The AD7233 is a complete 12-bit, voltage-output, digital-to-analog converter with output amplifier and Zener voltage reference all in an 8-pin package. No external trims are required to achieve full specified performance. The data format is 2s complement, and the output range is -5V to +5V.The AD7233 features a fast, versatile serial interface which allows easy connection to both microcomputers and 16-bit digital signal processors with serial ports. When the SYNC input is taken low, data on the SDIN pin is clocked into the input shift register on each falling edge of SCLK. On completion of the 16-bit data transfer, bringing LDAC low updates the DAC latch with the lower 12 bits of data and updates the output. Alternatively, LDAC can be tied permanently low, and in this case the DAC register is automatically updated with the contents of the shift register when all sixteen data bits have been clocked in. The serial data may be applied at rates up to 5 MHz allowing a DAC update rate of 300 kHz.For applications which require greater flexibility and unipolar output ranges with single supply operation, please refer to the AD7243 data sheet.The AD7233 is fabricated on Linear Compatible CMOS (LC2MOS), an advanced, mixed-technology process. It is packaged in an 8-pin DIP package.

Tiny 16-Bit SPI nanoDAC+, with 2 (16-Bit) LSB INL and 2 ppm/C Reference Features: Ultrasmall package: 2 mm × 2 mm, 8-lead LFCSP High relative accuracy (INL): ±2 LSB maximum at 16 bits AD5683R/AD5682R/AD5681R Low drift, 2.5 V reference: 2 ppm/°C typical Selectable span output: 2.5 V or 5 V Total unadjusted error (TUE): 0.06% of FSR maximum Offset error: ±1.5 mV maximum Gain error: ±0.05% of FSR maximum Low glitch: 0.1 nV-sec High drive capability: 20 mA Low power: 1.2 mW at 3.3 V Independent logic supply: 1.62 V logic compatible Wide operating temperature range: −40°C to +105°C Robust 4 kV HBM ESD protection

8-Channel, 1.5 MSPS, 12-Bit Parallel ADCs with a Sequencer Features: Throughput rate: 1.5 MSPS Specified for VDD of 2.7 V to 5.25 V 8 analog input channels with a sequencer Software-configurable analog inputs 8-channel single-ended inputs 4-channel fully differential inputs 4-channel pseudo differential inputs 7-channel pseudo differential inputs Accurate on-chip 2.5 V reference ±0.2% maximum at 25°C, 25 ppm/°C maximumPower consumption 6 mW maximum at 1.5 MSPS with 3 V supplies 13.5 mW maximum at 1.5 MSPS with 5 V supplies 69 dB SINAD at 50 kHz input frequency No pipeline delays High speed parallel interface—word/byte modes Full shutdown mode: 2 μA maximum 32-lead LFCSP and TQFP packages

12-bit Digital-to-Analog Converters, with Zener Reference Features: Single Chip Construction Very High Speed Settling to 1/2 LSB AD565A: 250 ns max Full-Scale Switching Time: 30 ns Guaranteed for Operation with ±12 V (AD565A) Supplies Low Cost Linearity Guaranteed Over temperature 1/2 LSB max (K, T Grades) Monotonicity Guaranteed Over temperature Low Power = 225mW max Use with On-Board High Stability Reference

4T4R Direct RF Receiver and Transmitter Features: Flexible, reconfigurable radio common platform design Transmitter/receiver channel bandwidth up to 1.2 GHz (4T4R) RF DAC/RF ADC RF frequency range up to 7.5 GHz On-chip PLL with multichip synchronization External RF clock input option Versatile digital features Selectable interpolation and decimation filters Configurable DDCs and DUCs 8 fine complex DUCs (FDUC) and 4 coarse complex DUCs (CDUC) 8 fine complex DDCs (FDDC) and 4 coarse complex DDCs (CDDC) FDUCs and FDDCs are fully bypassable 2 independent 48-bit NCOs per DUC or DDC Programmable 192-tap PFIR filter for receive equalization Supports 4 different profile settings loaded via GPIO Receive AGC support Fast detect with low latency for fast AGC control Signal monitor for slow AGC control Dedicated AGC support pins Transmit DPD support Programmable delay and gain per transmit data path Coarse DDC delay adjust for DPD observation path Supports real or complex digital data (8-, 12-, or 16-bit) Auxiliary features ADC clock driver with selectable divide ratios Power amplifier downstream protection circuitry On-chip temperature monitoring unit Programmable GPIO pins support toggling between modes TDD power savings option and sharing ADCs SERDES JESD204B or JESD204C interface, 16 lanes up to 24.75 Gbps 8 lanes JESD204B/C transmitter (JTx) and 8 lanes JESD204B/C receiver (JRx) Supports Subclass 1 Supports multidevice synchronization 15 mm × 15 mm, 324-ball BGA with 0.8 mm pitch

The ADPD4200 operates as a complete multimodal sensor front end, stimulating up to four light emitting diodes (LEDs) and measuring the return signal on up to four separate current inputs. Twelve time slots are available, enabling 12 separate measurements per sampling period.The data output and functional configuration utilize a serial port interface (SPI) on the ADPD4200. The control circuitry includes flexible LED signaling and synchronous detection. The device uses a 1.8 V analog core and 1.8 V or 3.3 V compatible digital input/output (I/O).The analog front end (AFE) rejects signal offsets and corruption from asynchronous modulated interference, typically from ambient light, eliminating the need for optical filters or externally controlled dc cancellation circuitry. Multiple operating modes are provided, enabling the ADPD4200 to be a sensor hub for synchronous measurements of photodiodes, biopotential electrodes, resistance, capacitance, and temperature sensors.The ADPD4200 is available in a 2.619 mm ? 1.804 mm, 0.40 mm pitch, 24-ball WLCSP.Analog Devices is in the process of updating documentation to provide terminology and language that is culturally appropriate. This is a process with a wide scope and will be phased in as quickly as possible. Thank you for your patience.APPLICATIONS Wearable health and fitness monitors: heart rate monitors (HRMs), heart rate variability (HRV), stress, blood pressure estimation, SpO2, hydration, and body composition Industrial monitoring: CO, CO2, smoke, and aerosol detection Home patient monitoring

