The ADP3338 is a member of the ADP330x family ofprecision low dropout anyCAP® voltage regulators. The ADP3338 operates with an input voltage range of +2.7 V to +8 V and delivers a load current up to 1 A. The ADP3338 stands out from the conventional LDOs with a novel architecture and an enhanced process that enables it to offer performance advantages and higher output currentthan its competition. Its patented design requires only a 1.0 µF output capacitor for stability. This device is insensitive to output capacitor Equivalent Series Resistance (ESR), and is stable with any good quality capacitor, including ceramic (MLCC) types for space-restricted applications.The ADP3338 achieves exceptional accuracy of ±0.9% at room temperature and ±1.8% over temperature, line and load variations. The dropout voltage of the ADP3338 is only 200 mV (typical) at 1 A. This device also includes a safety current limit and thermal overload protection. The ADP3338 has ultralow quiescent current 130 µA (typ) in light load situations.APPLICATIONS  Notebook, palmtop computers SCSI terminators Battery-powered systems Bar code scanners Camcorders, cameras Home entertainment systems Networking systems DSP/ASIC supplies

The ADuC816 is a complete smart transducer front-end, integratingtwo high-resolution sigma-delta ADCs, an 8-bit MCU,and program/data Flash/EE Memory on a single chip. This lowpower device accepts low-level signals directly from a transducer.The two independent ADCs (Primary and Auxiliary) include atemperature sensor and a PGA (allowing direct measurement oflow-level signals). The ADCs with on-chip digital filtering areintended for the measurement of wide dynamic range, lowfrequency signals, such as those in weigh scale, strain gauge,pressure transducer, or temperature measurement applications.The ADC output data rates are programmable and the ADCoutput resolution will vary with the programmed gain andoutput rate.The device operates from a 32 kHz crystal with an on-chip PLLgenerating a high-frequency clock of 12.58 MHz. This clock is,in turn, routed through a programmable clock divider from whichthe MCU core clock operating frequency is generated. Themicrocontroller core is an 8052 and therefore 8051-instructionset-compatible.The microcontroller core machine cycle consistsof 12 core clock periods of the selected core operating frequency.8 Kbytes of nonvolatile Flash/EE program memory are providedon-chip. 640 bytes of nonvolatile Flash/EE data memory and256 bytes RAM are also integrated on-chip.The ADuC816 also incorporates additional analog functionalitywith a 12-bit DAC, current sources, power supply monitor,and a bandgap reference. On-chip digital peripherals include awatchdog timer, time interval counter, three timers/counters,and three serial I/O ports (SPI, UART, and I2C-compatible).On-chip factory firmware supports in-circuit serial download anddebug modes (via UART), as well as single-pin emulation modevia the EA pin.The part operates from a single 3 V or 5 V supply. When operatingfrom 3 V supplies, the power dissipation for the part is below10 mW. The ADuC816 is housed in a 52-lead MQFP package.The part operates from a single 3 V or 5 V supply. When operatingfrom 3 V supplies, the power dissipation for the part is below10 mW. The ADuC816 is housed in 52-lead MQFP and 56-leadLFCSP packages.Applications Intelligent Sensors (IEEE1451.2-Compatible) Weigh Scales Portable Instrumentation Pressure Transducers 4–20 mA Transmitters

The ADuC841/ADuC842/ADuC843 are complete smart transducer front ends, that integrates a high performance self-calibrating multichannel ADC, a dual DAC, and an optimized single-cycle 20 MHz 8-bit MCU (8051 instruction set compatible)on a single chip.The ADuC841 and ADuC842 are identical with the exception of the clock oscillator circuit; the ADuC841 is clocked directly from an external crystal up to 20 MHz whereas the ADuC842 uses a 32 kHz crystal with an on-chip PLL generating a programmable core clock up to 16.78 MHz.The ADuC843 is identical to the ADuC842 except that the ADuC843 has no analog DAC outputs.The microcontroller is an optimized 8052 core offering up to 20 MIPS peak performance. Three different memory options are available offering up to 62 kBytes of nonvolatile Flash/EE program memory. Four kBytes of nonvolatile Flash/EE data memory, 256 bytes RAM, and 2 kBytes of extended RAM are also integrated on-chip. The parts also incorporate additional analog functionality with two 12-bit DACs, power supply monitor, and a band gap reference. On-chip digital peripherals include two 16-bit Σ-Δ. DACs, a dual output 16-bit PWM, a watchdog timer, a time interval counter, three timers/counters, and three serial I/O ports (SPI, I2C, and UART).On the ADuC812 and the ADuC832, the I2C and SPI interfaces share some of the same pins. For backwards compatibility, this is also the case for the ADuC841/ADuC842/ADuC843.However, there is also the option to allow SPI operate separately on P3.3, P3.4, and P3.5, while I2C uses the standard pins. The I2C interface has also been enhanced to offer repeated start, general call, and quad addressing.On-chip factory firmware supports in-circuit serial download and debug modes (via UART) as well as single-pin emulation mode via the EA pin..Applications Optical networking—laser power control Base station systems Precision instrumentation, smart sensors Transient capture systems DAS and communications systems

