9 GHz to 12 GHz, GaAs, MMIC, I/Q Downconverter Features: Conversion gain: 11 dB (typical) at IFOUT = 100 MHz Image rejection: 25 dB (typical) at IFOUT = 100 MHz LO to RF isolation: 46 dB (typical) LO to IF isolation: 26 dB (typical) IF output frequency: dc to 3.5 GHz 32-lead, 4.9 mm × 4.9 mm ceramic leadless chip carrier

5.6 GHz to 8.6 GHz, GaAs, MMIC, I/Q Downconverter Features: Conversion gain: 13 dB typical Image rejection: 32 dBc typical Input P1dB compression: −6 dBm typical Input IP3: 3 dBm typical, 6.0 GHz to 8.6 GHz Noise figure: 2 dB typical LO to RF isolation: 48 dBm typical LO to IF isolation: 13 dBm typical RF to IF isolation: 10 dBm typical Amplitude balance: 0.2 dB typical Phase balance: −2° typical RF return loss: 10 dB typical LO return loss: 15 dB typical IF return loss: 15 dB typical Exposed paddle, 4 mm × 4 mm, 24-lead, LFCSP

Quad-Channel, Software Configurable Input and Output Features: Quad-channel software configurable input/output circuit Screw terminals tolerant to ±40 V dc Line protectors to block power from the screw terminals to supplies User configurable modes Voltage input Current input Voltage output Current output Digital input RTD measurement Internal 16-bit, Σ- ADC with optional 50 Hz and 60 Hz rejection 13-bit monotonic DACs Charge pump for true zero voltage output HART-compatible Internal temperature sensor, ±5°C accuracy On-chip diagnostics including open circuit and short-circuit detection SPI-compatible Temperature range: −40°C to +105°C 64-lead LFCSP

High Performance, Multiphase Energy, and Power Quality Measurement IC Features: 7 high performance ADCs 101 dB SNR Wide input voltage range: ±1 V, 707 mV rms FS at gain = 1 Differential inputs ±25 ppm/°C maximum channel drift (including ADC, internal VREF, PGA drift) enabling 10000:1 dynamic input range Class 0.2 metrology with standard external components Power quality measurements Enables implementation of IEC 61000-4-30 Class S VRMS ½, IRMS ½ rms voltage refreshed each half cycle 10 cycle rms/12 cycle rms Dip and swell monitors Line frequency—one per phase Zero crossing, zero-crossing timeout Phase angle measurements Supports CTs and Rogowski coil (di/dt) sensors Multiple range phase/gain compensation for CTs Digital integrator for Rogowski coils Flexible waveform buffer Able to resample waveform to ensure 128 points per line cycle for ease of external harmonic analysis Events, such as dip and swell, can trigger waveform storage Simplifies data collection for IEC 61000-4-7 harmonic analysis Advanced metrology feature set Total and fundamental active power, volt amperes reactive (VAR), volt amperes (VA), watthour, VAR hour, and VA hour Total and fundamental IRMS, VRMS Total harmonic distortion Power factor Supports active energy standards: IEC 62053-21 and IEC 62053-22; EN50470-3; OIML R46; and ANSI C12.20 Supports reactive energy standards: IEC 62053-23, IEC 62053-24 High speed communication port: 20 MHz serial port interface (SPI) Integrated temperature sensor with 12-bit successive approximation register (SAR) ADC ±3°C accuracy from −40°C to +85°C

9.85 GHz to 20.5 GHz, Wideband, MMIC VCO Features: Wide output frequency range: 9.85 GHz to 20.5 GHz Wide tuning bandwidth Low single sideband phase noise: −83 dBc/Hz at 100 kHz offset No external resonator needed Supply current: 70 mA typical at VCC = 5 V 24-terminal, 3.90 mm × 3.90 mm, ceramic LCC package

Dual Channel, 16-Bit, 33 MUPS, Multispan, Multi-IO SPI DAC Features: 16-bit resolution 33 MUPS single channel rate in fast mode 22 MUPS single channel rate in precision mode 65 ns small signal settling time to 0.1% accuracy 100ns large signal settling time to 0.1% accuracy Ultra small glitch: < 50 pV×s Ultra low latency: 5 ns THD: −105 dB at 1 kHz Highly configurable output voltage span and offset 1.2 V and 1.8 V logic level compatible Single (classic), dual, and quad SPI modes Multiple error detectors, both analog and digital domains 2.5 V internal voltage reference, 10 ppm/°C maximum temperature coefficient 5 mm × 5 mm LFCSP

