Low Cost, Low Power, True RMS-to-DC Converter Features: Converts an ac voltage waveform to a dc voltage and then converts to the true rms, average rectified, or absolute value 200 mV rms full-scale input range (larger inputs with input attenuator) High input impedance: 1012 Ω  Low input bias current: 25 pA maximum High accuracy: ±0.3 mV ± 0.3% of reading RMS conversion with signal crest factors up to 5 Wide power supply range: +2.8 V, −3.2 V to ±16.5 V Low power: 200 μA maximum supply current Buffered voltage output No external trims needed for specified accuracy Related device: the AD737 features a power-down control with standby current of only 25 μA; the dc output voltage is negative and the output impedance is 8 kΩ

60VIN, 3A Silent Switcher Module Regulator Features: Complete Step-Down Switch Mode Power Supply Low Noise Silent Switcher® Architecture Wide Input Voltage Range: 3.4V to 60V Wide Output Voltage Range: 0.8V to 15V 3A Continuous Output Current, 5A Peak Parallelable for Increased Output Current Selectable Switching Frequency: 200kHz to 3MHz Programmable Soft-Start 6.25mm × 9mm × 3.32mm BGA Package

60V Low IQ, Dual, 2-Phase Synchronous Step-Down DC/DC Controller Features: Wide VIN Range: 4.5V to 60V (65V Abs Max) Wide Output Voltage Range: 0.8V ≤ VOUT ≤ 99% • VIN Adjustable Gate Drive Level 5V to 10V (OPTI-DRIVE) No External Bootstrap Diodes Required Low Operating IQ: 29μA (One Channel On) Selectable Gate Drive UVLO Thresholds Out-of-Phase Operation Reduces Required Input Capacitance and Power Supply Induced Noise Phase-Lockable Frequency: 75kHz to 850kHz Selectable Continuous, Pulse Skipping or Low Ripple Burst Mode® Operation at Light Loads Selectable Current Limit (LTC3892/LTC3892-2) Very Low Dropout Operation: 99% Duty Cycle Power Good Output Voltage Monitors (LTC3892/LTC3892-2) Low Shutdown IQ: 3.6μA Small 32-Lead 5mm × 5mm QFN Package (LTC3892/LTC3892-2) or TSSOP Package (LTC3892-1)

Dual Channel 2A, 42V,Synchronous Step-Down Silent Switcher 2with 6.2A Quiescent Current Features: Silent Switcher®2 Architecture: Ultralow EMI on Any PCB Eliminates PCB Layout Sensitivity Internal Bypass Capacitors Reduce Radiated EMI Optional Spread Spectrum Modulation 2A DC from Each Channel Simultaneously Up to 3A on Either Channel Ultralow Quiescent Current Burst Mode® Operation: 6.2μA IQ Regulating 12VIN to 5VOUT1 and 3.3VOUT2 Output Ripple < 10mVP–P Optional External VC Pin: Fast Transient Response Forced Continuous Mode High Efficiency at High Frequency 94.1% Efficiency at 1A, 5VOUT from 12VIN at 2MHz Pin-Selectable Fixed Output Voltages: 5V, 3.3V, 1.8V Fast Minimum Switch-On Time: 30ns Wide Input Voltage Range: 3.0V to 42V Adjustable and Synchronizable: 300kHz to 3MHz Fixed Output Pin Strap Options Internal 2MHz fSW with Fast Internal Compensation Small 4mm × 3mm 20-Pin LQFN Package AEC-Q100 Qualified for Automotive Applications

High Voltage Buck-Boost Battery ChargeController with Maximum Power PointTracking (MPPT) and I2C Features: VIN Range: 6V to 80V VBAT Range: 1.3V to 80V Single Inductor Allows VIN Above, Below, or Equal to VBAT Automatic MPPT for Solar Powered Charging Automatic Temperature Compensation I2C Telemetry and Configuration Internal EEPROM for Configuration Storage Operation from Solar Panel or DC Supply Four Integrated Feedback Loops Synchronizable Fixed Frequency: 100kHz to 400kHz 64-Lead (7mm × 11mm × 0.75mm) QFN Package

