The AD706 is a dual, low power, bipolar op amp that has thelow input bias current of a JFET amplifier, but which offers asignificantly lower IB drift over temperature. It utilizes superbetabipolar input transistors to achieve picoampere input bias currentlevels (similar to FET input amplifiers at room temperature),while its IB typically only increases by 5 at 125°C (unlike aJFET amp, for which IB doubles every 10°C for a 1000×increase at 125°C). The AD706 also achieves the microvoltoffset voltage and low noise characteristics of a precision bipolarinput amplifier.Since it has < 200 pA of bias current, the AD706 does notrequire the commonly used “balancing” resistor. Furthermore,the current noise is only 50 fA/√Hz, which makes this amplifierusable with very high source impedances. At 600 A max supplycurrent (per amplifier), the AD706 is well suited for today’shigh density boards.The AD706 is an excellent choice for use in low frequencyactive filters in 12-bit and 14-bit data acquisition systems, inprecision instrumentation, and as a high quality integrator. TheAD706 is internally compensated for unity gain and is availablein five performance grades. The AD706J is rated over thecommercial temperature range of 0°C to +70°C. The AD706A israted for the extended industrial temperature range of −40°Cto +85°C.The AD706 is offered in two varieties of an 8-lead package:PDIP and surface-mount (SOIC).PRODUCT HIGHLIGHTS The AD706 is a dual low drift op amp that offers JFET level input bias currents, yet has the low IB drift of a bipolar amplifier. It may be used in circuits using dual op amps such as the LT1024. The AD706 provides both low drift and high dc precision. The AD706 can be used in applications where a chopper amplifier would normally be required but without the chopper’s inherent noise.APPLICATIONS Low Frequency Active Filters Precision Instrumentation Precision Integrators

The AD7237A / AD7247A is an enhanced version of the industry standard AD7237 / AD7247. Improvements include operation from 12 V to 15 V supplies, faster interface times and better reference variations with VDD . Additional features include faster settling times.The AD7237A / AD7247A is a complete, dual, 12-bit, voltage output digital-to-analog converter with output amplifiers and Zener voltage reference on a monolithic CMOS chip. No external user trims are required to achieve full specified performance.Both parts are microprocessor compatible, with high speed data latches and interface logic. The AD7247A accepts 12-bit parallel data which is loaded into the respective DAC latch using the WR input and a separate Chip Select input for each DAC. The AD7237A has a double buffered interface structure and an 8-bit wide data bus with data loaded to the respective input latch in two write operations. An asynchronous LDAC signal on the AD7237A updates the DAC latches and analog outputs.A REF OUT/REF IN function is provided which allows either the on-chip 5 V reference or an external reference to be used as a reference voltage for the part. For single supply operation, two output ranges of 0 V to +5 V and 0 V to +10 V are available, while these two ranges plus an additional ±5 V range are available with dual supplies. The output amplifiers are capable of developing +10 V across a 2 k(Ω) load to GND.The AD7237A / AD7247A is fabricated in Linear Compatible CMOS (LC2MOS), an advanced, mixed technology process that combines precision bipolar circuits with low power CMOS logic. Both parts are available in a 24-pin, 0.3' wide plastic and hermetic dual-in-line package (DIP) and are also packaged in a 24-lead small outline (SOIC) package.

The AD7242 / AD7244 is a fast, complete, dual 12-bit/14-bit voltage output D/A converter. It consists of a 12-bit/14-bit DAC, 3 V buried Zener reference, DAC output amplifiers and high speed serial interface logic.Interfacing to both DACs is serial, minimizing pin count and allowing a small package size. Standard control signals allow interfacing to most DSP processors and microcontrollers. Asynchronous control of DAC updating for both DACs is made possible with a separate LDAC input for each DAC.The AD7242 / AD7244 operates from ±5 V power supplies, providing an analog output range of ±3 V. A REF OUT/REF IN function allows the DACs to be driven from the on-chip 3 V reference or from an external reference source.The AD7242 / AD7244 is fabricated in Linear Compatible CMOS (LC2MOS), an advanced mixed technology process that combines precision bipolar circuits with low power CMOS logic. Both parts are available in a 24-pin, 0.3-inch wide, plastic or hermetic dual-in-line package (DIP) and in a 28-pin, plastic small outline (SOIC) package. The AD7242 and AD7244 are available in the same pinout to allow easy upgrade from 12-bit to 14-bit performance.PRODUCT HIGHLIGHTS Complete, Dual 12-Bit/14-Bit DACs The AD7242 / AD7244 provides the complete function for generating voltages to 12-bit/14-bit resolution. The part features an on-chip reference, output buffer amplifiers and two 12-bit/14-bit D/A converters. High Speed Serial Interface The AD7242 / AD7244 provides a high speed, easy-to-use, serial interface allowing direct interfacing to DSP processors and microcontrollers. A separate serial port is provided for each DAC. Small Package Size The AD7242 / AD7244 is available in a 24-pin DIP and a 28- pin SOIC package offering considerable space saving over comparable solutions.

