The ADG601 / ADG602 are monolithic, CMOS single-pole single-throw (SPST) switches with on resistance typically less than 2.5 Ω. The low on-resistance flatness makes the ADG601 / ADG602 ideally suited to many applications, particularly those requiring low distortion. These switches are ideal replacements for mechanical relays because they are more reliable, have lower power requirements, and are available in much smaller package sizes.The ADG601 is a normally open (NO) switch, and the ADG602 is a normally closed (NC) switch. Each switch conducts equally well in both directions when the device is on, with the input signal range extending to the supply rails.The switches are available in tiny, 6-lead SOT-23; 8-lead MSOP; and 820 μm × 2255 μm die.PRODUCT HIGHLIGHTS Low on resistance (2 Ω typical) Dual ±2.7 V to ±5.5 V or single +2.7 V to +5.5 V supplies Tiny, 6-lead SOT-23; 8-lead MSOP; and 820 μm × 2255 μm die Rail-to-rail input signal rangeAPPLICATIONS Automatic test equipment Power routing Communication systems Data acquisition systems Sample-and-hold systems Avionics Relay replacement Battery-powered systems

The ADG609 is a monolithic CMOS analog multiplexer comprising four differential channels. The ADG609 switches one of four differential inputs to a common differential output as determined by the 2-bit binary address lines A0 and A1. An EN input on both devices is used to enable or disable the device. When disabled, all channels are switched OFF.The ADG609 is designed on an enhanced LC2 MOS process which provides low power dissipation yet gives high switching speed and low on resistance. Each channel conducts equally well in both directions when ON and has an input signal range which extends to the supplies. In the OFF condition, signal levels up to the supplies are blocked. All channels exhibit break before make switching action preventing momentary shorting when switching channels. Inherent in the design is low charge injection for minimum transients when switching the digital inputs.

The ADV3221  and ADV3222 are high speed, high slew rate, buffered 4:1 analog multiplexers. They offer a −3 dB signal bandwidth greater than 800 MHz and channel switch times of less than 20 ns with 1% settling. With lower than −58 dB of crosstalk and −67 dB isolation (at 100 MHz), the ADV3221 and ADV3222 are useful in many high speed applications. The differential gain error of less than 0.02% and differential phase error of less than 0.02°, together with 0.1 dB gain flatness out to 100 MHz while driving a 75 Ω back terminated load, make the ADV3221 and ADV3222 ideal for all types of signal switching.The ADV3221/ADV3222 include an output buffer that can be placed into a high impedance state. This allows multiple outputs to be connected together for cascading stages without the off channels loading the output bus. The ADV3221 has a gain of +1, and the ADV3222 has a gain of +2; they both operate on ±5 V supplies while consuming less than 7.5 mA of idle current. The channel switching is performed via latched control lines, allowing synchronous updating in a multiple ADV3221/ADV3222 envi-ronment.The ADV3221/ADV3222 are offered in a 16-lead SOIC package and are available over the extended industrial temperature range of −40°C to +85°C.Applications Routing of high speed signals including     Video (NTSC, PAL, S, SECAM, YUV, RGB)     Compressed video (MPEG, wavelet)     3-level digital video (HDB3)     Data communications     Telecommunications

RF Switch ICs SP4T Non-Reflective Switch , DC - 8 GHz

FAILSAFE SWITCH, SPST, 6GHZ, SOT-26;

FAILSAFE SWITCH, SPST, 6GHZ, SOT-26;

RF Switch ICs 40W SPDT Failsafe Switch , 0.1 - 2.1 GHz

Multiplexer Switch ICs LC2MOS +/-15V 4 Ch High Per Multiplex IC

Silicon SPDT Switch, Reflective, 9 kHz to 44 GHz Features: Ultrawideband frequency range: 9 kHz to 44 GHz Reflective design Low insertion loss with impedance match 0.9 dB typical to 18 GHz 1.4 dB typical to 40 GHz 1.6 dB typical to 44 GHz Low insertion loss without impedance match 0.9 dB typical to 18 GHz 1.7 dB typical to 40 GHz 2.2 dB typical to 44 GHz High input linearity P1dB: 27.5 dBm typical IP3: 50 dBm typical High RF input power handling Through path: 27 dBm Hot switching: 27 dBm No low frequency spurious RF settling time (50% VCTL to 0.1 dB final RF output): 3.4 μs 12-terminal, 2.25 mm × 2.25 mm LGA package Pin compatible with the ADRF5024 fast switching version

Silicon SPDT Switch, Reflective, 9 kHz to 44 GHz Features: Ultrawideband frequency range: 9 kHz to 44 GHz Reflective design Low insertion loss with impedance match 0.9 dB typical to 18 GHz 1.4 dB typical to 40 GHz 1.6 dB typical to 44 GHz Low insertion loss without impedance match 0.9 dB typical to 18 GHz 1.7 dB typical to 40 GHz 2.2 dB typical to 44 GHz High input linearity P1dB: 27.5 dBm typical IP3: 50 dBm typical High RF input power handling Through path: 27 dBm Hot switching: 27 dBm No low frequency spurious RF settling time (50% VCTL to 0.1 dB final RF output): 3.4 μs 12-terminal, 2.25 mm × 2.25 mm LGA package Pin compatible with the ADRF5024 fast switching version