Ultrathin Dual 10A or Single 20A Module Regulator with Digital Power System Management Features: Dual, Fast, Analog Loops with Digital Interface for Control and Monitoring Output Voltage Range: 0.5V to 3.6V ±0.5% Maximum DC Output Error Over Temperature 10A DC Typical, 12A Peak Output Current, per Channel ±5% Current Readback Accuracy at 10A Load 400kHz PMBus-Compliant I2C Serial Interface Integrated 16-Bit Σ ADC Supports Telemetry Polling Rates Up to 125Hz Constant Frequency Current Mode Control Parallel and Current Share Multiple Modules All 7-Bit Slave Addresses Supported Drop-In Pin-Compatible to Dual 9A LTM4675 and Dual 13A LTM4676A and Dual 18A LTM4677 16mm × 11.9mm × 1.82mm LGA PackageReadable Data: Input and Output Voltages, Currents, and Temperatures Running Peak Values, Uptime, Faults and Warnings Onboard EEPROM Fault Log Record with ECCWritable Data and Configurable Parameters: Output Voltage, Voltage Sequencing and Margining Digital Soft-Start/Stop Ramp OV/UV/OT, UVLO, Frequency and Phasing

60V Low IQ, Dual, 2-Phase Synchronous Step-Down DC/DC Controller Features: Wide VIN Range: 4.5V to 60V (65V Abs Max) Wide Output Voltage Range: 0.8V ≤ VOUT ≤ 99% • VIN Adjustable Gate Drive Level 5V to 10V (OPTI-DRIVE) No External Bootstrap Diodes Required Low Operating IQ: 29μA (One Channel On) Selectable Gate Drive UVLO Thresholds Out-of-Phase Operation Reduces Required Input Capacitance and Power Supply Induced Noise Phase-Lockable Frequency: 75kHz to 850kHz Selectable Continuous, Pulse Skipping or Low Ripple Burst Mode® Operation at Light Loads Selectable Current Limit (LTC3892/LTC3892-2) Very Low Dropout Operation: 99% Duty Cycle Power Good Output Voltage Monitors (LTC3892/LTC3892-2) Low Shutdown IQ: 3.6μA Small 32-Lead 5mm × 5mm QFN Package (LTC3892/LTC3892-2) or TSSOP Package (LTC3892-1)

2-Channel PMBus Power System Manager Featuring Programmable Power Good Outputs Features: Sequence, Trim, Margin and Supervise Two Power Supplies Manage Faults, Monitor Telemetry PMBus Compliant Command Set Supported by LTpowerPlay® GUI Margin or Trim Supplies to Within 0.25% of Target Monitor Input Current (±1%) and Accumulate Energy Fast OV/UV Supervisors per Channel Coordinate Sequencing and Fault Management Across Multiple ADI PSM Devices Automatic Fault Logging to Internal EEPROM Operate Autonomously Without Additional Software Configurable Power Good Output Pins Accurate Monitoring of Output Voltage, Output Current, Temperature, and Input Voltage and Current 1.8V to 3.3V I2C/SMBus Serial Interface Connect Directly to Regulator IMON Pins Can Be Powered from 3.3V, or 4.5V to 15V Available in 44-Pin 6mm × 7mm QFN Package LTpowerPlay® Configuration and Development Tool

Fast 60V Protected High Side NMOS Static Switch Driver Features: Wide Operating VIN: 3.5V to 60V 1Ω Pull-Down, 2.2Ω Pull-Up for Fast Turn-On and Turn-Off Times with 35ns Propagation Delays Internal Charge Pump for 100% Duty Cycle Short-Circuit Protected Adjustable Current Trip Threshold Current Monitor Output Automatic Restart Timer Open-Drain Fault Flag Adjustable Turn-On Slew Rate Gate Driver Supply from 3.5V to 15V Adjustable VIN Undervoltage and Overvoltage Lockouts Adjustable Driver Supply VCC Undervoltage Lockout Low Shutdown Current: 1µA CMOS Compatible Input Thermally Enhanced, High Voltage Capable 16-Lead MSOP Package AEC-Q100 Qualified for Automotive Applications

