20 V, 6 A, Synchronous, Step-Down DC-to-DC Regulator Features: Input voltage range: 4.5 V to 20 V Integrated MOSFET: 44 mΩ typical/11 mΩ typical Reference voltage: 0.6 V ± 1% Continuous output current: 6 A Programmable current-limit thresholdProgrammable switching frequency: 200 kHz to 1400 kHz Precision enable and power good External compensation Internal soft start with external adjustable option Startup into a precharged output Supported by ADIsimPower design tool

18 V, 12 A Step-Down Regulator with Programmable Current Limit Features: Input voltage: 4.5 V to 18 V Continuous output current: 12 A Integrated MOSFETs: 17 mΩ high-side/4.5 mΩ low-side 0.6 V ± 0.5% reference voltage Programmable switching frequency range: 200 kHz to 2200 kHz Enhanced transient response Programmable current limit with ±10% accuracy Precision enable and power good External compensation and soft start Start up into a precharged output Supported by the ADIsimPower design tool

3 A, 36 V, Synchronous Step-Down DC-to-DC Regulator Features: Continuous output current: 3 A Input voltage: 4.5 V to 36 V Integrated MOSFETs: 98 mΩ/35 mΩ Reference voltage: 0.6 V ± 1% Fast minimum on time: 50 ns Programmable switching frequency: 200 kHz to 1.8 MHz Synchronizes to external clock: 200 kHz to 1.8 MHz Precision enable and power good Cycle-by-cycle current limit with hiccup protection External compensation Programmable soft start time Startup into a precharged output Supported by ADIsimPower design tool

600 mA, 2.5 MHz Buck-Boost DC-to-DC Converter Features: 1 mm height profile Compact PCB footprint Seamless transition between modes 38 μA typical quiescent current 2.5 MHz operation enables 1.5 μH inductor Input voltage: 2.3 V to 5.5 V Fixed output voltage: 2.8 V to 5.0 V See data sheet for additional features

0.4 CMOS, Dual DPDT Switch in WLCSP/LFCSP/TSSOP Features: 1.8 V to 5.5 V operation Ultralow on resistance 0.4 Ω typical 0.6 Ω maximum at 5 V supply Excellent audio performance, ultralow distortion 0.07 Ω typical 0.14 Ω maximum RON flatness High current carrying capability 400 mA continuous 600 mA peak current at 5 V Automotive temperature range: −40°C to +125°C Rail-to-rail switching operation Typical power consumption (<0.1 μW)

0 Hz/dc to 14 GHz, Single-Pole, Four-Throw MEMS Switch with Integrated Driver Features: Fully operational down to 0 Hz/dc On resistance: 2.9 Ω (maximum) Off leakage: 0.5 nA (maximum) −3 dB bandwidth 11 GHz (typical) for RF1, RF4 14 GHz (typical) for RF2, RF3 RF performance characteristics Insertion loss: 0.26 dB (typical) at 2.5 GHz Isolation: 24 dB (typical) at 2.5 GHz IIP3: 69 dBm (typical) RF power: 36 dBm (maximum) Actuation lifetime: 1 billion cycles (minimum) Hermetically sealed switch contacts On switching time: 75 μs (maximum) Integrated driver removes the need for an external driver Supply voltage: 3.0 V to 3.6 V CMOS-/LVTTL-compatible Parallel and SPI interface Independently controllable switches Switch is in an open state with no power supply present Requirement to avoid floating nodes on all RFx pins (see the Floating Node section in data sheet) 24-lead, 5 mm × 4 mm × 0.95 mm, LFCSP Operating temperature range: 0°C to 85°C

SPI Interface, 1.5 RON, 15 V/+12 V, Quad SPST Switch, Mux Configurable Features: SPI interface with error detection Includes CRC, invalid read/write address, and SCLK count error detection Supports burst mode and daisy-chain mode Industry-standard SPI Mode 0 and Mode 3 interface compatible Guaranteed break-before-make switching allowing external wiring of switches to deliver multiplexer configurations 1.5 typical on resistance at 25°C 0.3 typical on resistance flatness at 25°C 0.1 typical on resistance match between channels at 25°C VSS to VDD analog signal range Fully specified at ±15 V, ±5 V, and +12 V 1.8 V logic compatibility with 2.7 V ≤ VL ≤ 3.3 V 24-lead LFCSP

24 V to 220 V Precision Operational Amplifier Features: Wide range of operating voltages Dual-supply: ±12 V to ±110 V Asymmetrical supply operation: 24 V to 220 V Wide input common-mode voltage range: 3 V from rails High common-mode rejection ratio: 160 dB typical High AOL: 170 dB typical High slew rate 74 V/μs typical 24 V/μs typical with external input clamping diodes Low input bias current: 2 pA maximum Low input offset voltage: 1 mV maximum Low input offset voltage drift: 2 μV/°C maximum Low input voltage noise: 8 nV/√Hz typical at 10 kHz Wide small signal bandwidth: 10 MHz typical Resistor adjustable quiescent current: 0.6 mA to 3 mA (VS = ±110 V) Unity-gain stable Thermal monitoring Small footprint: 12-lead, 7 mm × 7 mm LFCSP compliant with IEC 61010-1 spacing Shutdown mode

Quad Voltage Monitor and Sequencer Features: Powered from 2.7 V to 5.5 V on the VCC pin Logical core with internal timeouts provides power supply sequencing and fault protection 4 inputs can be programmed to monitor different voltage levels with resistor dividers Monitors 4 supplies via 0.8% accurate comparators 3 open-drain enable outputs Open-drain power-good output (PWRGD) 10-lead MSOP

5 kV Signal Isolated, High Speed (16 Mbps), ESD Protected, Full/Half Duplex RS-485 Transceiver Features: Isolated, RS-485/RS-422 transceiver, configurable as half- or full-duplex ±8 kV ESD protection on RS-485 input/output pins 16 Mbps data rate Complies with ANSI TIA/EIA RS-485-A-1998 and ISO 8482: 1987(E) Suitable for 5 V or 3.3 V operation (VDD1) High common-mode transient immunity: >25 kV/µs Receiver has open-circuit, fail-safe design 32 nodes on the bus Thermal shutdown protection Safety and regulatory approvals UL recognition: 5000 V rms isolation voltage for 1 minute, per UL 1577 VDE certificate of conformity DIN V VDE V 0884-10 (VDE V 0884-10): 2006-12 Reinforced insulation, VIORM = 849 V peak See data sheet for additional features