Low Complexity, 2-Port Ethernet Switch with Integrated 10BASE-T1L PHYs Features: 10BASE-T1L IEEE® Std 802.3cg-2019™ compliant Supports 1.0 V p-p & 2.4 V p-p transmit Levels Cable reach Up to 1700 meters with 1.0 V p-p transmit level Up to 1700 meters with 2.4 V p-p transmit level Low power consumption Low power consumption - single supply 80 mW typ Dual supply 1.0 V p-p: 77 mW typical Integrated switch with SPI interface 10 Mbps full duplex 16 MAC addresses supported for frame forwarding Supports OPEN Alliance 10BASE-T1x MACPHY SPI MDIO memory map accessible via SPI Supports high & low priority queues Total buffer memory of 28 kB shared between ports and host Autonegotiation capability Managed or unmanaged configuration Cut through or store and forward operation IEEE 1588 time stamp capture on transmit and receive Diagnostics Frame generator and checker Multiple loopback modes IEEE test mode support Port dedicated statistics counters Link and cable diagnostics 25 MHz crystal or external clock input Single or dual supply with 1.8 V or 3.3 V operation Integrated power supply monitoring and POR Small package: 48-lead, 7 mm × 7 mm LFCSP Temperature range Industrial: 40°C to +85°C Extended: 40°C to +105°C

Precision MEMS IMU Module Features: Triaxial, digital gyroscope  ±125°/sec, ±500°/sec, ±2000°/sec dynamic range models 2°/hr in-run bias stability (ADIS16465-1)  0.15°/√hr angular random walk (ADIS16465-1 and ADIS16465-2)  ±0.05° axis to axis misalignment error  Triaxial, digital accelerometer, ±8 g 3.6 μg in-run bias stability Triaxial, delta angle, and delta velocity outputs Factory calibrated sensitivity, bias, and axial alignment Calibration temperature range: −40°C to +85°C   SPI-compatible data communications Programmable operation and control  Automatic and manual bias correction controls Data ready indicator for synchronous data acquisition External sync modes: direct, pulse, scaled, and output On demand self test of inertial sensors On demand self test of flash memory Single-supply operation (VDD): 3.0 V to 3.6 V 2000 g mechanical shock survivability Operating temperature range: −40°C to +105°C

Precision, Miniature MEMS IMU Features: Triaxial, digital gyroscope ±125°/sec, ±500°/sec, ±2000°/sec dynamic range models 2.3°/hr in-run bias stability (ADIS16507-1) 0.13°/√hr angular random walk, x-axis and y-axis, 1 σ (ADIS16507-1) ±0.25° axis to axis misalignment error Triaxial, digital accelerometer, ±392 m/sec2 dynamic range 125 μm/sec2 in-run bias stability, x-axis and y-axis, 1 σ Triaxial, delta angle and delta velocity outputs Factory calibrated sensitivity, bias, and axial alignment Calibration temperature range: −40°C to +85°C SPI compatible data communications Programmable operation and control Automatic and manual bias correction controls Data ready indicator for synchronous data acquisition External sync modes: direct, scaled, and output On demand self-test of inertial sensors On demand self-test of flash memory Single-supply operation (VDD): 3.0 V to 3.6 V 19,600 m/sec2 mechanical shock survivability Operating temperature range: −40°C to +105°C

400 MHz TO 4000 MHz Low Noise Amplifier Features: Operation from 400 MHz to 4000 MHz Noise figure of 0.8 dB at 900 MHz Requires few external components Integrated active bias control circuit Integrated dc blocking capacitors Adjustable bias for low power applications Single-supply operation from 3 V to 5 V Gain of 20.8 dB at 900 MHz OIP3 of 37.0 dBm at 900 MHz P1dB of 21.8 dBm at 900 MHz Small footprint LFCSP Pin-compatible version with 21.5 dB gain available

5.7 kV RMS/1.5 kV RMS, Quad-Channel LVDS 2.5 Gigabit Isolator (0 Reverse Channels) Features: 5.7 kV rms and 1.5 kV rms LVDS isolators Complies with TIA/EIA-644-A LVDS signal levels Quad-channel configuration Any data rate up to 2.5 Gbps switching with low jitter 10 Gbps total bandwidth across four channels 2.15 ns typical propagation delay Typical jitter: 0.82 ps rms random, 40 ps total peak Lower power 1.8 V supplies ±8 kV IEC 61000-4-2 ESD protection across isolation barrier High common-mode transient immunity: 100 kV/μs typical Safety and regulatory approvals (28-lead SOIC_W_FP package) UL (pending): 5700 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A (pending) VDE certificate of conformity (pending) DIN V VDE V 0884-11 (VDE V 0884-11):2017-01 VIORM = 849 VPEAK (working voltage) Enable or disable refresh (low speed output correctness check) Operating temperature range: −40°C to +125°C 28-lead, wide-body, finer pitch SOIC_W_FP package with 8.3 mm creepage and clearance or 6 mm × 6 mm LFCSP package with 1.27 mm creepage and clearance

