Quad 16-/14-/12-Bit nanoDAC+ with 2 ppm/C Reference, I2C Interface

Cascadable IF VGAs with Programmable RMS Detectors

Zero Drift, Digitally Programmable Instrumentation Amplifier

Keypad Decoder and I/O Expansion

Single-Supply, Rail-to-Rail, Low Power FET-Input Op Amp Features: True single-supply operation Output swings rail-to-rail Input voltage range extends below ground Single-supply capability from 5 V to 36 V Dual-supply capability from ±2.5 V to ±18 V  Excellent load drive Capacitive load drive up to 350 pF Minimum output current of 15 mA  Excellent ac performance for low power 800 μA maximum quiescent current Unity-gain bandwidth: 1.8 MHz Slew rate of 3 V/μs  Excellent dc performance 800 μV maximum input offset voltage 2 μV/°C typical offset voltage drift 25 pA maximum input bias current  Low noise: 13 nV/√Hz @ 10 kHz 

The ADN8833 is a monolithic H-bridge TEC driver with integrat-ed 1 A power MOSFETs. It has a linear power stage with the linear driver (LDR) output and a pulse-width modulation (PWM) power stage with the SW output. Depending on the control voltage at the CONT input, the ADN8833 drives current through a TEC to settle the temperature of a laser diode or a passive component attached to the TEC module to the programmed target temperature.The control voltage applied to the CONT input is generated by a digital-to-analog converter (DAC) closing the digital proportional, integral, derivative (PID) loop of temperature control system.The internal 2.5 V reference voltage provides a 1% accurate output that is used to bias a voltage divider network to program the maximum TEC current and voltage limits for both the heating and cooling modes. It can also be a reference voltage for the DAC and the temperature sensing circuit, including a thermistor bridge and an analog-to-digital converter (ADC).APPLICATIONS TEC temperature control Optical modules Optical fiber amplifiers Optical networking systems Instruments requiring TEC temperature control

The AD5700/AD5700-1 are single-chip solutions, designedand specified to operate as a HART® FSK half-duplex modem,complying with the HART physical layer requirements. TheAD5700/AD5700-1 integrate all of the necessary filtering, signaldetection, modulating, demodulating and signal generationfunctions, thus requiring few external components. The 0.5%precision internal oscillator on the AD5700-1 greatly reducesthe board space requirements, making it ideal for line-poweredapplications in both master and slave configurations. The maximumsupply current consumption is 115µA, making theAD5700/AD5700-1 an optimal choice for low power loop-powered applications.Transmit waveforms are phase continuous 1200 Hz and2200 Hz sinusoids. The AD5700/AD5700-1 contain accuratecarrier detect circuitry and use a standard UART interface.Applications Field transmitters HART multiplexers PLC and DCS analog I/O modules HART network connectivity

The ADXL345 is a small, thin, low power, 3-axis accelerometer with high resolution (13-bit) measurement at up to ±16g. Digital output data is formatted as 16-bit twos complement and is accessible through either a SPI (3- or 4-wire) or I2C digital interface.The ADXL345 is well suited for mobile device applications. It measures the static acceleration of gravity in tilt-sensing applications, as well as dynamic acceleration resulting from motion or shock. Its high resolution (4 mg/LSB) enables measurement of inclination changes less than 1.0°.Several special sensing functions are provided. Activity and inactivitysensing detect the presence or lack of motion by comparingthe acceleration on any axis with user-set thresholds. Tap sensingdetects single and double taps in any direction. Free-fall sensingdetects if the device is falling. These functions can be mappedindividually to either of two interrupt output pins. An integratedmemory management system with a 32-level first in, first out (FIFO)buffer can be used to store data to minimize host processor activityand lower overall system power consumption.Low power modes enable intelligent motion-based power management with threshold sensing and active acceleration measurement at extremely low power dissipation.The ADXL345 is supplied in a small, thin, 3 mm × 5 mm × 1 mm, 14-lead, plastic package. ADXL345-EP Supports defense and aerospace applications (AQEC)APPLICATIONS Handsets Medical instrumentation Gaming and pointing devices Industrial instrumentation Personal navigation devices Hard disk drive (HDD) protection

The AD76871 is a 16-bit, charge redistribution, successive approximation, analog-to-digital converter (ADC) that operates from a single power supply, VDD, between 2.3 V to 5.5 V. It contains a low power, high speed, 16-bit sampling ADC with no missing codes, an internal conversion clock, and a versatile serial interface port. The device also contains a low noise, wide bandwidth, short aperture delay track-and-hold circuit. On the CNV rising edge, the AD7687 the samples the voltage difference between IN+ and IN− pins, which can range from −VREF to +VREF. The reference voltage, VREF, is applied externally and can be set up to the supply voltage.The power consumption of the device scales linearly with throughput.The SPI-compatible serial interface also features the ability to daisy-chain several ADCs on a single 3-wire bus and provides an optional BUSY indicator by means of the SDI pin. It is compatible with 1.8 V, 2.5 V, 3 V, or 5 V logic using the separate supply VIO.The AD7687 comes in a 10-lead MSOP or a 10-lead LFCSP with operation specified from −40°C to +85°C.APPLICATIONS Battery-powered equipment Data acquisitions Instrumentation Medical instruments Process controls

IC 12BIT ADC 40MSPS 28SSOP; Resolution (Bits):12bit; Sampling Rate:40MSPS; Supply Voltage Type:Single; Supply Voltage Min:4.75V; Supply Voltage Max:5.25V; ADC / DAC Case Style:SSOP; No. of Pins:28Pins; Input Channel Type:Differential Single Ended; Data Interface:Parallel; Operating Temperature Min:-40°C; Operating Temperature Max:85°C; Packaging:Each; Product Range:Single 12-Bit Pipelined ADCs; Automotive Qualification Standard:-; MSL:MSL 1 - Unlimited; SVHC:No SVHC (20-Jun-2016); Base Number:9224; IC Case Style:SSOP; No. of Channels:1Channels; Operating Temperature Range:-40°C to +85°C; Supply Current:82mA; Supply Voltage Range:4.75V to 5.25V; Supply Voltage Range - Analogue:4.75V to 5.25V; Supply Voltage Range - Digital:2.85V to 5.25V; Termination Type:Surface Mount Device