Quad-Channel Isolators with Integrated DC-to-DC Converter (3:1 directionality) Features: isoPower integrated, isolated dc-to-dc converter 100 mA output supply AEC-Q100 qualified for automotive applications ADuM6421AW (ADuM6423AW pending) Meets CISPR 32/EN55032 Class B emission limits up to 5 Mbps at a full load on a 2-layer PCB Quad dc to 100 Mbps signal isolation channels 28-lead, fine pitch, SOIC with 8.3 mm minimum creepage High temperature operation: 125°C maximum High common-mode transient immunity: 100 kV/μs Safety and regulatory approvals (pending) UL recognition (pending) 5000 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A (pending) VDE V 0884-11 certificate of conformity (pending) VIORM = 566 V peak CQC certification per GB4943.1-2011 (pending)

Isolated Precision Half-Bridge Driver, 4 A Output Features: 4 A peak output current Working voltage: High-side or low-side relative to input: 565 V peak High-side to low-side differential: 700 V peak High frequency operation: 1 MHz maximum Precise timing characteristics: 60 ns maximum isolator and driver Propagation Delay 7 ns maximum channel-to-channel matching 3.3 V to 5 V input Logic 4.5V to 18 V output drive UVLO at 2.5 V VDD1: A Version UVLO at 4.1 V VDD2 CMOS input logic levels High common-mode transient immunity: >25 kV/µs High junction temperature operation: 125°C Default low output 5 × 5 mm, 14-lead LGA

40MHz to 10GHz RMS Power Detector with 57dB Dynamic Range Features: Frequency Range: 40MHz to 10GHz Linear Dynamic Range: Up to 57dB Accurate RMS Power Measurement of High Crest Factor Modulated Waveforms Exceptional Accuracy Over Temperature: ±0.5dB (Typ) Low Linearity Error within Dynamic Range Single-Ended or Differential RF Inputs Fast Response Time: 90ns Rise Time Low Supply Current: 41.6mA at 3.3V (Typ) Small 3mm × 3mm DFN10 AEC-Q100 Qualified for Automotive Applications

Linear SuperCap Charger with Current-Limited Ideal Diode and V/I Monitor Features: 50mΩ Ideal Diode from VIN to VOUT Smart Charge Current Profile Limits Inrush Current Internal Cell Balancer (No External Resistors) Programmable Output Voltage (LDO Mode) Programmable VIN to VOUT Current Limit Continuous Monitoring of VIN to VOUT Current via PROG Pin Low Quiescent Current: 20μA VIN Power Fail, PGOOD Indicator 2.45V/2.7V Cell Protection Shunts (4.9V/5.4V SuperCap Max Top-Off Voltage) 3A Peak Current Limit, Thermal Limiting Tiny Application Circuit, 3mm × 3mm × 0.75mm DFN and 12-Lead MSOP Packages

Matched Dual-Channel 6GHz RMS Power Detector Features: Frequency Range: 40MHz to 6GHz Linear Dynamic Range: Up to 60dB ±0.5dB (Typ) Accuracy Over Temperature 40dB Channel-to-Channel Isolation at 2GHz Even with Single-Ended RF Inputs Matched Dual-Channel Outputs: <1.25dB (Typ) Single-Ended RF Inputs—No Transformer Required Accurate RMS Power Measurement of High Crest Factor Modulated Waveforms Difference Output Provides VSWR Measurement Fast Envelope Detector Outputs Fast Response Time: 140ns Rise Time Small 4mm × 4mm QFN24 Package 

32VIN, 2A Module (Power Module) Power Tracking Battery Charger Features:Complete Battery Charger SystemInput Supply Voltage Regulation Loop for Peak Power Tracking in MPPT (Maximum Peak Power Tracking) Solar ApplicationsResistor Programmable Float Voltage Up to 14.4V on the LTM8062 and 18.8V on the LTM8062AWide Input Voltage Range: 4.95V to 32V (40V Abs Max)2A Charge CurrentAccommodates Li-Ion/Polymer, LiFePO4, SLAIntegrated Input Reverse Voltage ProtectionUser Selectable Termination: C/10 or Termination Timer0.75% Float Voltage Reference Accuracy9mm × 15mm × 4.32mm LGA Package

