFCSP package.Applications Cellular phones PDAs MP3 players Power routing Battery-powered systems PCMCIA cards Modems Audio and video signal routing Communication systems

The ADGS1412 contains four independent single-pole/single-throw(SPST) switches. A serial peripheral interface (SPI)controls the switches. The SPI interface has robust error detectionfeatures such as cyclic redundancy check (CRC) error detection,invalid read/write address detection, and SCLK count errordetection.It is possible to daisy-chain multiple ADGS1412 devices together.Daisy-chain mode enables the configuration of multiple deviceswith a minimal amount of digital lines. The ADGS1412 can alsooperate in burst mode to decrease the time between SPIcommands.iCMOS construction ensures ultralow power dissipation, makingthe device ideally suited for portable and battery-poweredinstruments.Each switch conducts equally well in both directions when on,and each switch has an input signal range that extends to thesupplies. In the off condition, signal levels up to the suppliesare blocked.The on-resistance profile is flat over the full analog input range,which ensures good linearity and low distortion when switchingaudio signals.Product Highlights SPI interface removes the need for parallel conversion, logic traces and reduces general-purpose input/output (GPIO) channel count. Daisy-chain mode removes additional logic traces when multiple devices are used. CRC error detection, invalid read/write address detection, and SCLK count error detection ensures a robust digital interface. CRC and error detection capabilities allow the use of the ADGS1412 in safety critical systems. Guaranteed break-before-make switching allows the use of the ADGS1412 in multiplexer configurations with external wiring. Minimum distortion.Applications Automated test equipment Data acquisition systems Battery-powered systems Sample-and-hold systems Audio signal routing Video signal routing Communications systems Relay replacement

8-Channel/4-Channel Fault-Protected Analog Multiplexers

CMOS, 2.5 Low Voltage 16 Channel Multiplexer Features: +1.8 V to +5.5 V single supply ±2.5 V dual supply 2.5 ON resistance 0.5 ON resistance flatness 100 pA leakage currents 40 ns switching times Single 16-to-1 multiplexer 28-lead TSSOP package Low-power consumption TTL/CMOS-compatible inputs

ANALOGUE SWITCH DUAL SPDT LFCSP-12; Analogue Switch Type:SPDT; No. of Channels:2Channels; On State Resistance Max:475ohm; Supply Voltage Range:12V ± 15V; Analogue Switch Case:LFCSP; No. of Pins:12Pins; Operating Temperature Min:-40°C; Operating Temperature Max:125°C; Packaging:Each; Product Range:ADG1236 Series; Automotive Qualification Standard:-; MSL:MSL 3 - 168 hours; SVHC:No SVHC (20-Jun-2016)

ANALOG MULTIPLEXER 8X1 LFCSP-16; Multiplexer Configuration:8:1; No. of Circuits:1Circuits; On State Resistance Max:75ohm; Supply Voltage Range:2V to 12V ± 2V to ± 6V; Analogue Multiplexer Case:LFCSP; No. of Pins:16Pins; Operating Temperature Min:-40°C; Operating Temperature Max:85°C; Packaging:Each; Product Range:ADG658 Series; Automotive Qualification Standard:-; MSL:MSL 3 - 168 hours; SVHC:No SVHC (20-Jun-2016)

ANALOG SWITCH SINGLE SPDT SC-70-6 FULL REEL; Analog Switch Type:SPDT; No. of Channels:1Channels; On State Resistance Max:2.5ohm; Supply Voltage Range:1.8V to 5.5V; Analog Switch Case:SC-70; No. of Pins:6Pins; Product Range:-

+/- 15V 4:1 MUX WITH LOW CAP I.C.; Multiplexer Configuration:4:1; No. of Circuits:1Circuits; On State Resistance Max:190ohm; Supply Voltage Range:10.8V to 13.2V ± 13.5V to ± 16.5V; Analogue Multiplexer Case:LFCSP; No. of Pins:12Pins; Operating Temperature Min:-40°C; Operating Temperature Max:125°C; Packaging:Cut Tape; Product Range:ADG1204 Series; Automotive Qualification Standard:-; MSL:MSL 3 - 168 hours; SVHC:No SVHC (20-Jun-2016); Analogue Switch Case Style:LFCSP; Supply Current:170µA