16-Channel 50mA LED Driver with Buck Controller Features: 6V to 55V Power Input Voltage Range 16 Independent LED Outputs Up to 75mA/36V ±3% LED Current Matching at 50mA (Typ ±1%) 6-Bit Dot Correction Current Adjustment 12-Bit Grayscale PWM Dimming 0.5μs Minimum LED On-Time Adaptive LED Bus Voltage for High Efficiency Cascadable 30MHz Serial Data Interface Full Diagnostic and Protection: Individual Open/Short LED and Overtemperature Fault 40-Lead 6mm × 6mm QFN Package

Dual Ideal Diode and Single Hot Swap Controller Features: Power Path and Inrush Current Control for Redundant Supplies Low Loss Replacement for Power Schottky Diodes Allows Safe Hot Swapping from a Live Backplane 2.9V to 18V Operating Range Controls N-Channel MOSFETs Limits Peak Fault Current in ≤1μs 0.5μs Ideal Diode Turn-On and Reverse Turn-Off Time Adjustable Current Limit with Circuit Breaker Smooth Switchover without Oscillation Adjustable Current Limit Fault Delay Fault and Power Status Output 20-Lead 4mm × 5mm QFN and 16-Lead SSOP Packages

Dual Ideal Diode and Single Hot Swap Controller Features: Power Path and Inrush Current Control for Redundant Supplies Low Loss Replacement for Power Schottky Diodes Allows Safe Hot Swapping from a Live Backplane 2.9V to 18V Operating Range Controls N-Channel MOSFETs Limits Peak Fault Current in ≤1μs 0.5μs Ideal Diode Turn-On and Reverse Turn-Off Time Adjustable Current Limit with Circuit Breaker Smooth Switchover without Oscillation Adjustable Current Limit Fault Delay Fault and Power Status Output 20-Lead 4mm × 5mm QFN and 16-Lead SSOP Packages

Dual Ideal Diode and Single Hot Swap Controller Features: Power Path and Inrush Current Control for Redundant Supplies Low Loss Replacement for Power Schottky Diodes Allows Safe Hot Swapping from a Live Backplane 2.9V to 18V Operating Range Controls N-Channel MOSFETs Limits Peak Fault Current in ≤1μs 0.5μs Ideal Diode Turn-On and Reverse Turn-Off Time Adjustable Current Limit with Circuit Breaker Smooth Switchover without Oscillation Adjustable Current Limit Fault Delay Fault and Power Status Output 20-Lead 4mm × 5mm QFN and 16-Lead SSOP Packages

Programmable Hex Voltage Supervisor with EEPROM Features: Supervises 6 Power Supplies I2C Adjustable UV and OV Trip Points Guaranteed Threshold Accuracy: ±1% I2C/SMBus Interface Internal EEPROM 256 Programmable Thresholds per Channel Up to Three Range Settings per Channel Two General Purpose Inputs Three General Purpose Inputs/Outputs Programmable Output Delays Supply Voltage Range, 3.4V to 13.9V Supply Voltage Power Sharing from V1 to V4 16-Lead 5mm × 4mm DFN and SSOP Packages

UltraFast 7ns Response Time 15GHz RF Power Detector with Comparator Features: Temperature Compensated Schottky RF Peak Detector Wide Input Frequency Range: 600MHz to 15GHz† Wide Input Power Range: –24dBm to 16dBm 7ns Typical Response Time 75MHz Demodulation Bandwidth Programmable Gain Settings for Improved Sensitivity Adjustable Amplifier Output Offset Voltage High Speed Comparator with Latch Enable: 9ns Typical Response Time 16-Lead 3mm × 3mm QFN Package Temperature Range: –40°C to 125°C†Higher frequency operation is achievable with reduced performance. Consult the factory formore information.

20V High Efficiency Nanopower Step-Down Regulator Features: 720nA Input IQ in Regulation (No Load), VIN = 4V 820nA Input IQ in Regulation (No Load), VIN = 20V 400nA Input IQ in UVLO 2.7V to 20V Input Operating Range Up to 50mA of Output Current Pin Selectable Output Voltages: 1.2V, 1.5V, 1.8V, 2.5V (LTC3388-1) 2.8V, 3.0V, 3.3V, 5.0V (LTC3388-3) High Efficiency Hysteretic Synchronous DC/DC Conversion Standby Mode Disables Buck Switching Available in 10-Lead MSE and 3mm × 3mm DFN Packages

Dual Low Power, High Speed JFET Operational Amplifier Features: Low supply current: 250 μA/amp maximum High slew rate: 9 V/μs Bandwidth: 3.5 MHz typical Low offset voltage: 1 mV maximum @ 25°C Low input bias current: 20 pA maximum @ 25°C CMRR: 90 dB typical Fast settling time Unity gain stable

Low Input Bias Current, Wide BW JFET Precision Dual Op Amp Features: Low Noise 6 nV/√Hz Low Offset Voltage: 100 µV Max Low Input Bias Current 10 pA Max Fast Settling: 600 ns to 0.01% Low Distortion Unity Gain Stable No Phase Reversal Dual-Supply Operation: ±5 V to ±13 V

Anyside High Voltage Isolated Switch Controller with I2C Command and Telemetry Features: CSA (IEC/UL) Approved, File #255632 Reinforced Insulation Integrated Isolated Power Supply Adjustable Turn-On Ramp Rate and Current Limit I2C/SMBus Interface 10-Bit ADC Monitors Current and Two Uncommitted Channels High Common Mode Transient Immunity: ≥ 30kV/μs Fault Status Alert and Power Good Outputs Independent 3V to 5.5V Logic Supply ±20kV ESD Across the Isolation Barrier Maximum Continuous Working Voltage: 690VRMS 14.6mm Creepage Distance Low Current Shutdown Mode (<10μA) 22mm × 9mm × 5.16mm BGA Package