Bridge Sensor Signal Conditioner IC with LIN Interface, Nonlinearity Correction, Temperature Compensation Features:LIN 2.1 compliant interface (bridge sensor signal, temperature)Digitally programmable gain and offset voltage adjustmentGain range from 2.94 V/V to 971.10 V/VSensor temperature compensation (first- or second-order)Sensor nonlinearity correction (first- or second-order)Internal or external temperature sensor compensationEEPROM nonvolatile memory for calibration dataHigh system accuracy: 0.1% FSR over temperatureEMC and EMI protectionFault protection for open circuits and short circuits4 mm 4 mm, 20-lead LFCSP6 V to 18 V supply operation40C to +150C operating temperature rangeAEC-Q100 qualified for automotive applications

16-Bit, 15 MSPS, Module Data Acquisition Solution Features: Integrated fully differential ADC driver with signal scaling Wide input common range High common-mode rejection Single-ended to differential conversion 2.048 V input range with 4.096 V REFBUF Critical passive components 0.005% precision matched resistor array for FDA 9 mm × 9 mm, 0.8 mm pitch, 100-ball BGA package 4× footprint reduction versus discrete solution Low power, dynamic power scaling, power-down mode 143 mW typical at 15 MSPS Throughput: 15 MSPS, no pipeline delay INL: 0.4 LSB typical, 1 LSB maximum SINAD: 89 dB typical at 1 kHz THD: 115 dB at 1 kHz, 106 dB at 400 kHz Gain error: 0.005% FS typical Gain error drift: 1 ppm/C maximum On-board reference buffer with VCMO generation Serial LVDS interface Wide operating temperature range: 40C to +85C

18-Bit, 15 MSPS, Module Data Acquisition Solution Features: Integrated fully differential ADC driver with signal scaling Wide input common-mode voltage range High common-mode rejection Single-ended to differential conversion Pin selectable input range with overrange Input ranges with 4.096 V REFBUF: ±10 V, ±5 V, ±4.096 V, ±2.5 V, and ±1.5 V Gain/attenuation options: 0.37, 0.73, 0.87, 1.38, and 2.25 Critical passive components 0.005% precision matched resistor array for FDA 9 mm × 9 mm, 0.8 mm pitch, 100-ball CSP_BGA package 2.5× footprint reduction vs. discrete solution Low power, dynamic power scaling, power-down mode 143 mW typical at 15 MSPS Throughput: 15 MSPS, no pipeline delay INL error: ±3.1 ppm typical, ±6.2 ppm maximum (Gain = 0.73, gain = 0.87, gain = 1.38, gain = 2.25) SINAD: 90.4 dB typical at 20 kHz (gain = 0.73) THD: −117 dB at 1 kHz, −110 dB at 100 kHz (gain = 0.73) Gain error: ±0.005%FS typical Gain error drift: ±0.13 ppm/°C typical On-board reference buffer with VCMO generation Serial LVDS interface Wide operating temperature range: −40°C to +85°C

Three ADCs, One DAC, Low Power Codec with Audio DSPs Features: Programmable FastDSP audio processing engine Up to 768 kHz sample rate Biquad filters, limiters, volume controls, mixing Tensilica HiFi 3z DSP core Quad MAC per cycle: 24 x 24-bit multiplier and 64-bit accumulator Flexible power operation mode: 24.576 MHz, 49.152 MHz, 73.728 MHz, and 98.304 MHz 336 kB total memory JTAG debug and trace Low latency, 24-bit ADCs and DAC 106 dB SNR (signal through ADC with A-weighted filter) 110 dB combined SNR (signal through DAC and headphone with A-weighted filter) Programmable double precision MAC engine for maximum 24-stage equalizer Serial port sample rates from 8 kHz to 768 kHz 5 μs group delay (fS = 768 kHz) analog in to analog out with FastDSP bypass (zero instructions) 3 differential or single-ended analog inputs, configurable as microphone or line inputs 8 digital microphone inputs Analog differential audio output, configurable as either line output or headphone drive 2 PDM output channels PLL supporting any input clock rate from 30 kHz to 36 MHz 4 channel asynchronous sample rate converters (ASRCs) 2, 16-channel serial audio ports supporting I2S, left justified, right justified, or up to TDM16 (TDM12 in Turbo mode) 8 interpolators and 8 decimators with flexible routing Power supplies Analog AVDD at 1.8 V typical Digital I/O IOVDD at 1.1 V to 1.98 V Digital DVDD at 0.85 V to 1.21 V Headphone HPVDD at 1.8 V typical Headphone HPVDD_L at 1.2 V to HPVDD Control/communication interfaces I2C, SPI, or UART control ports Master quad SPI (QSPI) UART communication port Self-boot from QSPI flash Flexible GPIO and IRQ 56-ball, 0.35 mm pitch, 2.980 mm × 2.679 mm WLCSP