Three-Channel, Isolated Micropower Management Unit with Seven Digital Isolators Features: Wide input supply voltage range: 4.5 V to 60 V Integrated flyback power switch Generates isolated, independent bipolar outputs and factory programmable buck output VOUT1: 21 V, 24 V or 6 V to 28 V VOUT2: 5.15 V, 5.0 V, or 3.3 V VOUT3: −24 V to −5 V Uses a 1:1 ratio transformer for simplified transformer design Peak current limiting and OVP for flyback, buck, and inverting regulators Precision enable input and power-good output Adjustable switching frequency via SYNC input Internal compensation and soft start control per regulator High speed, low propagation delay, SPI signal isolation channels Three, 100 kbps general-purpose isolated data channels 9 mm × 7 mm LFCSP form factor enables small overall solution size −40°C to +125°C operating junction temperature range Conforms to CISPR11 Class B radiated emission limits Safety and regulatory approvals (pending) UL recognition: 2500 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A 300 V rms basic insulation between slave, master, and field power domains (IEC 61010-1, pending) VDE certificate of conformity DIN V VDE 0884-10 (VDE 0884-10):2006-12 VIORM = 565 VPEAK

Two-Channel, Isolated Micropower Management Unit with Seven Digital Isolators Features: Wide input supply voltage range: 4.5 V to 60 V Integrated flyback power switch Generates two isolated, well regulated independent outputs VOUT1: 24 V or 6 V to 28 V VOUT2: 3.3 V, 5.0 V, or 5.15 V Uses a 1:1 ratio transformer for simplified transformer design Peak current limiting and OVP for flyback and buck regulators Precision enable input and power-good output Adjustable switching frequency via SYNC input Internal compensation and soft start control per regulator High speed, low propagation delay, SPI signal isolation channels Three 100 kbps general-purpose isolated data channels 41-lead, 9 mm × 7 mm LFCSP form factor enables small overall solution size −40°C to +125°C operating junction temperature range Safety and regulatory approvals (pending) CISPR11 Class B radiated emission UL recognition: 2500 V rms for 1 minute duration per UL 1577 CSA Component Acceptance Notice 5A 300 V rms basic insulation between slave, master, and field power domains (IEC 61010-1, pending) VDE certificate of conformity DIN V VDE 0884-10 (VDE 0884-10):2006-12 VIORM = 565 VPEAK

Digital Controller for Power Supply Applications with PMBus Interface Features: −40°C to +125°C operation with EEPROM data retention of 15 years at 125°C PMBus Revision 1.2 compliant 32-bit password protection with command masking 64 address selections (16 base addresses, expandable to 64) 6 PWM control signals, 625 ps resolution Duty cycle double update rate Digital control loop (PID + additional pole or zero configurability) Programmable loop filters (CCM, DCM, low/normal temperature) Frequency synchronization Soft start and soft stop functionality Average and peak constant current mode External PN junction temperature sensing 4 GPIOs (2 GPIOs configurable as active clamp snubber PWMs) Fast line voltage feedforward Adaptive dead time compensation for improved efficiency Extended black box data recorder for fault recording See datasheet for additional features

Isolated Synchronous Flyback Controller with Integrated iCoupler Features: Current mode controller for flyback topology ADP1071-1: programmable LLM or CCM for high VIN applications ADP1071-2: forced CCM operation Programmable slope compensation Integrated 5 kV isolation (wide body SOIC package) or 3.0 kV (LGA package) rated dielectric isolation voltage with Analog Devices, Inc., patented iCoupler technology Wide voltage supply range Primary VDD: up to 60 V (ADP1071-2 only) Secondary VDD2: up to 36 V Integrated 1 A primary side MOSFET driver Integrated 1 A secondary side MOSFET drivers for synchronous rectification Integrated error amplifier and <1% accurate reference voltage Programmable frequency range: 50 kHz to 600 kHz Duty cycle clamp limit 85% Programmable soft start and soft start from precharged load Protection features such as short circuit, output overvoltage, and overtemperature protection Power saving LLM using MODE pin (ADP1071-1only) Cycle by cycle input overcurrent protection Precision enable UVLO with hysteresis Frequency synchronization Safety and regulatory approvals (pending) UL recognition 5000 V rms for 1 minute per UL 1577 (for wide body SOIC package) 3000 V rms for 1 minute per UL 1577 (for LGA package) CSA Component Acceptance Notice 5A VDE certificate of conformity DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 VIORM = 849 V peak (for wide body SOIC package) VIORM = 565 V peak (for LGA package) CQC certification per GB4943.1-2011 Available in 16-lead SOIC_W package and 24 terminal LGA package

Ultralow Noise, 150 mA CMOS Linear Regulator Features: Chinese data sheet available Ultralow noise: 9 μV rms, independent of VOUT No additional noise bypass capacitor required Stable with 1 μF ceramic input and output capacitors Maximum output current: 150 mA Input voltage range: 2.2 V to 5.5 V Low quiescent current IGND = 10 μA with zero load Low shutdown current: <1 μA Low dropout voltage: 105 mV at 150 mA load Initial output voltage accuracy: ±1% Up to 14 fixed output voltage options: 1.8 V to 3.3 V PSRR performance of 70 dB at 10 kHz Current limit and thermal overload protection Logic-controlled enable 5-lead TSOT package 4-ball, 0.8 mm × 0.8 mm, 0.4 mm pitch WLCSP AEC-Q100 qualified for automotive applications