Dual Output PolyPhase Step-Down DC/DC Voltage Mode Controller with Digital Power System Management Features: PMBus/I2C Compliant Serial Interface Monitor Voltage, Current, Temperature and Faults Digitally Programmable Voltage, Current Limit, Soft-Start/Stop, Sequencing, Margining, AVP and UV/OV Thresholds 3V ≤ VINSNS ≤ 38V, 0.5V ≤ VOUT ≤ 5.25V ±0.5% Output Voltage Accuracy Programmable PWM Frequency or External Clock Synchronization from 250kHz to 1.25MHz Accurate PolyPhase® Current Sharing Internal EEPROM with Fault Logging and ECC IC Supply Range: 3V to 13.2V Resistor or Inductor DCR Current Sensing Optional Resistor Programming for Key Parameters 40-Pin (6mm × 6mm) QFN Package AEC-Q100 Qualified for Automotive Applications

Boost/SEPIC/Inverting DC/DC Converter with 1A, 65V Switch, Soft-Start and Synchronization Features: 1A, 65V Power Switch Adjustable Switching Frequency Single Feedback Resistor Sets VOUT Synchronizable to External Clock High Gain SHDN Pin Accepts Slowly Varying Input Signals Wide Input Voltage Range: 2.55V to 40V Low VCESAT Switch: 400mV at 0.75A (Typical) Integrated Soft-Start Function Easily Configurable as a Boost, SEPIC, or Inverting Converter User Configurable Undervoltage Lockout (UVLO) Pin Compatible with LT3580 Tiny Thermally Enhanced 8-Lead 3mm × 3mm DFN and 8-Lead MSOP Packages AEC-Q100 Qualified for Automotive Applications

60V Low IQ, Dual, 2-Phase Synchronous Step-Down DC/DC Controller Features: Wide VIN Range: 4.5V to 60V (65V Abs Max) Wide Output Voltage Range: 0.8V ≤ VOUT ≤ 99% • VIN Adjustable Gate Drive Level 5V to 10V (OPTI-DRIVE) No External Bootstrap Diodes Required Low Operating IQ: 29μA (One Channel On) Selectable Gate Drive UVLO Thresholds Out-of-Phase Operation Reduces Required Input Capacitance and Power Supply Induced Noise Phase-Lockable Frequency: 75kHz to 850kHz Selectable Continuous, Pulse Skipping or Low Ripple Burst Mode® Operation at Light Loads Selectable Current Limit (LTC3892/LTC3892-2) Very Low Dropout Operation: 99% Duty Cycle Power Good Output Voltage Monitors (LTC3892/LTC3892-2) Low Shutdown IQ: 3.6μA Small 32-Lead 5mm × 5mm QFN Package (LTC3892/LTC3892-2) or TSSOP Package (LTC3892-1)

High Efficiency, Secondary-Side Synchronous Forward Controller Features: Direct Flux Limit™ Guarantees No Saturation Fast and Accurate Average Current Limit Clean Start-Up Into Pre-Biased Output Secondary-Side Control for Fast Transient Response Simple, Self-Starting Architecture Synchronous MOSFET Reverse Current Limit PolyPhase® Operation Eases High-Power Design True Remote Sense Differential Amplifier Remote Sense Reverse Protection High Voltage Linear Regulator Controller Internal LDO Powers Gate Drive from VOUT Overtemperature/Overvoltage Protection Low Profile 4mm × 5mm QFN and Narrow 28-Lead SSOP Packages

10 Volt Precision Reference Series Features:Very High Accuracy: 10,000 Volts 2.5mV (L and U)Low Temperature Coefficient: 3ppm/CPerformance Guaranteed -55C to +125C10mA Output Current CapabilityLow NoiseShort Circuit ProtectedAvailable as /883B