16-Bit, 2 MSPS/1 MSPS, Precision, Differential SAR ADCs Features: Easy Drive Greatly reduced input kickback Input current reduced to 0.5 μA/MSPS Enhanced acquisition phase, ≥79% of cycle time at 1 MSPS First conversion accurate, no latency or pipeline delay Input span compression for single-supply operation Fast conversion allows low SPI clock rates Input overvoltage clamp protection sinks up to 50 mA SPI-/QSPI-/MICROWIRE-/DSP-compatible serial interface High performance Differential analog input range: ±VREF, VREF from 2.4 V to 5.1 V Throughput: 2 MSPS/1 MSPS options INL: ±0.4 LSB maximum Guaranteed 16-bit, no missing codes SNR: 96.2 dB at fIN = 1 kHz, VREF = 5 V THD: −123 dB at fIN = 1 kHz, −99 dB at fIN = 100 kHz SINAD: 88.5 dB at fIN = 1 MHz (see Figure 17 in data sheet) Oversampled dynamic range 99.3 dB for OSR = 2 126 dB for OSR = 1024 Low power Single 1.8 V supply operation with 1.71 V to 5.5 V logic interface 4.9 mW at 1 MSPS (VDD only) 80 μW at 10 kSPS, 16 mW at 2 MSPS (total power) 10-lead packages: 3 mm × 3 mm LFCSP, 3 mm × 4.90 mm MSOP Pin compatible with AD4003/AD4007/AD4011 family Guaranteed operation: −40°C to +125°C

18-Bit, 2 MSPS/1 MSPS/500 kSPS, Precision, Pseudo Differential, SAR ADCs Features: Easy Drive Greatly reduced input kickback Input current reduced to 0.5 μA/MSPS Enhanced acquisition phase, ≥79% of cycle time at 1 MSPS First conversion accurate, no latency or pipeline delay Input span compression for single-supply operation Fast conversion allows low SPI clock rates Input overvoltage clamp protection sinks up to 50 mA SPI-/QSPI-/MICROWIRE-/DSP-compatible serial interface High performance Pseudo differential analog input range 0 V to VREF with VREF from 2.4 V to 5.1 V Throughput: 2 MSPS/1 MSPS/500 kSPS options INL: ±3.2 LSB maximum Guaranteed 18-bit, no missing codes SNR: 95 dB at fIN = 1 kHz at VREF = 5 V THD: −125 dB at fIN = 1 kHz, −108 dB at fIN = 100 kHz SINAD: 84.5 dB at fIN = 1 MHz (see Figure 17 in data sheet) Oversampled dynamic range 98 dB for OSR = 2 125 dB for OSR = 1024 Low power Single 1.8 V supply operation with 1.71 V to 5.5 V logic interface 2.5 mW at 500 kSPS (VDD only) 70 μW at 10 kSPS, 14 mW at 2 MSPS (total power) 10-lead packages: 3 mm × 3 mm LFCSP, 3 mm × 4.90 mm MSOP Pin compatible with AD4003/AD4007/AD4011 family Guaranteed operation: −40°C to +125°C

Single Supply, 24-Bit, Sigma-Delta ADC with 10 V and 0 mA to 20 mA Inputs Features: Internal or external clock Tested for robustness per: IEC61000-4-2, IEC61000-4-3, IEC61000-4-4, IEC61000-4-5, IEC61000-4-6, CISPR 11 24-bit ADC with integrated analog front end Fast and flexible output rate: 1.25 SPS to 31.25 kSPS Channel scan data rate of 6.21 kSPS per channel (161 μs settling) 16 noise free bits at 1 kSPS per channel 85 dB rejection of 50 Hz and 60 Hz at 20 SPS per channel ±10 V inputs, 4 differential or 8 single-ended Pin absolute maximum rating ±50 V Absolute input pin voltage up to ±20 V ≥1 MΩ impedance ±0.06% accuracy at 25°C 0 mA to 20 mA inputs, 4 single-ended Pin absolute maximum rating ±50 mA Input range from −0.5 mA to +24 mA 60 Ω impedance ±0.08% accuracy at 25°C On-chip 2.5 V reference ±0.12% accuracy at 25°C, ±5 ppm/°C (typical) drift Power supplies AVDD = 3.0 V to 5.5 V IOVDD = 2 V to 5.5 V Total IDD = 3.9 mA Temperature range: −40°C to +105°C 3-wire or 4-wire serial digital interface (Schmitt trigger on SCLK) SPI, QSPI, MICROWIRE, and DSP compatible

16-Bit, 16-Channel, 500 kSPS/1 MSPS, Easy Drive Multiplexed SAR ADC Features: Easy Drive Reduced analog input and reference drive requirements On-chip reference buffer (WLCSP only) Overvoltage protection up to 5 mA on each analog input Long acquisition phase, ≥71.5% (715 ns/1000 ns) of cycle time at 1 MSPS High performance Sample rate: 500 kSPS (AD4695) or 1 MSPS (AD4696) INL: ±1.0 LSB maximum Guaranteed 16-bit, no missing codes SINAD: 93 dB typical, fIN = 1 kHz Oversampled dynamic range: 111.2 dB, OSR = 64 Small footprint, high channel density 32-lead 5 mm × 5 mm LFCSP 36-ball 2.96 mm × 2.96 mm WLCSP Easy Drive features support system level designs with fewer components Enhanced digital functionality First conversion accurate, no latency or pipeline delay Fast conversion time and dual-/quad-SDO modes allow low SPI clock rates Customizable channel sequencer On-chip oversampling and decimation Threshold detection alerts Offset and gain correction Autonomous conversion (autocycle) mode 1.14 V to 1.98 V logic SPI Low power 8 mW at fS = 1 MSPS and 4 mW at fS = 500 kSPS 4 μW standby power dissipation with the internal LDO disabled Internal LDO enables 3.15 V to 5.5 V, single analog supply operation Wide operating temperature range: −40°C to +125°C