2 A/1.2 A DC-to-DC Switching Regulator with Independent Positive and Negative Outputs Features: Wide input supply voltage range: 2.85 V to 15 V Generates well regulated, independently resistor programmable VPOS and VNEG outputs Boost regulator to generate VPOS output Adjustable positive output to 39 V Integrated 2.0 A main switch Optional single-ended primary-inductor converter (SEPIC) configuration for automatic step-up/step-down Inverting regulator to generate VNEG output Adjustable negative output to VIN − 39 V Integrated 1.2 A main switch True shutdown for both positive and negative outputs 1.2 MHz/2.4 MHz switching frequency with optional external frequency synchronization from 1.0 MHz to 2.6 MHz Resistor programmable soft start timer Slew rate control for lower system noise Individual precision enable and flexible start-up sequence control for symmetric start, VPOS first, or VNEG first Out-of-phase operation UVLO, OCP, OVP, and TSD protection 4 mm × 4 mm, 20-lead LFCSP and 20-lead TSSOP −40°C to +125°C junction temperature range Supported by the ADIsimPower tool set

Advanced Battery Management PMIC with Ultra Low Power Fuel Gauge, Battery Protection, Buck and Buck Boost Features: Linear battery charger High accuracy and programmable charge terminal voltage and charge current up to 320 mA Compliant with JEITA charge temperature specification Li-Ion and Li-Poly battery monitor and protection Voltage-based fuel gauge with adaptive filter limitation Independent battery protection of overcharge and overdischarge Temperature sensor with external NTC Ultralow quiescent current buck converter Quick output discharge option Ultralow quiescent current buck boost converter Quick output discharge option Supervisory with manual reset (MR) and watchdog timer Shipment mode extends battery life Full I2C programmability with dedicated interrupt pin

20 V, 200 mA, Low Noise, CMOS LDO Linear Regulator Features: Low noise: 11 μV rms independent of fixed output voltage PSRR of 88 dB at 10 kHz, 68 dB at 100 kHz, 50 dB at 1 MHz, VOUT ≤ 5 V, VIN = 7 V Input voltage range: 2.7 V to 20 V Maximum output current: 200 mA Initial accuracy: ±0.8% Accuracy over line, load, and temperature −1.2% to +1.5%, TJ = −40°C to +85°C ±1.8%, TJ = −40°C to +125°C Low dropout voltage: 200 mV (typical) at a 200 mA load,  VOUT = 5 V User programmable soft start (LFCSP and SOIC only) Low quiescent current, IGND = 50 μA (typical) with no load Low shutdown current: 1.8 μA at VIN = 5 V, 3.0 μA at VIN = 20 V Stable with a small 2.2 μF ceramic output capacitor Fixed output voltage options: 1.8 V, 2.5 V, 3.3 V, 4.5 V, and 5.0 V 16 standard voltages between 1.2 V and 5.0 V are available Adjustable output from 1.2 V to VIN – VDO, output can be adjusted above initial set point Precision enable 2 mm × 2 mm, 6-lead LFCSP, 8-Lead SOIC, 5-Lead TSOT AEC-Q100 qualified for automotive applications

40 V, 200 mA, Low Noise, CMOS LDO Linear Regulator Features: Low noise: 11 μV rms independent of fixed output voltage PSRR of 88 dB at 10 kHz, 68 dB at 100 kHz, 50 dB at 1 MHz, VOUT ≤ 5 V, VIN = 7 V Input voltage range: 2.7 V to 40 V Maximum output current: 200 mA Initial accuracy: ±0.8% Accuracy over line, load, and temperature −1.2% to +1.5%, TJ = −40°C to +85°C ±1.8%, TJ = −40°C to +125°C Low dropout voltage: 200 mV (typical) at a 200 mA load, VOUT = 5 V User programmable soft start (LFCSP and SOIC only) Low quiescent current, IGND = 50 μA (typical) with no load Low shutdown current: 1.8 μA at VIN = 6 V, 3.0 μA at VIN = 40 V Stable with a small 2.2 μF ceramic output capacitor Fixed output voltage options: 1.8 V, 2.5 V, 3.3 V, 3.8 V, and 5.0 V 15 standard voltages between 1.2 V and 5.0 V are available Adjustable output from 1.2 V to VIN – VDO, output can be adjusted above initial set point Precision enable 2 mm × 2 mm, 6-lead LFCSP, 8-Lead SOIC, 5-Lead TSOT AEC-Q100 qualified for automotive applications