High Precision, Impedance & Electrochemical Front End Features: Analog input 16-bit ADC with both 800 kSPS and 1.6 MSPS options Voltage, current, and impedance measurement capability Internal and external current and voltage channels Ultralow leakage switch matrix and input mux Input buffers and programmable gain amplifier Voltage DACs Dual output voltage DAC with an output range of 0.2 V to 2.4 V 12-bit VBIAS0 output to bias potentiostat 6-bit VZERO0 output to bias TIA Ultra low power: 1 µA 1 high speed, 12-bit DAC Output range to sensor: ±607 mV Programmable gain amplifier on output with gain settings of 2 and 0.05 Amplifiers, accelerators, and references 1 low power, low noise potentiostat amplifier suitable for potentiostat bias in electrochemical sensing 1 low noise, low power TIA, suitable for measuring sensor current output 50 pA to 3 mA range Programmable load and gain resistors for sensor output Analog hardware accelerators Digital waveform generator Receive filters Complex impedance measurement (DFT) engine 1 high speed TIA to handle wide bandwidth input signals from 0.015 Hz up to 200 kHz Digital waveform generator for generation of sinusoid and trapezoid waveforms 2.5 V and 1.82 V internal reference voltage sources System level power savings Fast power-up and power-down analog blocks for duty cycling Programmable AFE sequencer to minimize workload of host controller 6 kB SRAM to preprogram AFE sequences Ultra low power potentiostat channel: 6.5 µAof current consumption when powered on and all other blocks in hibernate mode Smart sensor synchronization and data collection Cycle accurate control of sensor measurement Sequencer controlled GPIOs On-chip peripherals SPI serial input/output Wake-up timer Interrupt controller Power 2.8 V to 3.6 V supply 1.82 V input/output compliant Power-on reset Hibernate mode with low power DAC and potentiostat amplifier powered up to maintain sensor bias Package and temperature range 3.6 mm × 4.2 mm, 56-ball WLCSP 7 mm × 7 mm, 48-lead LFCSP Fully specified for operating temperature range of −40°C to +85°C AD5940 and AD5941 fully specified for operating temperature range of −40°C to +85°C AD5941W fully specified for operating temperature range of −40°C to +105°C AEC-Q100 qualified for automotive applications

The ADM1169 Super Sequencer® is a configurable supervisory/ sequencing device that offers a single-chip solution for supply monitoring and sequencing in multiple supply systems. In addition to these functions, the ADM1169 integrates a 12-bit ADC and four 8-bit voltage output DACs. These circuits can be used to implement a closed-loop margining system that enables supply adjustment by altering either the feedback node or reference of a dc-to-dc converter using the DAC outputs. Supply margining can be performed with a minimum of external components. The margining loop can be used for in-circuit testing of a board during production (for example, to verify board functionality at –5% of nominal supplies), or it can be used dynamically to accurately control the output voltage of a dc-to-dc converter. The device also provides up to eight programmable inputs for monitoring undervoltage faults, overvoltage faults, or out-of-window faults on up to eight supplies. In addition, there are eight programmable outputs that can be used as logic enables. Six of these programmable outputs can also provide up to a 12 V output for driving the gate of an N-FET that can be placed in the path of a supply. The logical core of the device is a sequencing engine (SE). This state machine-based construction provides up to 63 different states. This design enables very flexible sequencing of the outputs, based on the condition of the inputs. A block of nonvolatile EEPROM is available that can be used to store user-defined information and may also be used to hold a number of fault records that are written by the sequencing engine defined by the user when a particular fault or sequence occurs. The ADM1169 is controlled via configuration data that can be programmed into an EEPROM. The entire configuration can be programmed using an intuitive GUI-based software package provided by Analog Devices, Inc.