The ADuM7703 is a high performance, second-order, ?-? analog-to-digital converter (ADC) with an integrated low dropout (LDO) regulator that converts an analog input signal into a high speed, single-bit data stream with on-chip digital isolation based on Analog Devices, Inc., iCoupler? technology. The device operates from a 4.5 V to 20 V power supply range (VDD1) and accepts a pseudo differential input signal of ?250 mV (?320 mV full-scale). The pseudo differential input is ideally suited to shunt voltage monitoring in high voltage applications where galvanic isolation is required.The analog input is continuously sampled by a high performance analog modulator and converted to a ones density digital output stream with a data rate of up to 21 MHz. The original information can be reconstructed with an appropriate sinc3 digital filter to achieve an 86 dB signal-to-noise ratio (SNR) at 78.1 kSPS with a 256 decimation rate and a 20 MHz master clock. The serial input and output operates from a 5 V or a 3.3 V supply (VDD2).The serial interface is digitally isolated. High speed complementary metal-oxide semiconductor (CMOS) technology, combined with monolithic transformer technology, results in the on-chip isolation providing outstanding performance characteristics, superior to alternatives such as optocoupler devices. The ADuM7703 device is available in a 16-lead, wide-body SOIC with an operating temperature range of ?40?C to +125?C and an 8-lead, wide-body SOIC with an operating temperature range of ?40?C to +105?C.Applications Shunt current monitoring AC motor controls Power and solar inverters Wind turbine inverters Analog-to-digital and optoisolator replacement

Complete Quad, 16-Bit, High Accuracy, Serial Input, Bipolar Voltage Output DAC Features: Complete quad, 16-bit digital-to-analog converters (DAC) Programmable output range: ±10 V, ±10.2564 V, or ±10.5263 V ±1 LSB max INL error, ±1 LSB maximum DNL error Low noise: 60 nV/√Hz Settling time: 10 µs maximum Integrated reference buffers Internal reference: 10 ppm/°C maximum On-chip die temperature sensor Output control during power-up/brownout Programmable short-circuit protection Simultaneous updating via LDAC Asynchronous CLR to zero code Digital offset and gain adjust See Data Sheet for Additional Information

The AD7766/AD7766-1/AD7766-2 are high performance,24-bit, oversampled SAR analog-to-digital converters (ADCs).The AD7766/AD7766-1/AD7766-2 combine the benefits of alarge dynamic range and input bandwidth, consuming 15 mW,10.5 mW, and 8.5 mW power, respectively, and are contained ina 16-lead TSSOP package.Ideal for ultralow power data acquisition (such as PCI- and USBbasedsystems), the AD7766/AD7766-1/AD7766-2 provide 24-bitresolution. The combination of exceptional SNR, wide dynamicrange, and outstanding dc accuracy make the AD7766/AD7766-1/AD7766-2 ideally suited for measuring small signal changes over awide dynamic range. This is particularly suitable for applicationswhere small changes on the input are measured on larger ac ordc signals. In such an application, the AD7766/AD7766-1/AD7766-2 accurately gather both ac and dc information.The AD7766/AD7766-1/AD7766-2 include an on-board digitalfilter (complete with linear phase response) that acts to eliminateout-of-band noise by filtering the oversampled input voltage.The oversampled architecture also reduces front-end antialiasrequirements. Other features of the AD7766/AD7766-1/AD7766-2include a SYNC/PD (synchronization/power-down) pin, allowingthe synchronization of multiple AD7766/AD7766-1/AD7766-2devices. The addition of an SDI pin provides the option of daisychaining multiple AD7766/AD7766-1/AD7766-2 devices.The AD7766/AD7766-1/AD7766-2 operate from a 2.5 V supplyusing a 5 V reference. The devices operate from ?40?C to +105?C. Applications Low power PCI/USB data acquisition systems Low power wireless acquisition systems Vibration analysis Instrumentation High precision medical acquisition

The?AD7792/AD7793 are low power, low noise, complete analog front ends for high precision measurement applications. The AD7792/AD7793 contain a low noise 16-/24-bit ?-? ADC with three differential analog inputs. The on-chip, low noise instrumentation amplifier means that signals of small amplitude can be interfaced directly to the ADC. With a gain setting of 64, the rms noise is 40 nV when the update rate equals 4.17 Hz.The devices contain a precision low noise, low drift internal band gap reference and can accept an external differential reference. Other on-chip features include programmable excitation current sources, burnout currents, and a bias voltage generator. The bias voltage generator sets the common-mode voltage of a channel to AVDD/2The devices can be operated with either the internal clock or an external clock. The output data rate from the parts is software-programmable and can be varied from 4.17 Hz to 470 Hz.The parts operate with a power supply from 2.7 V to 5.25 V. They consume a current of 400 ?A typical and are housed in a 16-lead TSSOP package.Applications Thermocouple measurements RTD measurements Thermistor measurements Gas analysis Industrial process control Instrumentation Portable instrumentation Blood analysis Smart transmitters Liquid/gas chromatography 6-digit DVM