The AD8313 is a complete multistage demodulating logarithmic amplifier that can accurately convert an RF signal at its input to an equivalent decibel-scaled value at its dc output. The AD8313 maintains a high degree of log conformance for signal frequencies from 0.1 GHz to 2.5 GHz. Application is straightforward, requiring only a single supply of 2.7 V to 5.5 V and the addition of a suitable input and supply decoupling. Operating on a 3 V supply, its 13.7 mA consumption (for TA = 25°C) is only 41 mW. A power-down feature is provided; the input is taken high to initiate a low current (20 µA) sleep mode, with a threshold at half the supply voltageThe AD8313 is fabricated on Analog Devices, Inc., advanced 25 GHz silicon bipolar IC process and is available in an 8-lead MSOP package. The operating temperature range is −40°C to +85°C.

The AD8314 is a complete low cost subsystem for the measurement and control of RF signals in the frequency range of 100 MHz to 2.7 GHz, with a typical dynamic range of 45 dB, intended for use in a wide variety of cellular handsets and other wireless devices. It provides a wider dynamic range and better accuracy than possible using discrete diode detectors. In particular, its temperature stability is excellent over the full operating range of -40°C to +85°C.The AD8314 is available in 8-lead MSOP and 8-lead LFCSP packages and consumes 4.5 mA from a 2.7 V to 5.5 V supply. When powered down, the typical sleep current is 20 µA.An evaluation board is available for this product and may be ordered using the following product number: AD8314-EVAL. Schematic and layout for this evaluation board is contained in the product datasheet.

The AD8315 is a complete low cost subsystem for the precisecontrol of RF power amplifiers operating in the frequency range0.1 GHz to 2.5 GHz and over a typical dynamic range of 50 dB.It is intended for use in cellular handsets and other batteryoperatedwireless devices. The log amp technique provides a muchwider measurement range and better accuracy than controllersusing diode detectors. In particular, the temperature stability isexcellent over a specified range of −30°C to +85°C.Its high sensitivity allows control at low signal levels, thusreducing the amount of power that must be coupled tothe detector.For convenience, the signal is internally ac-coupled. Thishigh-pass coupling, with a corner at approximately 0.016 GHz,determines the lowest operating frequency. Therefore, thesource can be dc grounded.The AD8315 provides a voltage output, VAPC, that has thevoltage range and current drive to directly connect to mosthandset power amplifiers’ gain control pin. VAPC can swingfrom 250 mV above ground to within 200 mV below the supplyvoltage. Load currents of up to 6 mA can be supported.The setpoint control input is applied to the VSET pin and hasan operating range of 0.25 V to 1.4 V. The associated circuitdetermines the slope and intercept of the linear-in-dBmeasurement system; these are nominally 23 mV/dB and−60 dBm for a 50 Ω termination (−73 dBV) at 0.9 GHz.Further simplifying the application of the AD8315, the inputresistance of the setpoint interface is over 100 MΩ, and the biascurrent is typically 0.5 μA.The AD8315 is available in MSOP and LFCSP packages andconsumes 8.5 mA from a 2.7 V to 5.5 V supply. When powereddown, the sleep current is 4 μA. Applications Single, dual, and triple band mobile handset (GSM, DCS, EDGE) Transmitter power control

The AD8553 is a precision instrumentation amplifierfeaturing low noise, rail-to-rail output and a power-savingshutdown mode. The AD8553 also features low offset anddrift coupled with high common mode rejection. Inshutdown mode, the total supply current is reduced to lessthan 4 µA. Operation is fully specified from +1.8V to+5.5V.With low offset voltage of 20µV, offset voltage drift of0.1µV/°C and voltage noise of only 0.7µV p-p (0.01Hz to10 Hz), the AD8553 is ideal for applications where errorsources cannot be tolerated. Precision instrumentation,position and pressure sensors, medical instrumentation,and strain gauge amplifiers benefit from the low noise, lowinput bias current, and high common mode rejection. Thesmall footprint and low cost are ideal for high volumeapplications.The small package and low power consumption allowmaximum channel density or minimum board size forspace-critical equipment and portable systems.The AD8553 is specified over the industrial temperaturerange from -40°C to +85°C. The AD8553 is available inthe lead-free 10-lead MSOP.

