Power Management IC Development Tools LTC4260CGN - 200W Positive 48V Hot Swap

Voltage References LT1019 - Precision Reference

The HMC976LP3E is a BiCMOS ultra low noise linear voltage regulator. The high Power Supply Rejection Ratio (PSRR) in the 0.1 MHz to 10 MHz range provides excellent rejection of any preceding switching regulator or other power supply noise. The voltage output is ideal for frequency generation subsystems including Hittite’s broad line of PLLs with integrated VCOs. The output voltage can be adjusted lower than the default value by using one external resistor.The output can be set to 5V by grounding the HV pin. The regulator can be powered down by the TTL-compatible Enable input. The HMC976LP3E is housed in a 3x3mm QFN SMT package.Applications Test Instrumentation Military Radios, Radar and ECM Basestation Infrastructure Ultra Low Noise Frequency Generation Fractional-N Synthesizer Supply Mixed-Signal Circuit Supply

Power Management IC Development Tools LTC4088EDE-1 Demo Board- High Efficiency

Power Management IC Development Tools LTC4215 Demoboard - Hot Swap Controller

Non-Isolated PoL Module DC DC Converter 2 Output 0.6 ~ 2.5V 0.6 ~ 2.5V - - 13A, 13A 4.5V - 16V Input

Ultralow Noise 1A Switching Regulator Features: Greatly Reduced Conducted and Radiated EMI (<100µVP-P in Typical Application) Low Switching Harmonic Content Independent Control of Switch Voltage and Current Slew Rates Two 1A Current Limited Power Switches Regulates Positive and Negative Voltages 20kHz to 250kHz Oscillator Frequency Easily Synchronized to External Clock Wide Input Voltage Range: 2.7V to 23V Low Shutdown Current: 12µA Typical Easier Layout than with Conventional Switchers Outputs Can Be Forced to 50% Duty Cycle for Unregulated Applications

Precision Wide-range (3 nA - 3 mA) High-Side Current Mirror Features: Accurately mirrors input current (1:1 ratio) over 6 decades - enables monitoring at low signal levels  Linearity 1% from 3 nA to 3 mA Stable mirror input voltage Voltage held 1 V below supply using internal reference or may be set externally providing greater flexibility in design Adjustable input current limit provides protection to the connected photodiode 2.7 V to 8 V single-supply operation Miniature 8-lead chip scale package (LFCSP 2 mm × 3 mm) saves valuable board space

Hot Swap Controller and Digital Power and Energy Monitor with PMBus Interface Features: ±0.3% accurate, 12-bit ADC for IOUT, VIN, VOUT, and temperature 320 ns response time to short circuit Shutdown on detection of FET health fault Constant power foldback for tighter FET SOA protection Remote temperature sensing with programmable warning and shutdown thresholds Resistor-programmable 5 mV to 25 mV VSENSE current limit Programmable start-up current limit 1% accurate UV, OV, and PWRGD thresholds Split hot swap and power monitor inputs to allow additional external ADC filtering Reports power and energy consumption over time Peak detect registers for current, voltage, and power PROCHOT power throttling capability PMBus fast mode compliant interface 5 mm × 5 mm, 32-lead LFCSP

1 A/0.6 A, DC-to-DC Switching Regulator with Independent Positive and Negative Outputs Features: Wide input supply voltage range: 2.85 V to 15 V Generates well regulated, independently resistor programmable VPOS and VNEG outputs Boost regulator to generate VPOS output Adjustable positive output to 39 V Integrated 1.0 A main switch Optional single-ended primary-inductor converter (SEPIC) configuration for automatic step-up/step-down Inverting regulator to generate VNEG output Adjustable negative output to VIN − 39 V Integrated 0.6 A main switch True shutdown for both positive and negative outputs 1.2 MHz/2.4 MHz switching frequency with optional external frequency synchronization from 1.0 MHz to 2.6 MHz Resistor programmable soft start timer Slew rate control for lower system noise Individual precision enable and flexible start-up sequence control for symmetric start, VPOS first, or VNEG first Out-of-phase operation UVLO, OCP, OVP, and TSD protection 4 mm × 4 mm, 20-lead LFCSP and 20-lead TSSOP −40°C to +125°C junction temperature range Supported by the ADIsimPower tool set