RF Vector Modulator 1.5 GHz TO 2.4 GHz Features: Cartesian amplitude and phase modulation 1.5 GHz to 2.4 GHz frequency range Continuous magnitude control of −4.5 dB to −34.5 dB Continuous phase control of 0° to 360° Output third-order intercept 17.5 dBm Output 1 dB compression point 8.5 dBm Output noise floor −150.5 dBm/Hz at full gain Adjustable modulation bandwidth up to 230 MHz Fast output power disable 4.75 V to 5.25 V single-supply voltage 

60 MHz, 2000 V/s, Monolithic Op Amp with Quad Low Noise Features: Wide bandwidth 60 MHz at gain of −1  33 MHz at gain of −10  Slew rate: 2000 V/μs  20 MHz full power bandwidth, 20 V p-p, RL = 500 Ω  Fast settling: 100 ns to 0.1% (10 V step) Differential gain error: 0.03% at 4.4 MHz  Differential phase error: 0.16° at 4.4 MHz  Low offset voltage: 150 μV maximum (B Grade) Low quiescent current: 6.5 mA  Available in tape and reel in accordance with EIA-481-A standard

Digitally Programmable Sensor Signal Amplifier with EMI Filters Features: EMI filters at input pins Specified from −40°C to +140°C Low offset voltage: 10 μV maximum Low input offset voltage drift: 65 nV/°C maximum High CMRR: 94 dB minimum Digitally programmable gain and output offset voltage Programmable output clamp voltage Open and short wire fault detection Low-pass filtering Single-wire serial interface Stable with any capacitive load SOIC_N and LFCSP_VQ packages 4.5 V to 5.5 V operation

8-Channel, Low Noise, Low Power, 24-Bit, Sigma-Delta ADC with PGA and Reference Features: 3 power modes RMS noise Low power: 24 nV rms at 1.17 SPS, gain = 128 (255 µA typical) Mid power: 20 nV rms at 2.34 SPS, gain = 128 (355 µA typical) Full power: 23 nV rms at 9.4 SPS, gain = 128 (930 µA typical) Up to 22 noise free bits in all power modes (gain = 1) Output data rate Full power: 9.38 SPS to 19,200 SPS Mid power: 2.34 SPS to 4800 SPS Low power: 1.17 SPS to 2400 SPS Rail-to-rail analog inputs for gains > 1 Simultaneous 50 Hz/60 Hz rejection at 25 SPS (single cycle settling) Diagnostic functions (which aid safe integrity level (SIL) certification) Crosspoint multiplexed analog inputs 8 differential/15 pseudo differential inputs See data sheet for additional features

4-Channel, Low Noise, Low Power, 24-Bit, Sigma-Delta ADC with PGA and Reference Features: Three power modes RMS noise Low power: 24 nV rms at 1.17 SPS, gain = 128 (255 μA typical) Mid power: 20 nV rms at 2.34 SPS, gain = 128 (355 μA typical) Full power: 23 nV rms at 9.4 SPS, gain = 128 (930 μA typical) Up to 22 noise free bits in all power modes (gain = 1) Output data rate Full power: 9.38 SPS to 19,200 SPS Mid power: 2.34 SPS to 4800 SPS Low power: 1.17 SPS to 2400 SPS Rail-to-rail analog inputs for gains > 1 Simultaneous 50 Hz/60 Hz rejection at 25 SPS (single cycle settling) Diagnostic functions (which aid safe integrity level (SIL) certification Crosspoint multiplexed analog inputs 4 differential/7 pseudo differential inputs Programmable gain (1 to 128) Band gap reference with 10 ppm/°C drift maximum (70 μA) Matched programmable excitation currents Internal clock oscillator On-chip bias voltage generator Low-side power switch General-purpose outputs Multiple filter options Internal temperature sensor Self and system calibration Sensor burnout detection Automatic channel sequencer Per channel configuration Power supply: 2.7 V to 3.6 V and ±1.8 V Independent interface power supply Power-down current: 5 μA maximum Temperature range: −40°C to +125°C 32-lead LFCSP/24-lead TSSOP 3-wire or 4-wire serial interface SPI, QSPI, MICROWIRE, and DSP compatible Schmitt trigger on SCLK ESD: 4 kVAD7124-4-EP Supports defense and aerospace applications (AQEC standard) Download AD7124-4-EP Data Sheet (PDF) Full military temperature range: −55°C to +125°C Controlled manufacturing baseline 1 assembly/test site 1 fabrication site Product change notification Qualification data available on request V62/19614

Precision 1.7 g, 5 g, 18 g Dual-Axis iMEMS Accelerometer Features: High performance dual-axis accelerometer on a single IC chip 5 mm × 5 mm × 2 mm LCC package 1 mg resolution at 60 Hz Low power: 700 µA at VS = 5 V (typical) High zero g bias stability High sensitivity accuracy –40°C to +125°C temperature range X and Y axes aligned to within 0.1° (typical) BW adjustment with a single capacitor Single-supply operation 3500 g shock survival RoHS-compliant Compatible with Sn/Pb- and Pb-free solder processes