The DAC08 series of 8-bit monolithic digital-to-analog convertersprovide very high speed performance coupled with low costand outstanding applications flexibility.Advanced circuit design achieves 85 ns settling times with verylow glitch energy and at low power consumption. Monotonicmultiplying performance is attained over a wide 20 to 1 referencecurrent range. Matching to within 1 LSB between reference andfull-scale currents eliminates the need for full-scale trimming inmost applications.Direct interface to all popular logic families with full noiseimmunity is provided by the high swing, adjustable thresholdlogic input.High voltage compliance complementary current outputs areprovided, increasing versatility and enabling differential operationto effectively double the peak-to-peak output swing. In manyapplications, the outputs can be directly converted to voltagewithout the need for an external op amp. All DAC08 series modelsguarantee full 8-bit monotonicity, and nonlinearities as tight as±0.1% over the entire operating temperature range are available.Device performance is essentially unchanged over the ±4.5 V to±18 V power supply range, with 33 mW power consumptionattainable at ±5 V supplies.The compact size and low power consumption make the DAC08attractive for portable and military/aerospace applications;devices processed to MIL-STD-883, Level B are available.DAC08 applications include 8-bit, 1 µs A/D converters, servomotor and pen drivers, waveform generators, audio encodersand attenuators, analog meter drivers, programmable powersupplies, LCD display drivers, high speed modems, and otherapplications where low cost, high speed, and completeinput/output versatility are required.

The LTC2801/LTC2802/LTC2803/LTC2804 are single and dual RS-232 transceivers in narrow SSOP and chip-scale DFN packages. All operate over a supply range of 1.8V to 5.5V, which permits operation directly from two alkaline, NiCd or NiMH cells. An integrated DC-to-DC converter generates power supplies for driving RS-232 levels. A logic supply pin allows easy interfacing with different logic levels independent of the DC-DC supply.These parts are compatible with the TIA/EIA-232-F standard. Driver outputs are protected from overload and can be shorted to ground or up to ±15V without damage. To extend battery life, receivers can be kept active, operating at reduced speed, with only 15μA current. In shutdown mode, current is further reduced to 1μA. Part Number Driver & Receivers Max Data Rate Modes Package LTC2801 1 + 1 0.25Mbps SD, RA, DD, AO DFN-12 LTC2802 1 + 1 1Mbps SD, RA, DD, AO DFN - 12 LTC2803 2 + 2 0.25Mbps SD, RA, DD, AO DFN-16 LTC2803-1 2 + 2 0.25Mbps SD, AO SSOP-16 LTC2804 2 + 2 1Mbps SD, RA, DD, AO DFN-16 LTC2804-1 2 + 2 1Mbps SD, AO SSOP-16 Applications Battery-Powered Systems Computers and Consumer Electronics Diagnostic Ports

The LTC2607/LTC2617/LTC2627 are dual 16-, 14- and 12-bit, 2.7V to 5.5V rail-to-rail voltage output DACs in a 12-lead DFN package. They have built-in high performance output buffers and are guaranteed monotonic.These parts establish new board-density benchmarks for 16- and 14-bit DACs and advance performance standards for output drive and load regulation in single-supply, voltage-output DACs.The parts use a 2-wire, I2C compatible serial interface. The LTC2607/LTC2617/LTC2627 operate in both the standard mode (clock rate of 100kHz) and the fast mode (clock rate of 400kHz). An asynchronous DAC update pin (LDAC) is also included.The LTC2607/LTC2617/LTC2627 incorporate a power-on reset circuit. During power-up, the voltage outputs rise less than 10mV above zero scale; and after power-up, they stay at zero scale until a valid write and update take place. The power-on reset circuit resets the LTC2607-1/LTC2617-1/ LTC2627-1 to mid-scale. The voltage outputs stay at midscale until a valid write and update takes place.Applications Mobile Communications Process Control and Industrial Automation Instrumentation Automatic Test Equipment