The AD7470/AD7472 are 10-bit /12-bit high speed, low power, successive-approximation ADCs. The parts operate from a single 2.7 V to 5.25 V power supply and feature throughput rates up to 1.5 MSPS for the 12-bit AD7472 and up to 1.75 MSPS for the 10-bit AD7470. The parts contain a low-noise, wide bandwidth track/hold amplifier which can handleinput frequencies in excess of 20 MHz.The conversion process and data acquisition are controlledusing standard control inputs, allowing easy interfacing tomicroprocessors or DSPs. The input signal is sampled on thefalling edge of CONVST, and conversion is also initiated atthis point. BUSY goes high at the start of conversion andgoes low 531.66 ns after falling edge of CONVST (AD7472with a clock frequency of 26 MHz) to indicate that the conversionis complete. There are no pipeline delays associatedwith the parts. The conversion result is accessed via standardCS and RD signals over a high speed parallel interface.The AD7470/AD7472 use advanced design techniques toachieve very low power dissipation at high throughput rates. With3 V supplies and 1.5 MSPS throughput rates, the AD7470typically consumes, on average, just 1.1 mA. With 5 V suppliesand 1.75 MSPS, the average current consumption is typically1.6 mA. The part also offers flexible power/throughput ratemanagement. Operating the AD7470 with 3 V supplies and500 kSPS throughput reduces the current consumption to 713 μA.At 5 V supplies and 500 kSPS, the part consumes 944 μA.It is also possible to operate the parts in an auto sleep mode,where the part wakes up to do a conversion and automaticallyenters sleep mode at the end of conversion. This method allowsvery low power dissipation numbers at lower throughput rates.In this mode, the AD7472 can be operated with 3 V supplies at100 kSPS, and consume an average current of just 124 μA. At5 V supplies and 100 kSPS, the average current consumption is171 μA.The analog input range for the part is 0 V to REF IN. The 2.5 Vreference is applied externally to the REF IN pin. The conversionrate is determined by the externally-applied clock.ol { margin-top:0px; margin-right:0px; margin-bottom:0px; margin-left:25px; padding-top:0px; padding-right:0px; padding-bottom:10px; padding-left:0px;}li { padding-top:0px; padding-right:0px; padding-bottom:5px; padding-left:0px; margin-top:0px; margin-right:0px; margin-bottom:0px; margin-left:0px;}Product HighlightsHigh Throughput with Low Power Consumption. TheAD7470 offers 1.75 MSPS throughput and the AD7472offers 1.5 MSPS throughput rates with 4 mW powerconsumption.Flexible Power/Throughput Rate Management. The conversionrate is determined by an externally-applied clock allowingthe power to be reduced as the conversion rate is reduced.The part also features an auto sleep mode to maximize powerefficiency at lower throughput rates.No Pipeline Delay. The part features a standard successiveapproximation ADC with accurate control of the samplinginstant via a CONVST input and once off conversion control.

The AD7820 is a high speed, microprocessor-compatible 8-bit ADC which uses a half-flash conversion technique to achieve a conversion time of 1.36 µs. The converter has a 0 V to +5 V analog input voltage range with a single +5 V supply.The half-flash technique consists of 31 comparators, a most significant 4-bit ADC and a least significant 4-bit ADC. The input to the AD7820 is tracked and held by the input sampling circuitry, eliminating the need for an external sample-and-hold for signals with slew rates less than 100 mV/µs.The part is designed for ease of microprocessor interface with the AD7820 appearing as a memory location or I/O port without the need for external interfacing logic. All digital outputs use latched, three-state output buffer circuitry to allow direct connection to a microprocessor data bus or system input port. A non-three state overflow output is also provided to allow cascading of devices to give higher resolution.