The AD8661 / AD8662 / AD8664 are rail-to-rail output, single-supplyamplifiers that use the Analog Devices, Inc., patentedDigiTrim® trimming technique to achieve low offset voltage.The AD8661 / AD8662 / AD8664 series features extendedoperating ranges, with supply voltages up to 16 V. It alsofeatures low input bias current, wide signal bandwidth,and low input voltage and current noise.The combination of low offset, very low input bias current,and a wide supply range makes these amplifiers useful in a widevariety of applications usually associated with higher priced JFETamplifiers. Systems using high impedance sensors, such asphotodiodes, benefit from the combination of low input biascurrent, low noise, low offset, and wide bandwidth. The wideoperating voltage range meets the demands of high performanceanalog-to-digital converters (ADCs) and digital-to-analogconverters (DACs). Audio applications and medical monitoringequipment can take advantage of the high input impedance, lowvoltage, low current noise, and wide bandwidth.The single AD8661 is available in a narrow 8-lead SOIC packageand a very thin, dual lead, 8-lead LFCSP. The AD8661 SOICpackage is specified over the extended industrial temperaturerange of −40°C to +125°C. The AD8661 LFCSP is specified overthe industrial temperature range of −40°C to +85°C. The AD8662is available in a narrow 8-lead SOIC package and an 8-lead MSOP,both specified over the extended industrial temperature range of−40°C to +125°C. The AD8664 is available in a narrow 14-leadSOIC package and a 14-lead TSSOP, both with an extendedindustrial temperature range of −40°C to +125°C.Applications Sensors Medical equipment Consumer audio Photodiode amplification ADC drivers

The ADR430/ADR431/ADR433/ADR434/ADR435 series is a family of XFET® voltage references featuring low noise, high accuracy, and low temperature drift performance. Using Analog Devices, Inc., temperature drift curvature correction and extra implanted junction FET (XFET) technology, voltage change vs. temperature nonlinearity in the ADR430/ADR431/ADR433/ADR434/ ADR435 is minimized.The XFET references operate at lower current (800 μA) and lower supply voltage headroom (2 V) than buried Zener references. Buried Zener references require more than 5 V of headroom for operation. The ADR430/ADR431/ADR433/ADR434/ADR435 XFET references are low noise solutions for 5 V systems.The ADR430/ADR431/ADR433/ADR434/ADR435 family has the capability to source up to 30 mA of output current and sink up to −20 mA. It also comes with a trim terminal to adjust the output voltage over a ±0.5% range without compromising performance.The ADR430/ADR431/ADR433/ADR434/ADR435 are available in 8-lead MSOP and 8-lead narrow SOIC packages. All versions are specified over the extended industrial temperature range of −40°C to +125°C.Applications Precision data acquisition systems High resolution data converters Medical instruments Industrial process control systems Optical control circuits Precision instruments

The ADT75 is a complete temperature monitoring system in 8-lead MSOP and SOIC packages. It contains a band gap temperature sensor and 12-bit Aanalog-to-digital converter (ADC) to monitor and digitize the temperature to a resolution of 0.0625°C. The ADT75 is pin and register compatible with the LM75 and AD7416.The ADT75 is specified for operation at supply voltages from 2.7 V to 5.5 V. Operating at 3.3 V, the average supply current is typically 200 μA.The ADT75 offers a shutdown mode that powers down the device and this mode gives a shutdown current of typically 3 μA. The ADT75 is rated for operation over the –55°C to +125°C temperature range.The A0, A1, and A2 pins are available for address selection. The OS/ALERT pin is an open-drain output that becomes active when temperature exceeds a programmable limit. The OS/ALERT pin can operate in either comparator or interrupt mode.Product Highlights On-chip temperature sensor allows an accurate measurement of the ambient temperature. The measurable temperature range is −55°C to +125°C. Supply voltage is 2.7 V to 5.5 V. Space-saving, 8-lead MSOP and 8-lead SOIC. Temperature accuracy is ±1°C maximum. Temperature resolution is 0.0625°C. Shutdown mode reduces the current consumption to 3 μA typical. Connect up to eight ADT75s to a single SMBus/I2C bus.Applications Isolated Sensors Environmental Control Systems Computer Thermal Monitoring Thermal Protection Industrial Process Control Power-system Monitors Hand Held Applications

