1 MSPS, 12-Bit, Simultaneous Sampling SAR ADC with PGA and Four Comparators Features: Dual simultaneous sampling 12-bit, 2-channel analog-to-digital converter (ADC) True differential analog inputs Programmable gain stage: ×1, ×2, ×3, ×4, ×6, ×8, ×12, ×16, ×24, ×32, ×48, ×64, ×96, ×128 Throughput rate per ADC 1 MSPS for AD7262 500 kSPS for AD7262-5 Analog input impedance: >1 GΩ Wide input bandwidth −3 dB bandwidth: 1.7 MHz at gain = 2 4 on-chip comparators SNR: 73 dB typical at gain = 2, 66 dB typical at gain = 32 Device offset calibration, system gain calibration On-chip reference: 2.5 V −40°C to +105°C operation High speed serial interface SPI/QSPI™/MICROWIRE/DSP compatible 48-lead LFCSP and LQFP

Quad Voltage Monitor and Sequencer Features: Powered from 2.7 V to 5.5 V on the VCC pin Logical core with internal timeouts provides power supply sequencing and fault protection 4 inputs can be programmed to monitor different voltage levels with resistor dividers Monitors 4 supplies via 0.8% accurate comparators 3 open-drain enable outputs Open-drain power-good output (PWRGD) 10-lead MSOP

Low Noise, Low Drift, Low Power, 3-Axis MEMS Accelerometers with Digital Output Features: Hermetic package offers optimal long-term stability 0 g offset vs. temperature (all axes): 0.75 mg/°C maximum Ultralow noise spectral density (all axes): 75 μg/√Hz Low power, VSUPPLY (LDO regulator enabled) Measurement mode: 200 μA Standby mode: 21 μA Digital output features Digital SPI and limited I2C interfaces supported 20-bit ADC Data interpolation routine for synchronous sampling Programmable high- and low-pass digital filters Integrated temperature sensor Voltage range options VSUPPLY with internal regulators: 2.25 V to 3.6 V V1P8ANA, V1P8DIG with internal LDO regulator bypassed: 1.8 V typical ± 10% Operating temperature range: −40°C to +125°C 14-terminal, 6 mm × 5.6 mm × 2.2 mm, LCC package

Low Noise Amplifier SMT, 350 - 550 MHz Features: Noise Figure: ≤1 dB Output IP3: +38 dBm Gain: 17 dB Very Stable Gain vs. Supply & Temp Single Supply: +5V @ 104 mA 50 Ohm Matched Output

InGaP HBT Divide-by-4 SMT, DC - 18 GHz Features: Ultra Low SSB Phase Noise: -150 dBc/Hz Very Wide Bandwidth Output Power: -4 dBm Single DC Supply: +5V 3x3 mm QFN SMT Package

Dual Output Low Noise Amplifier, 0.04 - 0.96 GHz Features: Single-ended or Balanced Output High Output IP3: +27 dBm Low Noise Figure: 3.5 dB Single Positive Supply: +5V 75 Ohm Input

LTC2256-12 series 12 Bit 25M Samples per Second Analog to Digital Converter (ADC) Evaluation Board

Isolated Module DC DC Converter 1 Output 2.5 ~ 12V 440mA 3.1V - 31V Input

Quad, 16-Bit nanoDAC with 5ppm/C On-Chip Reference Features: Low power, smallest pin-compatible, quad nanoDACs  AD5664R: 16 bits AD5644R: 14 bits AD5624R: 12 bits User selectable external or internal reference External reference default On-chip 1.25 V/2.5 V, 5 ppm/°C reference 10-lead MSOP; 10-lead, 3 mm × 3 mm LFCSP_WD; and 12-ball, 1.665 mm × 2.245 mm WLCSP 2.7 V to 5.5 V power supply Guaranteed monotonic by design Power-on reset to zero scale Per channel power-down Serial interface, up to 50 MHz

Encoders, Decoders, Multiplexers & Demultiplexers 2:1 Mux w/half rate clock