High Speed, Triple Differential Receiver with Comparators Features: High speed: 500 MHz, 2000 V/μs @ G = 1, VOUT = 2 V p-p 0.1 dB flatness out to 75 MHz High CMRR: 69 dB @ 10 MHz High differential input impedance: 1 MΩ Wide input common-mode range: ±3.5 V (±5 V supplies) On-chip, gain setting resistors can be configured for gain of 1 or 2 Fast settling: 15 ns to 0.1% @ 2 V p-p Low input referred noise: 13 nV/√Hz Disable feature Small packaging: 32-lead, 5 mm × 5 mm LFCSP AEC-Q10 qualified (AD8145W)

36 V, 19 MHz, Low Noise, Low Bias Current, JFET Op Amp Features: Low offset voltage: 200 μV maximum Offset drift: 1 μV/°C typical Very low input bias current: 5 pA maximum Extended temperature range: −40ºC to +125ºC ±5 V to ±15 V dual supply ADA4627-1 GBW: 19 MHz ADA4637-1 GBW: 79 MHz See data sheet for additional information

Zero-Drift, Single-Supply, RRIO Op Amp Features:Lowest auto-zero amplifier noise Low offset voltage: 1 μV Input offset drift: 0.002 μV/°C Rail-to-rail input and output swing 5 V single-supply operation High gain, CMRR, and PSRR: 130 dB Very low input bias current: 100 pA maximum Low supply current: 1.0 mA Overload recovery time: 50 μs No external components required Qualified for automotive applications

2, 31.76 W, Digital Input, Filterless Stereo Class D Audio Amplifier Features: Digital input stereo, high efficiency Class-D amplifier Operates from a single 4.5 V to 16.5 V supply State-of-the-art, proprietary, filterless - modulation 106.5 dB SNR at PO = 8.1 W, RL = 8 , AV = 19 dB, PVDD = 12 V, A weighted 0.004% THD + N at 5 W into 8 38.5 V rms output voltage noise, f = 20 Hz to 20 kHz, A weighted, PVDD = 16 V, 8 Pop and clickless on and off sequence 2 14.67 W output at 12 V supply to 4 loads at <1% THD + N 2 14.4 W output at 16 V supply to 8 loads at <1% THD + N Mono mode for increased maximum output power 1 49.69 W output at 16 V supply to 2 loads at <1% THD + N Support for low impedance loads As low as 3 Ω/5 μH in stereo mode As low as 2 Ω/5 μH in mono mode High power efficiency 93.8% efficiency into an 8 Ω load 90.6% efficiency into a 4 Ω load 12.34 mA quiescent current with single 12 V PVDD supply Single-supply operation with internal LDOs or option to use an external 5 V and 1.8 V supply for lowest power consumption I2C control and hardware modes with up to 16 pin-selectable slots/addresses Supported sample rates from 8 kHz to 192 kHz with 24-bit resolution Multiple PCM audio serial data formats TDM slave with support for up to 16 devices on a single bus I2S or left justified slave Adjustable full-scale output tailored for many PVDD sources 2- and 3-cell Li-Ion batteries Digital volume control with selectable smooth ramp Automatic power-down function Supply monitoring automatic gain control (AGC) function reduces system brownout Standalone operational mode without I2C Temperature sensor with 1°C step readout via I2C Short-circuit, undervoltage, and thermal protection Thermal early warning Power-on reset PVDD sensing ADC 40-lead, 6 mm × 6 mm LFCSP with thermal pad

OP-AMP, 2.7MHZ, MSOP-8, -40 TO 125DEG C;

Op-Amp, 2.5Mhz, -40 To 125Deg C, Msop-8 |Analog Devices MAX74811ARMZ-R7

50V ZDA, LOW NOISE;

Low Cost, Single, 300 MHz Voltage Feedback Amplifier Features: Low cost Easy to use voltage feedback architecture High speed 300 MHz, -3 dB bandwidth (G = +1) 1400 V/µs slew rate 20 ns settling to 0.1% Low distortion: -72 dBc @ 10 MHz Low noise: 6 nV/√Hz Low dc rrrors: 5mV max VOS, 1.2 µA max IB Small packaging High output drive current: over 60 mA Excellent video specifications (RL = 150 Ω, G = +2) Gain flatness 0.1 dB to 40 MHz 0.01% differential gain error 0.02° differential phase error Drives 4 video loads (37.5 V) with 0.02% differential gain and 0.1° differential phase Low power, ±5 V supplies 5 mA typ/amplifier power supply current

Triple Differential Driver with Output Pull-Down Features: Triple high speed fully differential driver 225 MHz −3 dB large signal bandwidth Easily drives 1.4 V p-p video signal into source-terminated 100 UTP cable 1600 V/µs slew rate Fixed internal gain of 2 Internal common-mode feedback network Output balance error −60 dB @ 50 MHz Differential input and output Differential-to-differential or single-ended-to-differential operation Adjustable output common-mode voltage Output pull-down feature for line isolation Low distortion: 64 dB SFDR @ 10 MHz on 5 V supply, RL, dm = 200 Low offset: 4 mV typical output referred on 5 V supply Low power: 26 mA @ 5 V for three drivers Wide supply voltage range: +5 V to ±5 V Available in space-saving packaging: 4 mm × 4 mm LFCSP

IC Differential Amplifier SINGLE TSSOP 8PIN PLASTIC