The LTC2484 combines a 24-bit No Latency ΔΣ™ analog-to-digital converter with patented Easy Drive™ technology. The patented sampling scheme eliminates dynamic input current errors and the shortcomings of on-chip buffering through automatic cancellation of differential input current. This allows large external source impedances and input signals with rail-to-rail input range to be directly digitized while maintaining exceptional DC accuracy.The LTC2484 includes an on-chip oscillator. The LTC2484 can be configured to reject line frequencies. 50Hz, 60Hz or simultaneous 50Hz/60Hz line frequency rejection can be selected as well as a 2× speed-up mode.The LTC2484 allows a wide common mode input range (0V to VCC) independent of the reference voltage. The reference can be as low as 100mV or can be tied directly to VCC. The LTC2484 includes an on-chip trimmed oscillator, eliminating the need for external crystals or oscillators. Absolute accuracy and low drift are automatically maintained through continuous, transparent, offset and full-scale calibration.Applications Direct Sensor Digitizer Weight Scales Direct Temperature Measurement Strain Gauge Transducers Instrumentation Industrial Process Control DVMs and Meters

The ADA4084-1 (single), ADA4084-2 (dual), and ADA4084-4 (quad) are single-supply, 10 MHz bandwidth amplifiers featuring rail-to-rail inputs and outputs. They are guaranteed to operate from +3 V to +30 V (or ±1.5 V to ±15 V).These amplifiers are well suited for single-supply applications requiring both ac and precision dc performance. The combination of wide bandwidth, low noise, and precision makes the ADA4084-1/ADA4084-2/ADA4084-4 useful in a wide variety of applications, including filters and instrumentation.Other applications for these amplifiers include portable telecommunications equipment, power supply control and protection, and use as amplifiers or buffers for transducers with wide output ranges. Sensors requiring a rail-to-rail input amplifier include Hall effect, piezoelectric, and resistive transducers.The ability to swing rail to rail at both the input and output enables designers to build multistage filters in single-supply systems and to maintain high signal-to-noise ratios.The ADA4084-1/ADA4084-2/ADA4084-4 are specified over the industrial temperature range of −40°C to +125°C.The single ADA4084-1 is available in the 5-lead SOT-23 and 8-lead SOIC; the dual ADA4084-2 is available in the 8-lead SOIC, 8-lead MSOP, and 8-lead LFCSP surface-mount packages; and the ADA4084-4 is offered in the 14-lead TSSOP and 16-lead LFCSP.The ADA4084-1/ADA4084-2/ADA4084-4 are members of a growing series of high voltage, low noise op amps offered by Analog Devices, Inc.Applications Battery-powered instrumentation High-side and low-side sensing Power supply control and protection Telecommunications Digital-to-analog converter (DAC) output amplifiers Analog-to-digital converter (ADC) input buffers

The ADA4666-2 is a dual, rail-to-rail input/output amplifier optimized for low power, high bandwidth, and wide operating supply voltage range applications.The ADA4666-2 performance is guaranteed at 3.0 V, 10 V, and 18 V power supply voltages. It is an excellent selection for applications that use single-ended supplies of 3.3 V, 5 V, 10 V, 12 V, and 15 V, and dual supplies of ±2.5 V, ±3.3 V, and ±5 V.The ADA4666-2 is specified over the extended industrial temperature range (−40°C to +125°C) and is available in 8-lead MSOP and 8-lead LFCSP (3 mm × 3 mm) packages. Current monitors Active filters Portable medical equipment Buffer/level shifting High impedance sensor interface Battery powered instrumentation

The ADA4896-2/ADA4897-1 are unity gain stable, low noise, rail-to-rail output, high speed voltage feedback amplifiers that have a quiescent current of 3 mA. With the 1/f noise of 2.4 nV/√Hz at 10 Hz and a spurious-free dynamic range of −80 dBc at 2 MHz, the ADA4896-2/ADA4897-1 are an ideal solution in a variety of applications, including ultrasound, low noise preamplifiers, and drivers of high performance ADCs. The Analog Devices, Inc., proprietary next generation SiGe bipolar process and innovative architecture enable such high performance amplifiers.TheADA4896-2/ADA4897-1 have 230 MHz bandwidth, 120 V/μs slew rate, and settle to 0.1% in 45 ns. With a wide supply voltage range (3 V to 10 V), the ADA4896-2/ADA4897-1 are ideal candidates for systems that require high dynamic range, precision, and high speed.The ADA4896-2 is available in 8-lead LFCSP and 8-lead MSOP packages. The ADA4897-1 is available in 8-lead SOIC and 6-lead SOT-23 packages. Both the ADA4896-2 and ADA4897-1 work over the extended industrial temperature range of −40°C to +125°C.Applications Low noise preamplifier Ultrasound amplifiers PLL loop filters High performance ADC drivers DAC buffers