20V, 200mA, Ultralow Noise, Ultrahigh PSRR Precision DAC/Reference Buffer Features: Ultralow Wideband Noise: 1.2µVRMS (10Hz to 100kHz) Ultralow 1/f Noise: 0.6µVP-P (0.1Hz to 10Hz) Ultralow Spot Noise: 4nV/√Hz at 1kHz and Above Ultrahigh PSRR: 73dB at 1MHz Ultralow Input Offset: 125µV Output Source Current: 200mA Wide Input Voltage Range: 1.8V to 20V Rail to Rail Output Voltage Range: 0V to 15V Single Capacitor Improves Noise and PSRR Fast Start-Up for VIN Pin FAULT Flag High Bandwidth: 1MHz Low Dropout Voltage: 350mV Programmable Current Limit Precision Enable/UVLO Parallelable for Lower Noise and Higher Current Internal Current Limit with Foldback Minimum Output Capacitor: 4.7µF Ceramic Reverse Supply and Reverse Current Protection Thermal Limit with Hysteresis 10-Lead 3mm × 3mm DFN and 12-Lead MSOP

5.6 GHz to 8.6 GHz, GaAs, MMIC, I/Q Downconverter Features: Conversion gain: 13 dB typical Image rejection: 32 dBc typical Input P1dB compression: −6 dBm typical Input IP3: 3 dBm typical, 6.0 GHz to 8.6 GHz Noise figure: 2 dB typical LO to RF isolation: 48 dBm typical LO to IF isolation: 13 dBm typical RF to IF isolation: 10 dBm typical Amplitude balance: 0.2 dB typical Phase balance: −2° typical RF return loss: 10 dB typical LO return loss: 15 dB typical IF return loss: 15 dB typical Exposed paddle, 4 mm × 4 mm, 24-lead, LFCSP

Quad-Channel, Software Configurable Input and Output Features: Quad-channel software configurable input/output circuit Screw terminals tolerant to ±40 V dc Line protectors to block power from the screw terminals to supplies User configurable modes Voltage input Current input Voltage output Current output Digital input RTD measurement Internal 16-bit, Σ- ADC with optional 50 Hz and 60 Hz rejection 13-bit monotonic DACs Charge pump for true zero voltage output HART-compatible Internal temperature sensor, ±5°C accuracy On-chip diagnostics including open circuit and short-circuit detection SPI-compatible Temperature range: −40°C to +105°C 64-lead LFCSP

High Performance, Multiphase Energy, and Power Quality Measurement IC Features: 7 high performance ADCs 101 dB SNR Wide input voltage range: ±1 V, 707 mV rms FS at gain = 1 Differential inputs ±25 ppm/°C maximum channel drift (including ADC, internal VREF, PGA drift) enabling 10000:1 dynamic input range Class 0.2 metrology with standard external components Power quality measurements Enables implementation of IEC 61000-4-30 Class S VRMS ½, IRMS ½ rms voltage refreshed each half cycle 10 cycle rms/12 cycle rms Dip and swell monitors Line frequency—one per phase Zero crossing, zero-crossing timeout Phase angle measurements Supports CTs and Rogowski coil (di/dt) sensors Multiple range phase/gain compensation for CTs Digital integrator for Rogowski coils Flexible waveform buffer Able to resample waveform to ensure 128 points per line cycle for ease of external harmonic analysis Events, such as dip and swell, can trigger waveform storage Simplifies data collection for IEC 61000-4-7 harmonic analysis Advanced metrology feature set Total and fundamental active power, volt amperes reactive (VAR), volt amperes (VA), watthour, VAR hour, and VA hour Total and fundamental IRMS, VRMS Total harmonic distortion Power factor Supports active energy standards: IEC 62053-21 and IEC 62053-22; EN50470-3; OIML R46; and ANSI C12.20 Supports reactive energy standards: IEC 62053-23, IEC 62053-24 High speed communication port: 20 MHz serial port interface (SPI) Integrated temperature sensor with 12-bit successive approximation register (SAR) ADC ±3°C accuracy from −40°C to +85°C

Energy Metering IC with Autocalibration Features: mSure autocalibration Automatic calibration based on a direct measurement of the full signal path Calibration procedure not requiring a reference meter mSure autocalibration Class 1 meter guaranteed 3 high performance ADCs 88 dB SNR High gain current channel: ±26.04 mV peak, 18.4 mV rms input at highest gain setting Advanced metrology feature set WATT, VAR, VA, Wh, VARh, and VAh Supports active energy standards: IEC 62053-21; IEC 62053-22; EN50470-3; OIML R46; and ANSI C12.20 Supports reactive energy standards: IEC 62053-23 and IEC 62053-24 Current and voltage rms measurement Power quality measurements Operating temperature, industrial range: −40°C to +85°C

9.85 GHz to 20.5 GHz, Wideband, MMIC VCO Features: Wide output frequency range: 9.85 GHz to 20.5 GHz Wide tuning bandwidth Low single sideband phase noise: −83 dBc/Hz at 100 kHz offset No external resonator needed Supply current: 70 mA typical at VCC = 5 V 24-terminal, 3.90 mm × 3.90 mm, ceramic LCC package