The AD7845 is the industry's first 4-quadrant multiplying D/A converter with an on-chip amplifier. It is fabricated on the LC2MOS process, which allows precision linear components and digital circuitry to be implemented on the same chip.The 12 data inputs drive latches which are controlled by standard CS and WR signals, making microprocessor interfacing simple. For stand-alone operation, the CS and WR inputs can be tied to ground, making all latches transparent. All digital inputs are TTL and 5 V CMOS compatible.The output amplifier can supply ±10 V into a 2k(ohm) load. It is internally compensated, and its input offset voltage is low due to laser trimming at wafer level. For normal operation, RFB is tied to VOUT, but the user may alternatively choose RA, RB or RC to scale the output voltage range.

The AD7943, AD7945 and AD7948 are fast 12-bit multiplying DACs that operate from a single +5 V supply (Normal Mode) and a single +3.3 V to +5 V supply (Biased Mode). The AD7943 has a serial interface, the AD7945 has a 12-bit parallel interface, and the AD7948 has an 8-bit byte interface. They will replace the industry-standard AD7543, AD7545 and AD7548 in many applications, and they offer superior speed and power consumption performance.The AD7943 is available in 16-pin DIP, 16-pin SOP (Small Outline Package) and 20-pin SSOP (Shrink Small Outline Package).The AD7945 is available in 20-pin DIP, 20-pin SOP and 20-pin SSOP.The AD7948 is available in 20-pin DIP, 20-pin SOP and 20-pin SSOP.APPLICATIONS Battery-Powered Instrumentation Laptop Computers Upgrades for All 754x Series DACs (5 V Designs)

The AD795 is a low noise, precision, FET input operational amplifier. It offers both the low voltage noise and low offset drift of a bipolar input op amp and the very low bias current of a FET-input device. The 1014 Ω common-mode impedance insures that input bias current is essentially independent of common-mode voltage and supply voltage variations.The AD795 has both excellent dc performance and a guaranteed and tested maximum input voltage noise. It features 2 pA maximum input bias current and 500 μV maximum offset voltage, along with low supply current of 1.5 mA maximum.Furthermore, the AD795 features a guaranteed low input noise of 3.3 μV P-P (0.1 Hz to 10 Hz) and a 11 nV/√Hz maximum noise level at 10 kHz. The AD795 has a fully specified and tested input offset voltage drift of only 10 μV/°C maximum.The AD795 is useful for many high input impedance, low noise applications. The AD795 is rated over the commercial temperature range of 0°C to +70°C.The AD795 is available in an 8-lead SOIC package.Applications Low noise photodiode preamps CT scanners Precision l-to-V converters

The AD842 is a member of the Analog Devices, Inc. family of wide bandwidth operational amplifiers. This device is fabricated using the Analog Device junction isolated complementary bipolar (CB) process. This process permits a combination of dc precision and wideband ac performance previously unobtainable in a monolithic op amp. In addition to its 80 MHz gain bandwidth product, the AD842 offers extremely fast settling characteristics, typically settling to within 0.01% of final value in less than 100 ns for a 10 V step.The AD842 also offers a low quiescent current of 13 mA, a high output current drive capability (100 mA minimum), a low input voltage noise of 9 nV√Hz, and a low input offset voltage (1.5 mV maximum).The 375 V/μs slew rate of the AD842, along with its 80 MHz gain bandwidth product, ensures excellent performance in video and pulse amplifier applications. This amplifier is ideally suited for use in high frequency signal conditioning circuits and wide bandwidth active filters. The extremely rapid settling time of the AD842 makes this amplifier the preferred choice for data acquisition applications requiring 12-bit accuracy. The AD842 is also appropriate for other applications, such as high speed DAC and ADC buffer amplifiers and other wide bandwidth circuitry.

The AD848 and AD849 are high speed, low power monolithic operational amplifiers. The AD848 is internally compensated so that it is stable for closed loop gains of 5 or greater. The AD849 is fully decompensated and is stable at gains greater than 24. The AD848 and AD849 achieve their combination of fast ac and good dc performance by utilizing Analog Devices' junction isolated complementary bipolar (CB) process. This process enables these op amps to achieve their high speed while only requiring 4.8 mA of current from the power supplies.The AD848 and AD849 are members of Analog Devices' family of high speed op amps. This family includes, among others, the AD847 which is unity gain stable, with a gain bandwidth of 50 MHz. For more demanding applications, the AD840, AD841 and AD842 offer even greater precision and greater output current drive.The AD848 and AD849 have good dc performance. When operating with ±5 V supplies, they offer open loop gains of 13 V/mV (AD848 with a 500 Ohm load) and low input offset voltage of 1 mV maximum. Common-mode rejection is a minimum of 92 dB. Output voltage swing is ±3 V even into loads as low as 150 Ohm.