Single-Supply, Multichannel, 125 kSPS, 24-Bit, Sigma-Delta ADC with 10 V Inputs Features:24-bit ADC with integrated AFEFast and flexible output rate: 2.5 SPS to 125 kSPSChannel scan data rate of 24,845 SPS per channel (40.25 s settling)85 dB common mode rejection of 50 Hz and 60 Hz at 20 SPS per channel10 V inputs, either 8 differential or 16 single-endedVIN pin absolute maximum rating 65 VAbsolute input pin voltage up to 20 VMinimum 1 M impedanceOn-chip 2.5 V reference0.12% initial accuracy at 25C, 5 ppm/C (typical) driftInternal or external clockPower suppliesAVDD = 4.5 V to 5.5 VIOVDD = 2 V to 5.5 VTotal current consumption AVDD + IOVDD (IDD) = 10.4 mATemperature range: 40C to +105C3-wire or 4-wire serial digital interface (Schmitt trigger on SCLK)SPI, QSPI, MICROWIRE, and DSP compatible

Dual 12-Bit nanoDAC+ with 2 ppm/C Reference, I2C Interface Features: Low drift 2.5 V reference: 2 ppm/°C typical Tiny package: 3 mm × 3 mm, 16-lead LFCSP Total unadjusted error (TUE): ±0.1% of full-scale range (FSR) maximum Offset error: ±1.5 mV maximum Gain error: ±0.1% of FSR maximum High drive capability: 20 mA, 0.5 V from supply rails User selectable gain of 1 or 2 (GAIN pin) Reset to zero scale or midscale (RSTSEL pin) 1.8 V logic compatibility Low glitch: 0.5 nV-sec 400 kHz I2C-compatible serial interface Low power: 3.3 mW at 3 V 2.7 V to 5.5 V power supply −40°C to +105°C temperature range

Single-Channel, 16-Bit Current and Voltage Output DAC with Dynamic Power Control and HART Connectivity Features: 16-bit resolution and monotonicity DPC for thermal management Current/voltage output available on a single terminal Current output ranges: 0 mA to 20 mA, 4 mA to 20 mA, 0 mA to 24 mA, ±20 mA, ±24 mA, −1 mA to +22 mA Voltage output ranges (with 20% overrange): 0 V to 5 V, 0 V to 10 V, ±5 V, and ±10 V User-programmable offset and gain Advanced on-chip diagnostics, including a 12-bit ADC On-chip reference Robust architecture, including output fault protection EMC test standards: IEC 61000-4-6 conducted immunity (10 V, Class A) IEC 61000-4-3 radiated immunity (20 V/m, Class A) IEC 61000-4-2 ESD (±6 kV contact, Class B) IEC 61000-4-4 electrical fast transient (EFT) (±4 kV, Class B) IEC 61000-4-5 surge (±4 kV, Class B) 32-lead, 5 mm × 5 mm LFCSP −40°C to +115°C temperature range

High Precision, Impedance & Electrochemical Front End Features: Analog input 16-bit ADC with both 800 kSPS and 1.6 MSPS options Voltage, current, and impedance measurement capability Internal and external current and voltage channels Ultralow leakage switch matrix and input mux Input buffers and programmable gain amplifier Voltage DACs Dual output voltage DAC with an output range of 0.2 V to 2.4 V 12-bit VBIAS0 output to bias potentiostat 6-bit VZERO0 output to bias TIA Ultra low power: 1 µA 1 high speed, 12-bit DAC Output range to sensor: ±607 mV Programmable gain amplifier on output with gain settings of 2 and 0.05 Amplifiers, accelerators, and references 1 low power, low noise potentiostat amplifier suitable for potentiostat bias in electrochemical sensing 1 low noise, low power TIA, suitable for measuring sensor current output 50 pA to 3 mA range Programmable load and gain resistors for sensor output Analog hardware accelerators Digital waveform generator Receive filters Complex impedance measurement (DFT) engine 1 high speed TIA to handle wide bandwidth input signals from 0.015 Hz up to 200 kHz Digital waveform generator for generation of sinusoid and trapezoid waveforms 2.5 V and 1.82 V internal reference voltage sources System level power savings Fast power-up and power-down analog blocks for duty cycling Programmable AFE sequencer to minimize workload of host controller 6 kB SRAM to preprogram AFE sequences Ultra low power potentiostat channel: 6.5 µAof current consumption when powered on and all other blocks in hibernate mode Smart sensor synchronization and data collection Cycle accurate control of sensor measurement Sequencer controlled GPIOs On-chip peripherals SPI serial input/output Wake-up timer Interrupt controller Power 2.8 V to 3.6 V supply 1.82 V input/output compliant Power-on reset Hibernate mode with low power DAC and potentiostat amplifier powered up to maintain sensor bias Package and temperature range 3.6 mm × 4.2 mm, 56-ball WLCSP 7 mm × 7 mm, 48-lead LFCSP Fully specified for operating temperature range of −40°C to +85°C AD5940 and AD5941 fully specified for operating temperature range of −40°C to +85°C AD5941W fully specified for operating temperature range of −40°C to +105°C AEC-Q100 qualified for automotive applications