1kHz-3GHz High Signal Level Active Mixer Features: Broadband RF, LO and IF Operation High Input IP3: >20dBm from 30MHz to 900MHz +17dBm at 1900MHz Typical Conversion Gain: 1dB SSB Noise Figure: 11dB at 900MHz 14dB at 1900MHz Integrated LO Buffer: Insensitive to LO Drive Level Single-Ended or Differential LO Drive High LO-RF Isolation Enable Function 4.5V to 5.25V Supply Voltage Range 4mm x 4mm QFN Package

Dual Smart Battery System Manager Features: SMBus Charger/Selector for Two Smart Batteries* Voltage and Current Accuracy within 0.2% of Value Reported by Battery Simplifies Construction of “Smart Battery System Manager” Includes All SMBus Charger V1.1 Safety Features Supports Autonomous Operation without a Host Allows Both Batteries to Discharge Simultaneously into Single Load with Low Loss (Ideal Diode) SMBus Switching for Dual Batteries with Alarm Monitoring for Charging Battery at All Times Pin Programmable Limits for Maximum Charge Current and Voltage Improve Safety Fast Autonomous Power Path™ Switching (<10µs) Low Loss Simultaneous Charging of Two Batteries >95% Efficient Synchronous Buck Charger AC Adapter Current Limiting* Maximizes Charge Rate SMBus Accelerator Improves SMBus Timing** Available in 48-Lead TSSOP Package

40MHz to 900MHz Quadrature Demodulator Features: RF Input Frequency Range: 40MHz to 900MHz High IIP3: 21dBm at 800MHz High IIP2: 58dBm at 800MHz I/Q Gain Mismatch: 0.3dB Max I/Q Phase Mismatch: 0.7° Noise Figure: 12.4dB at 800MHz Conversion Gain: 3.3dB at 800MHz Baseband Bandwidth: 130MHz Single Ended, 50 Matched 2XLO Input Shutdown Mode 16-Lead QFN (4mm × 4mm) Package with Exposed Pad

IC Multidisplay LED Controller Features: Step-Up/Direct-Connect Fractional Charge Pump Provides Up to 92% Efficiency Up to 400mA Continuous Output Current Independent Current and Dimming Control for 1-6 LED MAIN, 1-4 LED SUB and RGB LED Displays LED Currents Programmable Using 2-Wire I2C™ Serial Interface 1% LED Current Matching Low Noise Constant Frequency Operation* Minimal Component Count Automatic Soft-Start Limits Inrush Current 16 Exponentially Spaced Dimming States Provides 128:1 Brightness Range for MAIN and SUB Displays Up to 4096 Color Combinations for RGB Display Low Operating Current: IVIN = 180µA Tiny, Low Profile 24-Lead (4mm × 4mm × 0.75mm) QFN Package

Precision 1.7 g, 5 g, 18 g Dual-Axis iMEMS Accelerometer Features: High performance dual-axis accelerometer on a single IC chip 5 mm × 5 mm × 2 mm LCC package 1 mg resolution at 60 Hz Low power: 700 µA at VS = 5 V (typical) High zero g bias stability High sensitivity accuracy –40°C to +125°C temperature range X and Y axes aligned to within 0.1° (typical) BW adjustment with a single capacitor Single-supply operation 3500 g shock survival RoHS-compliant Compatible with Sn/Pb- and Pb-free solder processes

Single Supply, 24-Bit, Sigma-Delta ADC with 10 V and 0 mA to 20 mA Inputs, Open Wire Detection Features: Tested for robustness per: IEC6100-4-2, IEC6100-4-3, IEC6100-4-4, IEC6100-4-5, IEC6100-4-6, CISPR 11 24-bit ADC with integrated analog front end Fast and flexible output rate: 1.25 SPS to 31.25 kSPS Channel scan data rate of 6.21 kSPS per channel (161 μs settling) 16 noise free bits at 1 kSPS per channel 85 dB rejection of 50 Hz and 60 Hz at 20 SPS per channel ±10 V inputs, 4 differential or 8 single-ended Pin absolute maximum rating ±50 V Absolute input pin voltage up to ±20 V ≥1 MΩ impedance ±0.06% accuracy at 25°C Open wire detection 0 mA to 20 mA inputs, 4 single-ended Pin absolute maximum rating ±50 mA Input range from −0.5 mA to +24 mA 60 Ω impedance ±0.08% accuracy at 25°C On-chip 2.5 V reference ±0.12% accuracy at 25°C, ±5 ppm/°C (typical) drift Internal or external clock Power supplies AVDD = 3.0 V to 5.5 V IOVDD = 2 V to 5.5 V Total IDD = 3.9 mA Temperature range: −40°C to +105°C 3-wire or 4-wire serial digital interface (Schmitt trigger on SCLK) SPI, QSPI, MICROWIRE, and DSP compatible

Single-Supply, Multichannel, 125 kSPS, 24-Bit, Sigma-Delta ADC with 10 V Inputs Features:24-bit ADC with integrated AFEFast and flexible output rate: 2.5 SPS to 125 kSPSChannel scan data rate of 24,845 SPS per channel (40.25 s settling)85 dB common mode rejection of 50 Hz and 60 Hz at 20 SPS per channel10 V inputs, either 8 differential or 16 single-endedVIN pin absolute maximum rating 65 VAbsolute input pin voltage up to 20 VMinimum 1 M impedanceOn-chip 2.5 V reference0.12% initial accuracy at 25C, 5 ppm/C (typical) driftInternal or external clockPower suppliesAVDD = 4.5 V to 5.5 VIOVDD = 2 V to 5.5 VTotal current consumption AVDD + IOVDD (IDD) = 10.4 mATemperature range: 40C to +105C3-wire or 4-wire serial digital interface (Schmitt trigger on SCLK)SPI, QSPI, MICROWIRE, and DSP compatible

256 Position SPI/I2C Selectable Digital Potentiometer Features: 256-position End-to-end resistance 5 kΩ, 10 kΩ, 50 kΩ, 100 kΩ Compact MSOP-10 (3 mm × 4.9 mm) package Pin selectable SPI/I2C compatible interface Extra package address decode pin AD0 Full read/write of wiper register Power-on preset to midscale Single supply 2.7 V to 5.5 V Low temperature coefficient 45 ppm/°C Low power, IDD = 8 μA Wide operating temperature −40°C to +125°C SDO output allows multiple device daisy-chaining Evaluation board available

9 GHz to 12 GHz, GaAs, MMIC, I/Q Downconverter Features: Conversion gain: 11 dB (typical) at IFOUT = 100 MHz Image rejection: 25 dB (typical) at IFOUT = 100 MHz LO to RF isolation: 46 dB (typical) LO to IF isolation: 26 dB (typical) IF output frequency: dc to 3.5 GHz 32-lead, 4.9 mm × 4.9 mm ceramic leadless chip carrier

5.6 GHz to 8.6 GHz, GaAs, MMIC, I/Q Downconverter Features: Conversion gain: 13 dB typical Image rejection: 32 dBc typical Input P1dB compression: −6 dBm typical Input IP3: 3 dBm typical, 6.0 GHz to 8.6 GHz Noise figure: 2 dB typical LO to RF isolation: 48 dBm typical LO to IF isolation: 13 dBm typical RF to IF isolation: 10 dBm typical Amplitude balance: 0.2 dB typical Phase balance: −2° typical RF return loss: 10 dB typical LO return loss: 15 dB typical IF return loss: 15 dB typical Exposed paddle, 4 mm × 4 mm, 24-lead, LFCSP