8 Channel, PDM to I2S/TDM Converter Features: 8 channels of PDM audio inputs from digital microphones 16×, 32×, or 64× decimation ratio of PDM to PCM audio data 24-bit resolution to support high sound pressure level (SPL) microphones 126 dB A-weighted SNR 4 kHz to 192 kHz output sampling rate Bit clock rates of 64×, 128×, 192×, 256×, 384×, or 512× the output sampling rate Dual output PDM clocks Automatic PDM clock generation Automatic power-down when BCLK removed Selectable I2C control or hardware mode operation 1.2 mA DVDD operating current for 8 channels at 48 kHz frequency sampling rate and 1.8 V supply Slave I2S or TDM output interface Up to TDM-16 supported Configurable TDM slot routing and sizes I/O supply voltage from 1.70 V to 3.63 V DVDD supply voltage from 1.10 V to 1.98 V <5 μA typical DVDD shutdown current 16-lead, 3 mm × 3 mm, 0.50 mm pitch LFCSP Power-on reset

18-Cell Battery Monitor with Daisy Chain Interface Features: Measures up to 18 battery cells in series 3 mV maximum total measurement error Stackable architecture for high voltage systems Built-in isoSPI interface 1 Mb isolated serial communications Uses a single twisted pair, up to 100 meters Low EMI susceptibility and emissions Bidirectional for broken wire protection 290 μs to measure all cells in a system Synchronized voltage and current measurement 16-bit Δ-Σ ADC with programmable third-order noise filter Passive cell balancing up to 200 mA (maximum) with programmable pulsewidth modulation 9 general purpose digital I/O or analog inputs Temperature or other sensor inputs Configurable as an I2C or SPI master 6 μA sleep mode supply current 64-lead LQFP_EP package

Ultrafast SiGe Voltage Comparator (Featuring Reduced Swing PECL Output Drivers) Features: 180 ps propagation delay 25 ps overdrive and slew rate dispersion 8 GHz equivalent input rise time bandwidth 100 ps minimum pulse width 37 ps typical output rise/fall 10 ps deterministic jitter (DJ) 200 fs random jitter (RJ) −2 V to +3 V input range with +5 V/−5 V supplies On-chip terminations at both input pins Resistor-programmable hysteresis Differential latch control Power supply rejection > 70 dB

Dual Channel, Configurable, IsolatedDigital Input Features: Dual channel, configurable, isolated digital input Programmable trip threshold On-chip debounce filter On-chip data and power Isolation Application circuit monitors wide voltage range 10 V dc to 300 V dc 8 V rms to 240 V rms ac (with 10 ms + pickup) Negative dc protected Programmable wetting current Pulse up to 50 mA Constant current up to 6.3 mA Safety and regulatory approvals UL recognition 3750 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice #5A (pending) CSA 61010-1: 300 V rms VDE certificate of conformity (pending) DIN V VDE V 0884-11 (VDE V 0884-11):2017-1 VIORM = 565 V peak EMC robust solution supports relay protection system level requirements ADC samples available for system diagnostics Internal SAR ADC with PGA Single 3.3 V Supply Integrated isoPower, isolated dc-to-dc converter Interfaces SPI DOUTx output reflects state of digital input IRQ interrupt pin Operating temperature: −40°C to +125°C 20-lead, LGA package with 6.8 mm creepage

High Performance Polyphase Energy Measurement IC Features: 7 high performance analog-to-digital converters (ADCs) 101 dB signal-to-noise ratio (SNR) 10,000:1 dynamic range Wide input range: ±1 V, 0.707 V rms full scale Differential inputs ±25 ppm/°C maximum channel temperature drift (including ADC, internal VREF, and PGA drift) enabling Class 0.2 meters with standard external components Power quality measurements Line frequency: 1 measurement per phase Zero crossing detection, zero-crossing timeout Phase angle measurements Supports current transformers (CTs) and Rogowski coil (di/dt) sensors Multiple range phase/gain compensation for CTs Digital integrator for Rogowski coils Flexible waveform buffer Able to resample waveform to ensure 64 points per line cycle for ease of external harmonic analysis Events can trigger waveform storage Simplifies data collection for IEC 61000-4-7 harmonic analysis Advanced metrology feature set Total active power, volt-amperes reactive (VAR), volt-amperes (VA), watthour, VAR-hour, and VA-hour Fundamental VAR and VAR-hour Current and voltage rms per phase (xIRMS, xVRMS) Supports active energy standards: IEC 62053-21, IEC 62053-22; EN50470-3; OIML R46, ANSI C12.20 Supports reactive energy standards: IEC 62053-23, IEC 62053-4 High speed communication port 10 MHz serial peripheral interface (SPI)

User Defined Fault Protection and Detection, 0.8 pC QINJ, 8:1 Multiplexer Features: User defined secondary supplies set overvoltage level Overvoltage protection up to −55 V and +55 V Power-off protection up to −55 V and +55 V Overvoltage detection on source pins Minimum secondary supply level: 4.5 V single-supply Interrupt flags indicate fault status Low charge injection (QINJ): 0.8 pC Low drain/source on capacitance: 19 pF Latch-up immune under any circumstance Known state without digital inputs present VSS to VDD analog signal range ±5 V to ±22 V dual-supply operation 8V to 44 V single-supply operation Fully specified at ±15 V, ±20 V, +12 V, and +36 V