The ADM1275 is a hot-swap controller that allows a circuit board to be removed from or inserted into a live backplane. It also features current and voltage readback via an integrated 12-bit analog-to-digital converter (ADC), accessed using a PMBus™ interface. The load current is measured using an internal current sense amplifier that measures the voltage across a sense resistor in the power path via the SENSE+ and SENSE− pins. A default limit of 20 mV is set, but this limit can be adjusted, if required, using a resistor divider network from the internal reference voltage to the ISET pin.The ADM1275 limits the current through the sense resistor by controlling the gate voltage of an external N-channel FET in the power path, via the GATE pin. The sense voltage—and, therefore, the load current—is maintained below the preset maximum. The ADM1275 protects the external FET by limiting the time that the FET remains on while the current is at its maximum value. This current limit time is set by the choice of capacitor connected to the TIMER pin. In addition, a foldback resistor network can be used to actively lower the current limit as the voltage across the FET is increased. This helps to maintain constant power in the FET and allows the safe operating area (SOA) to be adhered to in an effective manner.In case of a short-circuit event, a fast internal overcurrent detector responds within 370 ns and signals the gate to shut down. A 1500 mA pull-down device ensures a fast FET response. The ADM1275 features overvoltage and undervoltage protection, programmed using external resistor dividers on the UV and OV pins. A PWRGD signal can be used to detect when the output supply is valid, using the FLB pin to monitor the output. GPO pins can be configured as various output signals that can be asserted when a programmed current or voltage level is reached.The 12-bit ADC can measure the current in the sense resistor, as well as the supply voltage on the SENSE+ pin or the output voltage. A PMBus interface allows a controller to read current and voltage data from the ADC. Measurements can be initiated by a PMBus command. Alternatively, the ADC can run continuously, and the user can read the latest conversion data whenever required. Up to four unique PMBus addresses can be selected, depending on the way that the ADR pin is connected. The ADM1275-1 and ADM1275-3 are available in a 20-lead QSOP and 20-lead LFCSP and have a LATCH pin that can be configured for automatic retry or latch-off when an overcurrent fault occurs. The ADM1275-2 is available in a 16-lead QSOP with latch-off mode only.Applications Power monitoring and control/power budgeting Central office equipment Telecommunication and data communication equipment PCs/servers

The ADM6326/ADM6328/ADM6346/ADM6348 devices provide low cost solutions for protecting sensitive circuitry, such as micro-processor and telecommunications circuitry.With built-in glitch immunity, ultralow supply currents, and 24 reset threshold voltage options, the ADM6326/ADM6328/ADM6346/ADM6348 not only ensure that systems are immune to fast transients on VCC, but also that the devices are suitable for monitoring a variety of supply voltages in low power, portable equipment.These devices provide a reset output during power-up, power-down, and brownout conditions. On power-up, an internal timer holds RESET asserted for at least 100 ms. This holds the microprocessor in a reset state until conditions have stabilized. The reset output remains operational with VCC as low as 1 V.The ADM6326 and ADM6346 have an active low push-pull reset output. The ADM6328 and ADM6348 have an active low open-drain reset output, which requires an external pull-up resistor. The ADM6326 and ADM6328 offer a choice of ten reset thresholds in increments between 2.2 V and 3.08 V, whereas the ADM6346 and ADM6348 offer a choice of 14 reset thresholds between 3.3 V and 4.63 V. Not all options are released for sale as standard models. See the Ordering Guide for details.These devices are available in a 3-lead SOT-23 package and operate over the extended temperature range of −40°C to +85°C.Applications Telecommunications Microprocessor systems Desktop and notebook computers Portable equipment

The ADM6326/ADM6328/ADM6346/ADM6348 devices provide low cost solutions for protecting sensitive circuitry, such as micro-processor and telecommunications circuitry.With built-in glitch immunity, ultralow supply currents, and 24 reset threshold voltage options, the ADM6326/ADM6328/ADM6346/ADM6348 not only ensure that systems are immune to fast transients on VCC, but also that the devices are suitable for monitoring a variety of supply voltages in low power, portable equipment.These devices provide a reset output during power-up, power-down, and brownout conditions. On power-up, an internal timer holds RESET asserted for at least 100 ms. This holds the microprocessor in a reset state until conditions have stabilized. The reset output remains operational with VCC as low as 1 V.The ADM6326 and ADM6346 have an active low push-pull reset output. The ADM6328 and ADM6348 have an active low open-drain reset output, which requires an external pull-up resistor. The ADM6326 and ADM6328 offer a choice of ten reset thresholds in increments between 2.2 V and 3.08 V, whereas the ADM6346 and ADM6348 offer a choice of 14 reset thresholds between 3.3 V and 4.63 V. Not all options are released for sale as standard models. See the Ordering Guide for details.These devices are available in a 3-lead SOT-23 package and operate over the extended temperature range of −40°C to +85°C.Applications Telecommunications Microprocessor systems Desktop and notebook computers Portable equipment