1 MSPS, 14-Bit, Simultaneous Sampling SAR ADC with PGA and Four Comparators Features: Dual, simultaneous sampling, 14-bit, 2-channel ADC True differential analog inputs Programmable gain stage: ×1, ×2, ×3, ×4, ×6, ×8, ×12, ×16, ×24, ×32, ×48, ×64, ×96, ×128 Throughput rate per ADC 1 MSPS for AD7264 Analog input impedance: >1 GΩ Wide input bandwidth −3 dB bandwidth: 1.7 MHz at gain = 2 4 on-chip comparators SNR: 78 dB typical at gain = 2, 71 dB typical at gain = 32 Device offset calibration System gain calibration On-chip reference: 2.5 V −40°C to +105°C operation High speed serial interface Compatible with SPI, QSPI™, MICROWIRE™, and DSP 48-lead LFCSP and LQFP packages

+3/+5 Volt Serial-Input Micropower 10-Bit DAC Features: Micropower - 100 µA Single Supply - 2.7 V to 5.5 V Operation Compact 1.75 mm Height SO-8 Package and 1.1 mm Height TSSOP-8 Package AD7390 - 12-Bit Resolution AD7391 - 10-Bit Resolution SPI and QSPI Serial Interface Compatible with Schmitt Trigger Inputs

2.7 V to 5.5 V, Serial-Input, Voltage-Output, 16-Bit nanoDAC in 10-lead LFCSP, 16-lead 3 mm x 3 mm LFCSP, and 16-lead TSSOP Features: 12-/16-bit resolution 1 LSB INL 11.8 nV/√Hz noise spectral density 1 μs settling time 1.1 nV-sec glitch energy 0.05 ppm/°C temperature drift 5 kV HBM ESD classification See data sheet for additional features Also available in16-lead TSSOP

Precision Wide-range (3 nA - 3 mA) High-Side Current Mirror Features: Accurately mirrors input current (1:1 ratio) over 6 decades - enables monitoring at low signal levels  Linearity 1% from 3 nA to 3 mA Stable mirror input voltage Voltage held 1 V below supply using internal reference or may be set externally providing greater flexibility in design Adjustable input current limit provides protection to the connected photodiode 2.7 V to 8 V single-supply operation Miniature 8-lead chip scale package (LFCSP 2 mm × 3 mm) saves valuable board space

10 MHz TO 10 GHz 67 dB TruPwr Detector Features: Accurate rms-to-dc conversion from 10 MHz to 10 GHz Single-ended ±1 dB dynamic range: 67 dB at 2.14 GHz    No balun or external input matching required Response independent of waveform types, such as GSM/CDMA/W-CDMA/TD-SCDMA/WiMAX/LTE Logarithmic slope: 55 mV/dB Temperature stability: <±1 dB from −40°C to +125°C Operating temperature: −55°C to +125°C Supply voltage: 4.75 V to 5.25 V Sleep current: 250 µA Pin-compatible with ADL5902 and AD8363

Microprocessor Supervisory in SOT-23 with Active High and Low Push-Pull Output Features: Reliable Low Cost Voltage Monitor with Reset Output Suitable for Monitoring 2.5 V, 3 V, 3.3 V, and 5 V Power Supply Voltages Reset Threshold Levels: 4.62 V, 4.35 V, 3.06 V, 2.88 V, 2.55 V, 2.31 V, and 2.18 V (Typ)Initialize Microprocessor Systems with Added Safety Open-Drain Output Choices (ADM1811, ADM1813, ADM1816, and ADM1818) Can Be Used with a Manual Push-Button to Generate a Reset (ADM1813, ADM1818) Available in 3-Lead SOT-23 and SC70 Packages Active High and Low Push-Pull Output Choices (ADM1810, ADM1812, ADM1815, and ADM1817)

High Speed, 5 V, 0.1 F CMOS RS-232 Driver/Receiver Features: 120 kB transmission rate Small (0.1 µF) charge pump capacitors Single 5 V power supply Meets TIA/EIA-232-E and V.28 specifications 2 drivers and 2 receivers On-board dc-to-dc converters ±9 V output swing with 5 V supply Low power BiCMOS: 2.5 mA ICC ±30 V receiver input levels

Equalisers Front Panel HDMI Buffer - TMDS Only

Operational Amplifiers - Op Amps VLTG-FDBK, G= 2 CLAMP AMP

Charge Pump, 7-Channel Smart LED Driver with I2C Interface Features: Charge pump with automatic gain selection of 1×, 1.5×, and 2× for maximum efficiency 7 independent, programmable LED drivers 7 drivers capable of 30 mA (typical) 1 driver also capable of 60 mA (typical) Programmable maximum current limit (128 levels) Standby mode for <1 μA current consumption 16 programmable fade in and fade out time 0.1 sec to 5.5 sec Choose from linear, square, or cubic rates Fading override I2C-compatible interface for all programming Dedicated reset pin and built-in power-on reset (POR) Short-circuit, overvoltage, and overtemperature protection Internal soft start to limit inrush currents Input-to-output isolation during faults or shutdown Operation down to VIN = 2.5 V with undervoltage lockout (UVLO) at VIN = 2.0 V Available in a small 20-ball, 2.15 mm × 2.36 mm × 0.6 mm WLCSP or a 20-lead, 4 mm × 4 mm × 0.75 mm LFCSP