Current, Voltage, and Charge Monitor forHigh Voltage Battery Packs Features: Measures Battery Stack Voltage, Current and Power Indicates Accumulated Battery Charge and Energy 20-Bit Current Measurement with <1μV Offset Built-In Isolated isoSPI™ or SPI Interface LTC68xx/ADBMS68xx Compatible, Supports Synchronous Measurements with Cell Monitors Up to 12 Buffered Voltage Measurement Inputs Up to 5 GPIOs, Configurable to Drive Ground, Supply or Toggling at 400kHz High or Low Side Current Sense 0.3% Current and Voltage Accuracy 1% Energy and Charge Accuracy True Average ADCs I2C EEPROM Interface to Store Board Calibration Factors Threshold Registers for all Measured Quantities Engineered for ISO26262 Compliant Systems Open Wire Detection on Input Pins Available in 48-Lead LQFP Package AEC-Q100 Qualified for Automotive Applications

Fast 60V Protected High Side NMOS Static Switch Driver Features: Wide Operating VIN: 3.5V to 60V 1Ω Pull-Down, 2.2Ω Pull-Up for Fast Turn-On and Turn-Off Times with 35ns Propagation Delays Internal Charge Pump for 100% Duty Cycle Short-Circuit Protected Adjustable Current Trip Threshold Current Monitor Output Automatic Restart Timer Open-Drain Fault Flag Adjustable Turn-On Slew Rate Gate Driver Supply from 3.5V to 15V Adjustable VIN Undervoltage and Overvoltage Lockouts Adjustable Driver Supply VCC Undervoltage Lockout Low Shutdown Current: 1µA CMOS Compatible Input Thermally Enhanced, High Voltage Capable 16-Lead MSOP Package AEC-Q100 Qualified for Automotive Applications

60V, 1.5A LED Driver with Internal Exponential Scale Dimming Features: Operates in Boost, SEPIC, Buck Mode and Buck-Boost Mode 128:1 Internal Exponential Scale PWM Dimming Wide Input Voltage Range (3V to 60V) 1.5A, 60V Internal Switch 20000:1 External PWM Dimming at 100Hz ±2% LED Current and Output Voltage Regulation PMOS Switch Driver for PWM Dimming LED Short/Open Protection and Indication Constant Voltage and Constant Current Regulation Adjustable 300kHz to 2MHz Switching Frequency Adjustable 100Hz to 1kHz PWM Generator Frequency Internal Spread Spectrum Frequency Modulation Easy Synchronization to External Clock Programmable VIN UVLO with Hysteresis Available in 16-Lead MSOP Package

Single Channel Transimpedance Amplifier with Output Multiplexing Features: 220MHz –3dB Bandwidth with 2pF Input Capacitance Single-Ended Output 74kΩ Transimpedance Gain 4.8pA/√Hz Input Current Noise Density at 200MHz (2pF) 64nARMS Integrated Input Current Noise Over 200MHz (2pF) Linear Input Range 0µA to 30µA Overload Current > ±400mA Peak Fast Overload Recovery: 1mA in 10ns Fast Output MUXing: <50ns Single 5V Supply 90mW Power Dissipation 2VP-P Output Swing on 100Ω Load 3mm × 3mm, 16-Lead QFN Package Output MUX Combines Multiple LTC6560 Devices AEC-Q100 Qualified for Automotive Applications

Low IQ Boost/SEPIC/Inverting Converter with 1.5A, 150V Switch Features: Wide Input Voltage Range: 2.8V to 60V Ultralow Quiescent Current and Low Ripple Burst Mode® Operation: IQ = 9µA 1.5A, 150V Power Switch Positive or Negative Output Voltage Programming with a Single Feedback Pin Programmable Frequency (100kHz to 500kHz) Synchronizable to an External Clock Spread Spectrum Frequency Modulation for Low EMI BIAS Pin for Higher Efficiency Programmable Undervoltage Lockout (UVLO) Thermally Enhanced 16-lead MSOP Package AEC-Q100 Qualified for Automotive Applications