High Performance, Low Power, Rail-to-Rail Precision Instrumentation Amplifier Features: Low power: 330 μA maximum quiescent current Rail-to-rail output Low noise and distortion 8 nV/√Hz maximum input voltage noise at 1 kHz 0.15 μV p-p RTI noise (G = 100) 0.5 ppm nonlinearity with 2 kΩ load (G = 1) Excellent ac specifications 80 dB minimum CMRR at 10 kHz (G = 1) 2.2 MHz bandwidth (G = 1) High precision dc performance (AD8422BRZ) 150 dB minimum CMRR (G = 1000) 0.04% maximum gain error (G = 1000) 0.3 μV/°C maximum input offset drift 0.5 nA maximum input bias current Wide supply range 4.6 V to 36 V single supply ±2.3 V to ±18 V dual supply Input overvoltage protection: 40 V from opposite supply Gain range: 1 to 1000 Available in 8-lead LFCSP, 8-lead MSOP, and 8-lead SOIC_N

60 MHz, 2000 V/s, Monolithic Op Amp with Quad Low Noise Features: Wide bandwidth 60 MHz at gain of −1  33 MHz at gain of −10  Slew rate: 2000 V/μs  20 MHz full power bandwidth, 20 V p-p, RL = 500 Ω  Fast settling: 100 ns to 0.1% (10 V step) Differential gain error: 0.03% at 4.4 MHz  Differential phase error: 0.16° at 4.4 MHz  Low offset voltage: 150 μV maximum (B Grade) Low quiescent current: 6.5 mA  Available in tape and reel in accordance with EIA-481-A standard

Digitally Programmable Sensor Signal Amplifier with EMI Filters Features: EMI filters at input pins Specified from −40°C to +140°C Low offset voltage: 10 μV maximum Low input offset voltage drift: 65 nV/°C maximum High CMRR: 94 dB minimum Digitally programmable gain and output offset voltage Programmable output clamp voltage Open and short wire fault detection Low-pass filtering Single-wire serial interface Stable with any capacitive load SOIC_N and LFCSP_VQ packages 4.5 V to 5.5 V operation

Ultrafast 7 ns Single Supply Comparator Features: 7 ns propagation delay at 5 V Single supply operation: 3 V to 10 V Low power Latch function TSSOP packages

3000 V/S, 35mW Current Feedback Quad Amplifier Features: High speed 250 MHz -3 dB bandwidth (G = +1) 3000 V/µs slew rate 21 ns settling time to 0.1% 1.8 ns rise time for 2 V step Low power 3.5 mA/amp power supply Current (35 mW/amp) Single supply operation Fully specified for +5 V supply High output current of 50 mA Good video specifications (RL = 150 Ω, G = +2) Gain flatness 0.1 dB to 30 MHz 0.04% differential gain error 0.10° differential phase error Low distortion –78 dBc THD at 5 MHz –61 dBc THD at 20 MHz Available in a 14-lead SOIC

160 MHz Rail-to-Rail Amplifier with Disable Features: Fully specified for +3 V, +5 V and ±5 V Supplies Output Swings Rail to Rail Input Voltage Range Extends 200 mV Below Ground No Phase Reversal with Inputs 1 V Beyond Supplies Disable/Power-Down Capability Low Power of 5.2 mA (26 mW on 5 V) High Speed and Fast Settling on 5 V: 160 MHz -3 dB Bandwidth (G = +2) 160 V/µs Slew Rate 30 ns Settling Time to 0.1% Good Video Specifications (RL = 150 Ω, G = +2) Gain Flatness of 0.1 dB to 30 MHz 0.03% Differential Gain Error 0.03° Differential Phase Error Low Distortion -69 dBc Worst Harmonic @ 10 MHz Outstanding Load Drive Capability Drives 50 mA 0.5 V from Supply Rails Cap Load Drive of 45 pF

Triple Differential Receiver with Adjustable Line Equalization Features: Compensates cables to 300 meters for wideband video Fast rise and fall times 4.9 ns with 2 V step at 150 meters of UTP cable 8.0 ns with 2 V step at 300 meters of UTP cable 55 dB peak gain at 100 MHz Two frequency response gain adjustment pins High frequency peaking adjustment (VPEAK) Broadband flat gain adjustment (VGAIN) Pole location adjustment pin (VPOLE) Compensates for variations between cables Can be optimized for either UTP or coaxial cable DC output offset adjust (VOFFSET) Low output offset voltage: 24 mV Compensates both RGB and YPbPr Two on-chip comparators with hysteresis Can be used for common-mode sync extraction Available in 40-lead, 6 mm × 6 mm LFCSP

Low Cost 270 MHz Differential Receiver Amplifier Features: High Speed AD8130: 270 MHz, 1090 V/µs @ G = +1 AD8129: 200 MHz, 1060 V/µs @ G = +10 High CMRR 94 dB min, dc to 100 kHz 80 dB min @ 2 MHz 70 dB @ 10 MHz Low noise AD8130: 12.5 nV/√Hz AD8129: 4.5 nV/√Hz High input impedance: 1 MΩ differential Input common-mode range ±10.5 V Low distortion, 1 V p-p @ 5 MHz: AD8130, -79 dBc worst harmonic @ 5 MHz AD8129, -74 dBc worst harmonic @ 5 MHz User-adjustable gain No external components for G = +1 Power supply range +4.5 V to ±12.6 V Power-down

Triple Differential Driver for Wideband Video Features:Triple high speed fully differential driver700 MHz, 3 dB, 2 V p-p bandwidth (AD8146/AD8148)600 MHz, 3 dB, 2 V p-p bandwidth (AD8147)200 MHz, 0.1 dB, 2 V p-p bandwidth3000 V/s slew rate Fixed gain (AD8146/AD8147: G = 2, AD8148: G = 4) Differential or single-ended input to differential output Can be used as differential-to-differential receiver Drives one or two 100 UTP cables Adjustable output common-mode voltage (AD8146) Internal common-mode feedback network Output balance error 50 dB @ 50 MHz On-chip, sync-on common-mode encoding (AD8147/AD8148) Output pull-down feature for line isolation Low power: 57 mA @ 5 V for 3 drivers (AD8146) Wide supply voltage range: +5 V to 5 V Available in a small 4 mm 4 mm LFCSP

High Voltage, Current Shunt Monitor Features: ±4000 V HBM ESD High common-mode voltage range −2 V to +65 V operating −3 V to +68 V survival Buffered output voltage Wide operating temperature range 8-Lead SOIC_N: −40°C to +125°C Excellent ac and dc performance 6 μV/°C typical offset drift −8 ppm/°C typical gain drift 120 dB typical CMRR at dc Qualified for Automotive Applications