The AD7277 is a 10-bit, high speed, low power, successive-approximation ADC. The parts operate from a single 2.35 V to 3.6 V power supply and feature throughput rates of up to 3 MSPS. The parts contain a low noise, wide bandwidth track-and-hold amplifier that can handle input frequencies in excess of 55 MHz.The conversion process and data acquisition are controlled using CS and the serial clock, allowing the devices to interface with microprocessors or DSPs. The input signal is sampled on the falling edge of CS, and the conversion is also initiated at this point. There are no pipeline delays associated with the part. The AD7277 uses advanced design techniques to achieve very low power dissipation at high throughput rates. The reference for the part is taken internally from VDD. This allows the widest dynamic input range to the ADC; therefore, the analog input range for the part is 0 to VDD. The conversion rate is determined by the SCLK.PRODUCT HIGHLIGHTS 3 MSPS ADCs in a 6-lead TSOT package. AD7476 / AD7477 / AD7478 and AD7476A / AD7477A / AD7478A pin-compatible. High throughput with low power consumption. Flexible power/serial clock speed management. This allows maximum power efficiency at low throughput rates. Reference derived from the power supply. No pipeline delay. The parts feature a standard successive approximation ADC with accurate control of the sampling instant via a CS input and once-off conversion control.

The AD5624 / AD5664, members of the nanoDAC® family, are low power, quad, 12-, 16-bit buffered voltage-out DACs that operate from a single 2.7 V to 5.5 V supply and are guaranteed monotonic by design.The AD5624 / AD5664 require an external reference voltage to set the output range of the DAC. The part incorporates a power-on reset circuit that ensures the DAC output powers up to 0 V and remains there until a valid write takes place. The parts contain a power-down feature that reduces the current consumption of the device to 480 nA at 5 V and provides software-selectable output loads while in power-down mode.The low power consumption of these parts in normal operation makes them ideally suited to portable battery-operated equipment. The power consumption is 2.25 mW at 5 V, going down to 2.4 μW in power-down mode.The AD5624 / AD5664 on-chip precision output amplifier allows rail-to-rail output swing to be achieved. The AD5624/AD5664 use a versatile 3-wire serial interface that operates at clock rates up to 50 MHz, and are compatible with standard SPI®, QSPI™, MICROWIRE™, and DSP interface standards.PRODUCT HIGHLIGHTS Relative accuracy: ±12 LSBs maximum. Available in 10-lead MSOP and 10-lead, 3 mm × 3 mm, LFCSP_WD. Low power, typically consumes 1.32 mW at 3 V and 2.25 mW at 5 V. Maximum settling time of 4.5 μs (AD5624) and 7 μs (AD5664).APPLICATIONS Process control Data acquisition systems Portable battery-powered instruments Digital gain and offset adjustment Programmable voltage and current sources Programmable attenuators

The AD8012 is a dual, low power, current feedback amplifiercapable of providing 350 MHz bandwidth while using only1.7 mA per amplifier. It is intended for use in high frequency,wide dynamic range systems where low distortion and highspeed are essential and low power is critical.With only 1.7 mA of supply current, the AD8012 also offersexceptional ac specifications such as 20 ns settling time and2,250 V/μs slew rate. The video specifications are 0.02% differentialgain and 0.06 degree differential phase, excellent for sucha low power amplifier. In addition, the AD8012 has a low offsetof 1.5 mV.The AD8012 is well suited for any application that requires highperformance with minimal power.The product is available in standard 8-lead SOIC or MSOPpackages and operates over the industrial temperature range–40°C to +85°C.Applications XDSL, HDSL Line Drivers ADC Buffers Professional Cameras CCD Imaging Systems Ultrasound Equipment Digital Cameras